Interlogix Sentrol DV1201A User manual

- 1 -

DV1201A & DV1221A

Seismic Detectors Installation Manual

Figure 2: Two ways to test the seismic detectors

1/2. 12 Vdc 7. Common (C)

3. LED indication 8/9. Tamper

4. Integrator level 10. Test control

5. Normaly Closed (NC) 11. Spare

6. Normaly Open (NO)

Test disabled (ex-factory setting)

Internal test of detector’s electronics =

Position jumper between 1 and 2 .

Function test of the detector and its physical contact

with the protected object = Position connector from

test transmitter DV1215A between 2 and 3.



Connecting terminal 10 to 0 V activates both tests.

1. Cover

2. Cover screw

3. Base plate

4. Mounting holes

5. Clamp

6. Area for mounting the

DV1215A test transmitter

7. Potentiometer for adjusting

the detector’s sensitivity

8. Connection block

9. Anti-tamper micro-switch

10. Mounting plate DV1202A

11. Fixing bolt

12. Expander bolt

13. Test transmitter DV1215A

Figure 3: General characteristics of the DV1201A / DV1221A

Using the mounting plate DV1202A as a template

A. Holes for DV1201A / DV1221A

B. Hole for expansion plug or recess mounting box

C. Template and mounting holes for test transmitter DV1215A

D. Holes for accessories.

Figure 4: Mounting the detector directly on a metal surface without using a mounting plate

Figure 1: Wiring diagram

Sentrol

24-04-'02

Manual DV1201A / DV1221A 14 999-

5620

Form: Letter (bookshape)

Formaat: Letter (boekvorm)

G. Manders

110-01

White paper: 70gr/m² progresso; overprint black. If P.O.D.: use 80gr/m².

Wit papier: 70gr/m² progresso; opdruk zwart. Wanneer P.O.D.: gebruik 80gr/m². 1 A 24-04-'02 10423-10424

- 1 -

DV1201A & DV1221A

Seismic Detectors Installation Manual

Figure 2: Two ways to test the seismic detectors

1/2. 12 VDC 7. Common (C)

3. LED indication 8/9. Tamper

4. Integrator level 10. Test control

5. Normaly Closed (NC) 11. Spare

6. Normaly Open (NO)

!Test disabled (ex-factory setting)

"Internal test of detector’s electronics =

Position jumper between 1 and 2 .

#Function test of the detector and its physical contact

with the protected object = Position connector from

test transmitter DV1215A between 2 and 3.

Connecting terminal 10 to 0 V activates both tests.

1. Cover

2. Cover screw

3. Base plate

4. Mounting holes

5. Clamp

6. Area for mounting the

DV1215A test transmitter

7. Potentiometer for adjusting

the detector’s sensitivity

8. Connection block

9. Anti-tamper micro-switch

10. Mounting plate DV1202A

11. Fixing bolt

12. Expander bolt

13. Test transmitter DV1215A

Figure 3: General characteristics of the DV1201A / DV1221A

Using the mounting plate DV1202A as a template

A. Holes for DV1201A / DV1221A

B. Hole for expansion plug or recess mounting box

C. Template and mounting holes for test transmitter DV1215A

D. Holes for accessories.

Figure 4: Mounting the detector directly on a metal surface without using a mounting plate

Figure 1: Wiring diagram

Sentrol

- 2 -

Figure 5: Mounting on concrete

Always use a DV1202A mounting plate. The expansion plug must

penetrate at least 50 mm into the concrete. Please follow the steps

shownin Figure 6 ifyouareinstallingthetest transmitter DV1215A.

For the equipment to conform to CEI standard 79-2, the

DV1215A test transmitter must be installed.

Figure 6: Control and function test

Usingavoltmeter,checkthe background signal levelinthedetector

to prevent nuisance alarms. Set the sensitivity to Gmax during the

test.

DV1201A DV1221A Measure

0.7 V 0 V None

1.4 V 2 V Reduce range/remove source

Try to remove the source of ambient noise instead of

reducing the range.

Functional testing with hand tester DV1230 !and mechanical

tool ":

DV1201A DV1221A

Alarm in 30 sec. Alarm in 45 sec.

