iplex DVRMOB1 Installation instructions
DVRMOB1
I Channel DVR for SD Interface
2
1CH Mini DVR Full Manual V.1.0
GENERAL SAFETY AND PRECAUTIONS
This Mini DVR is manufactured to meet international safety standards. Review the following safety
precautions to avoid injury and prevent damage to the DVR or any products connected to it.
1. Use a correct power source. Do not connect this product to a power source that supplies more than
the specified voltage (DC12V), as this will cause damage to the unit.
2. Never insert anything metallic into the DVR as this can cause electric shock.
3. Do not operate in wet & dusty conditions. Keep product surfaces clean and dry. Avoid placing the
DVR in areas like a damp basement or a dusty hallway.
4. Do not expose this product to rain or use near water. If the product gets wet, unplug it and contact an
authorized dealer immediately.
5. To clean the outside case of the DVR, use a lightly dampened cloth (no solvents).
6. Do not operate if you suspected to unit is faulty. If there are any unusual sounds or smells coming
from the DVR, immediately unplug it and contact an authorized dealer or service centre.
7. Do not attempt to remove the top cover.
Warning: Removing the DVR’s cover can cause an electrical shock.
8. Handle DVR carefully to avoid damaging the product. Dropping your DVR on any hard surface may
cause the unit to malfunction. If the DVR doesn’t work properly due to physical damage, contact an
authorized dealer for repair or exchange.
9. The unit has a lithium battery preinstalled.
10. The standard lithium cell 3V battery located on the motherboard should be replaced if the time clock
does not hold its time after the power is turned off.
3
1CH Mini DVR Full Manual V.1.0
TABLE OF CONTENTS
Chapter 1: Packing Contents
CONTENTS IN THE PACKAGE 05
Chapter 2: Getting To Know Your DVR
1CH Mini DVR 06
Chapter 3: Remote control
REMOTE CONTROL PANEL 08
Chapter 4: Getting Started
OVERVIEW OF SET UP PROCEDURES 09
Chapter 5: Hardware Installation
SD MEMORY INSTALLATION 10
CONNECTING MINI DVR TO YOUR MONITOR OR TELEVISION 10
ALARM INSTALLATION 12
Chapter 6: DVR Menu
1. ACCESS TO OSD MENU 13
2. MAIN MENU 13
3. RECORD MODE 14
4. VIDEO QUALITY 14
5. EVENT MODE 15
6. SEARCH 17
7. SUB MENU 18
4
1CH Mini DVR Full Manual V.1.0
7.1 PASSWORD CHANGE
7.2 TIME SET
7.3 BRIGHTNESS
7.4 AUDIO
7.5 VIDEO
7.6 MEMORY SYNC
19
19
20
20
21
21
8. DEFAULT 22
Appendix:
TECHNICAL SPECIFICATIONS 23
RECORDING TIME TABLE RECORDING 24
5
1CH Mini DVR Full Manual V.1.0
Chapter 1: Packing Contents
▶Contents in the package
DVR Main Unit Remote Control AV-IN / AV-OUT Cable
Terminal Block 12V Power Supply Installation CD
Quick Guide SD Card (Option) USB SD Reader (Option)
6
1CH Mini DVR Full Manual V.1.0
Chapter 2: Getting To Know Your DVR
▶DVR
This chapter briefly describes the functions of each connection and LED on DVR. For more details on the
set-up and operation of , refer to Chapter 6, DVR MENU.
1Sensor-in / Alarm-out
Use the supplied terminal block to connect PIR type sensor to the DVR. By adding motion sensor
devices to your DVR, the video recording can be triggered by events.
The alarm output terminal will trigger a single external device.
2SD Memory Slot
①
②
③⑤
⑥
⑦
⑧⑨ ⑩
④
7
1CH Mini DVR Full Manual V.1.0
Insert SD Card into the data storage slot.
3Recording LED
This light indicates while DVR is recording.
