Invacare 9153644014 Assembly instructions

Part No 1130250 1Installing Front Riggings on the At’m

For more information regarding Invacare products, parts, and services,

please visit www.invacare.com

Installing Front Riggings on the At’m

Kit Numbers: 9153644014, 9153644018

NOTE: Check all parts for shipping damage. In case of damage, DO NOT use. Contact

Carrier/Invacare for further instructions.

Safety Summary

To ensure the safe and proper installation and use of the front riggings on the At’m, these

instructions MUST be followed:

 WARNING

After ANY adjustments, repair or service and BEFORE use, make sure that all

attaching hardware is tightened securely - otherwise injury or damage may result.

Invacare products are specifically designed and manufactured for use in conjunction

with Invacare accessories. Accessories designed by other manufacturers have not

been tested by Invacare and are not recommended for use with Invacare products.

Description of the Kit

Kit Numbers 9153644014 and 9153644018 for Red or Blue At’m Front Riggings contain:

Installing Front Rigging Support Brackets

NOTE: For this procedure, refer to FIGURE 1.

NOTE: Perform the following steps one (1) side at a time.

1. Remove the plug button from the seat frame tube.

2. Note the orientation of the hardware that connects front seat support tube to the seat

frame tube.

3. Remove the mounting screw, coved washers, spacers, washers and locknut securing

front seat support tube to the seat frame tube. DO NOT discard.

Assembly, Installation and Operating Instructions

SAVE THESE INSTRUCTIONS

PART NUMBER DESCRIPTION QUANTITY

1132651 Right Legrest Support Assembly 1

1132652 Left Legrest Support Assembly 1

1133151 Mounting Hardware Assembly 1

1134702 70° Complete Right Footrest Assembly 1

1134703 70° Complete Left Footrest Assembly 1

Installing Front Riggings on the At’m 2Part No 1130250

4. Insert the proper (right or left) front rigging support bracket into the seat frame

tube until two (2) of the four (4) mounting holes on the front rigging support

bracket are aligned with the two (2) mounting holes in the seat frame tube.

CAUTION

Two (2) mounting screws are used to secure the front rigging support

bracket to the seat frame tube for any mounting position used.

5. Install the existing mounting screw, coved washers, spacers, washers and

locknut that secure front seat support tube to the seat frame tube in the

orientation noted in STEP 2. DO NOT tighten locknut at this time.

6. Install the new mounting screw, spacer and locknut (hardware supplied)

through the large mounting hole on the seat frame tube. Securely tighten.

NOTE: Make sure that the spacer is aligned with the large mounting hole in the seat frame

tube and is properly seated against the front rigging support bracket during and after

tightening. Refer to Detail “A” of FIGURE 1.

7. Tighten the locknut securing the front seat tube to the seat frame until it is snug

and then turn an extra 1/8-turn. DO NOT over-tighten as this is a pivot joint

when folding the seat.

8. Repeat STEPS 1-7 to install the front rigging support bracket on the other side.

FIGURE 1 Installing Front Rigging Support Brackets

Coved Washers

Spacer

Spacer Locknut

Locknut

Existing Mounting

Screw

New Mounting

Screw

Spacer

Front Rigging

Support

Bracket

Front Seat

Support

Tube

Seat Frame Tube

Front Rigging

Support

Bracket

Spacer

Front Seat

Support Tube

Seat Frame Tube

*Large

Mounting Hole

*Small

Mounting Hole

Mounting Holes

on Front Riggings

Support Bracket

DETAIL “A”

*NOTE: Mounting hole

arrangement on 16-inch wide

seat shown. On the 18-inch

wide seat, the mounting hole

positions are reversed.

Part No 1130250 3Installing Front Riggings on the At’m

Installing/Removing the Front Rigging Assembly

NOTE: For this procedure, refer to FIGURE 2.

Installing

1. Turn the front rigging assembly to the side (open footrest is perpendicular to

the wheelchair).

2. Insert the mounting pin on the front rigging assembly into the front rigging

support bracket.

3. Rotate the front rigging assembly towards the inside of the wheelchair until it

locks into place.

NOTE: The footplate will be facing the inside of the wheelchair when locked in place.

4. Repeat STEPS 1-3 for the other front rigging assembly.

5. If necessary, adjust the footrest height. Refer to Adjusting Footrest Height on

page 4.

