ISC DW200 User manual
1
DW200.2: Issue A - Aug 2017
Deadweight
A-Frame Anchor
2
Deadweight
DW200.2: Issue A - Aug 2017
+2
1
Deadweight Anchors
DW200 A Frame
A
1X = ≤ 5°
XX
General Limitations
This DW200.2 A Frame is primarily designed and tested to be used as a portable anchor device for
Rope Access (work positioning) systems/activities.
The DW200.2 A Frame has been tested in accordance with EN795: 2012 Type E by SATRA in the
UK and CE marked accordingly.
The unit has been further tested and found to meet the requirements of PD CEN/TS 16415: 2013 ‘an-
chor devices for two person rescue’ and also the IRATA and SPRAT ICoP requirement that anchors
for rope access must meet a 15kN static test.
For rope access standards requirements please refer to ISO 22846-1:2003, BS7985: 2002, BS
EN12841: 2006, BS7883 or equivalent international standards and Codes of Practice.
Installation Considerations
• Roof surface is appropriate, i.e. Surface material, ballast, water, foreign matter, angle. All of these
factors could affect the frictional resistance of the device and create a hazard
• All loose surface material should be removed before assembly and installation of the device
Users of this equipment shall be able to demonstrate either in-house expertise or hold suitable train-
ing certicates in Working at Height / industrial rope access
Rescue – The device has a Maximum Rated Load of 200kg (440lbs) and can be used for a 2 person
load in a rescue situation in accordance with PD CEN/TS 16415: 2013
There must be sufcient free space beneath the user at the work area before each occasion of use,
so that in the case of a dynamic event there will be no collision with the ground or other obstacles
in the fall path
3
DW200.2: Issue A - Aug 2017
Deadweight
2
??KG ??KG
3
4
Deadweight
DW200.2: Issue A - Aug 2017
4
5
5
DW200.2: Issue A - Aug 2017
Deadweight
[A] General Limitations
1. The Deadweight should not be used on a surface that slopes more than 5o.
2. The Deadweight must be used so that the operator is in line with the equipment’s direction to
prevent the possibility of a pendulum occuring in the event of a fall
3. Ensure that the strength of the structure is adequate
4. The Deadweights should not be used on frozen surfaces. The presence of ice may cause the
unit to slip
5. The Deadweight is for use by a single person. In the event of a rescue being required, the Dead-
weight can be used with a 2 person load in accordance with PD CEN/TS 16415: 2013
6. Do not use Deadweight anchors outside of their limitations as outlined in this manual
7. The user shall be equiped with means of limiting the maximum dynamic forces exerted on the user
during a dynamic event to less than 6kN
8. If the intention is to combine PFPE for Fall Arrest with Deadweight Anchors the user should seek
guidance from the manufacturer as to its suitability. Always ensure that all components within a
safety system are compatible and allow the system to function safely
1
B Use
6
Deadweight
DW200.2: Issue A - Aug 2017
2
1500mm (59”) Max.
3
300mm (12”) Min
7
DW200.2: Issue A - Aug 2017
Deadweight
5
4
Brake Off Brake On
8
Deadweight
DW200.2: Issue A - Aug 2017
KG
1
CGeneral Misuse
6
[B] Use
1. The DW200 is designed to be used as part of a roped access system with twin ropes, work posi-
tioning harness and associated equipment
2. The DW200 should be used with a parapet wall with a minimum height of 300mm (12”)
3. The DW200 should be used with a parapet wall with a maximum height of 1800mm (59”)
4. Wheel brake operation. To unlock the wheel, push down the braking lever on the side marked OFF
The wheel will now rotate. To lock the wheel, push down the braking lever on the side marked ON.
Wheel brake operation. To unlock the wheel, pull the red locking bolt out and rotate 180ocounter
clockwise. The wheel will now rotate. To lock the wheel, reverse this process.
5. Care should be taken when repositioning the DW200 whilst a person is suspended. This option
should be thoroghly risk assessed by a competent person
6 If no parapet wall is available, then the DW200 may be tied back to a suitable anchor to prevent
unintentional movement. Soft slings should be used around the rear wheel support assembly [11]
This option should be thoroghly risk assessed by a competent person
9
DW200.2: Issue A - Aug 2017
Deadweight
2
3
10
Deadweight
DW200.2: Issue A - Aug 2017
2
1
3
4
5
6
7
8
9
10
1112
13
DNomenclature
[C] Misuse
1. The Deadweight should only be used for people. It should not be used for suspending loads
2. All weights must be used at all times. Weights may need to be secured to the frame by passing a
chain through the handles and the frame to prevent tampering during use
3. Do not use the Deadweight as an anchor for Self Retracing Lanyards
Other ISC Safety Equipment manuals
ISC
ISC RP248 Instruction manual
ISC
ISC RP048 Instruction manual
ISC
ISC CRESTO RP034A User manual
ISC
ISC RP815 Instruction manual
ISC
ISC Zip Trolley Series Instruction manual
ISC
ISC RP500 Instruction manual
ISC
ISC RP248 Instruction manual
ISC
ISC Keeloc SmartSnap RP420 Instruction manual
ISC
ISC D2 Instruction manual
ISC
ISC RP229 Operator's manual
Popular Safety Equipment manuals by other brands
Innova
Innova Xtirpa Instruction and safety manual
bolle SAFETY
bolle SAFETY B810 quick start guide
SHENZHEN FANHAI SANJIANG ELECTRONICS
SHENZHEN FANHAI SANJIANG ELECTRONICS A9060T instruction manual
Hiltron security
Hiltron security POWER8E Installation and use manual
Hatco
Hatco B-950P installation guide
Sitec
Sitec TX MATIC operating manual