4Status LED
This light flashes when an event or any error has occurred.
5Power LED
This light indicates when the DVR is powered up.
6Remote Control Receiver
The remote control must be pointing at the DVR and be in line of sight to work.
7Reset
Pressing the reset button will return the DVR setting to factory default.
8AV-IN
Connect AV-IN video / camera cable.
9 AV-OUT
Connect AV-OUT monitor cable.
10 Power
Connect 12V power supply.
8
1CH Mini DVR Full Manual V.1.0
Chapter 3: Remote control
1 REC: Starts DVR recording.
2
MENU: Enters the DVR ‘MENU’ mode.
3 UP/ DOWN buttons to chooses menu fields and changes values.
4 Plays recorded video forward. Plays recorded video backward.
5 REW: Fast Rewind button
6
FF: Fast forward button
7
PLAY: The button to start video playback.
8
STOP: The button to stop playback or recording.
9
PAUSE: The button to pause video playback.
10
MUTE: The button to pause audio.
11 ENT: The button to choose or change a menu option or values in a menu field.
12
SEARCH: The button to find recorded files in SD Memory.
13
MODE: The button to switch between playback and recording mode.
9
1CH Mini DVR Full Manual V.1.0
Chapter 4: Getting Started
OVERVIEW ON SET-UP PROCEDURES
Below is an overview of the MINI DVR installation procedures, (A detailed explanation is found in
Chapter 5 – Hardware Installation.)
(1) Insert a SD MEMORY.
(2) Connect the DVR to a monitor of television.
(3) Connect a camera to the DVR
(4) Connect optional accessories (sensors or alarm).
(6) Connect the power.
(7) Turn the power on.
(8) Start TV Monitoring and recording.
GeneralOperatingAdvice:
●Make sure that a SD Memory card is inserted and the camera is properly connected.
(See Chapter 5 -Hardware Installation)
●The firmware used in DVR is compatible with your computer’s operating system (i.e. Windows). Therefore,
you can take the SD memory card from this DVR and install it in your computer to view recorded video. (Refer
to the DVR Player manual.)
●DVR offers you the flexibility to choose a recording frame rate (maximum rate: 30 frames per second). The
faster frame rate the greater the SD Memory storage capacity required. Reducing the frame rate (minimum
rate: 1 frame per 10 seconds) will allow a greater recording duration.
●When connecting a camera is to DVR, the unit enters the default operational state: “VIEW mode”.
In this mode, DVR does not record nor play the recorded stream, but only shows the current images from the
camera.
●The default recording values for the DVR are 30 frames per second (25frames in PAL) with normal video
quality. If you use 1GB SD Memory, DVR can record for approximately 2 hours.
●If the power is inappropriately turned off while DVR is in the record mode (i.e. power failure), it will re-enter
the record mode automatically when power is re-established.
Refer to Chapter 5 - Hardware Installation for more information on installation procedures.
10
1CH Mini DVR Full Manual V.1.0
Chapter 5: Hardware Installation
SD MEMORY INSTALLATION
①Format SD Memory
Most SD cards are pre-formatted to FAT32. If not, insert the
card into the SD card slot on your PC and format it there.
※In case there is no card slot on your PC, use and external
card reading device.
②Insert SD Memory into SD slot
on DVR
After formatting, take the SD Memory card from your PC and
insert it into SD slot on DVR.
③Backup recorded files in SD Memory
When SD Memory storage is full, the recorded files can be
backed up in your PC. Insert SD card in your PC and move
the files of SD card into the HDD of our PC. You can also
check each recorded file through DVR Player.
※It is recommended that only SanDisk or Transcend SD cards are used, these are compatible with DVR.
※Be sure to turn off DVR first when you take out SD card from the slot.
CONNECTING DVR TO YOUR MONITOR OR TELEVISION
①Video Input/Output Connection (For monitor / TV screen display)
Table of contents