Removing

1. Push the front rigging release lever inward while rotating the front rigging

assembly outward.

2. Lift the front rigging assembly out of the front rigging support bracket.

3. Repeat STEPS 1-2 for the other front rigging assembly, if necessary.

FIGURE 2 Installing/Removing the Front Rigging Assembly

Seat Frame Tube

Footrest

Mounting Pin

Front Rigging

Assembly

Front Rigging

Support Bracket

Front Rigging

Release Lever

Outside of

Wheelchair

Inside of

Wheelchair

Adjusting Footrest Height

NOTE: For this procedure, refer to FIGURE 3.

1. Remove the front rigging assembly. Refer to Installing/Removing the Front Rigging

Assembly on page 3.

2. Remove the hex screw and coved spacer.

3. Move the footrest with slide tube up or down on its mounting tube until the desired

footrest height is achieved.

4. Install the hex screw and coved spacer through the front rigging upper support and

the slide tube. Securely tighten.

5. Install the front rigging assembly. Refer to Installing/Removing the Front Rigging

Assembly on page 3.

6. Repeat STEPS 1-5 for the other side, if necessary.

FIGURE 3 Adjusting Footrest Height

Footrest

Slide Tube

Coved Spacer

Hex Screw

Front Rigging

Upper Support

Invacare Corporation www.invacare.com

USA

One Invacare Way

Elyria, Ohio USA

44036-2125

800-333-6900

Canada

570 Matheson Blvd E Unit 8

Mississauga Ontario

L4Z 4G4 Canada

800-668-5324

Invacare is a registered trademark of

Invacare Corporation.

Yes, you can. is a trademark of Invacare

Corporation

Part No 1130250

Rev A - 06/05

This manual suits for next models

Table of contents

Other Invacare Mobility Aid manuals

Invacare

Invacare Aquatec 90000 User manual

Invacare

Invacare ESS-PTO Instruction Manual

Invacare

Invacare RPS350-2 Manual

Invacare

Invacare Infinity Back Support Manual

Invacare

Invacare Izzo User manual

Invacare

Invacare 6252 Assembly instructions

Invacare

Invacare Aquatec Marine User manual

Invacare

Invacare Action 2000 User manual

Invacare

Invacare Lima H263 User manual

Invacare

Invacare Balnea User manual

Invacare

Invacare TRHD22HR User manual

Invacare

Invacare 1305L Assembly instructions

Invacare

Invacare Spartan 65420 User manual

Invacare

Invacare KSS User manual

Invacare

Invacare InTouch 1143199 Operation manual

Invacare

Invacare Dolomite Jazz 510 User manual

Invacare

Invacare 65510 Assembly instructions

Invacare

Invacare 1514 User manual

Invacare

Invacare P402 Aventia User manual

Invacare

Invacare Dolomite Gloss User manual

Invacare

Invacare DOLOMITE Futura User manual

Invacare

Invacare Camlock Upgrade Kit 1052250 User manual

Invacare

Invacare Dolomite Maxi+ User manual

Invacare

Invacare 6264P Assembly instructions

Popular Mobility Aid manuals by other brands

Alber

Alber Scalamobil iQ operating instructions

Ferno

Ferno CCT-PX user manual

HEPRO

HEPRO Gripo user manual

Otto Bock

Otto Bock Pheon 3R62 Instructions for use

NRS Healthcare

NRS Healthcare M11090 User instructions

Medline

Medline MDS86835DSHEC User Instructions & Warranty

Guldmann

Guldmann Twin Turner II user manual

Drive

Drive ROOMBA Operation manual

Gate

Gate Balder operating instructions

Decon wheel

Decon wheel TNS Notos Assembly instructions

ExoAtlet

ExoAtlet ExoAtlet-II user manual

Rhythm Healthcare

Rhythm Healthcare B3800F manual

AMF-BRUNS

AMF-BRUNS PROTEKTOR installation manual

Drive DeVilbiss Healthcare

Drive DeVilbiss Healthcare OTTER Instructions for use

Rhythm Healthcare

Rhythm Healthcare C500U Assembly and Fitting Instructions

Lumex

Lumex RJ4200A manual

Rebotec

Rebotec Jumbo user manual

Rehaforum MEDICAL

Rehaforum MEDICAL PR50548 manual