Alarm after 5 blows NA

Detection range (in foot): Technical specifications:

Input power: 9-15 VDC

2 V max. ripple pp

Current consumption: Nom. 8.6 mA

Alarm output: Form C solid state relay, max. series

resistance 35 Ohm

Alarm indication: LED-ind. output 3

Sensitivity: 5 steps of 6 dB each

Range: See Table “Detection range”

Sabotage protection: Temp. 183.2 °F

drill shield,

opening/pry-off contact,

Low voltage alarm: 7.5 V

Temperature limits: -4 °F to + 131 °F

Dimensions: 3.93 x 3.15 x 1.30 inches

Colour: Grey, RAL 7035

Weight: 0.86 lb

Concrete 13.12 45.93 45.93

Steel 1/Gmax 26.25 45.93 45.93

Brick 9.84 26.25 26.25

Concrete 9.84 29.53 29.53

Steel 2/Gref 13.12 29.53 29.53

Brick 3.28 19.69 19.69

Concrete 6.56 19.69 19.69

Steel 3/Gmin 6.56 19.69 19.69

Brick - 13.12 13.12

Concrete 3.28 16.40 16.40

Steel 4 3.28 16.40 16.40

Brick - 9.84 9.84

Concrete - 13.12 13.12

Steel 5 - 13.12 13.12

Brick - 6.56 6.56

Sensitivity

setting

Material Thermal

lance Diamond

disk Drilling

- 3 -

Figure 7: Wiring the DV1201A/DV1221A into Most Security Systems

Figure 8: Connecting the DV1201A to a Four-wire Circuit

Type Control in an UL Complete Mercantile Safe System Figure 9: Connecting the DV1201A to a Two-wire Balanced

Loop Type Control in an UL Complete Mercantile Safe

System

Figure 10: Wire Diagram DV1208A

Figure 11

This manual suits for next models

Other Interlogix Security Sensor manuals

Interlogix

Interlogix TX-2511-03-1 Assembly instructions

Interlogix

Interlogix Firefighter SLX-AD-T3 Guide

Interlogix

Interlogix R5812NT User manual

Interlogix

Interlogix EV100 Assembly instructions

Interlogix

Interlogix AS520 Series User manual

Interlogix

Interlogix TVK-600 Instruction sheet

Interlogix

Interlogix RF-EV1012-K4 User manual

Interlogix

Interlogix ADC-IS-300-LP-BX User manual

Interlogix

Interlogix GS960AM User manual

Interlogix

Interlogix DD1012 Assembly instructions

Interlogix

Interlogix TX-2413-03-1 Assembly instructions

Interlogix

Interlogix AP633A User manual

Interlogix

Interlogix VE1016 Series Assembly instructions

Interlogix

Interlogix DD300-P Series Assembly instructions

Interlogix

Interlogix EV1012-D Series Assembly instructions

Interlogix

Interlogix VE1012 Series Assembly instructions

Interlogix

Interlogix RF711I4 Assembly instructions

Interlogix

Interlogix TX-4200-01-1 Assembly instructions

Interlogix

Interlogix VV600 Plus Assembly instructions

Interlogix

Interlogix TX-2344-03-1 User manual

Interlogix

Interlogix EV1116-D Series Assembly instructions

Interlogix

Interlogix GS903N Assembly instructions

Interlogix

Interlogix DC418 Specification sheet

Interlogix

Interlogix TX-2810-01-4 Assembly instructions

Popular Security Sensor manuals by other brands

THORLABS

THORLABS PDA10JT user guide

Waeco

Waeco UV-DETECT operating manual

Intermatic

Intermatic IOS-DSIMF manual

urmet domus

urmet domus 1083 manual

Siemens

Siemens AZL66 Series manual

BTI

BTI Profiline Multi Finder operating instructions

Challenger

Challenger SL01 instruction manual

DMP Electronics

DMP Electronics 1122INT installation guide

Rielta

Rielta Ladoga MK-RK installation guide

Mirion Technologies

Mirion Technologies ACCURAD PRD user manual

Bosch

Bosch DS835 installation instructions

DBI SALA

DBI SALA EZ Stop User instruction manual

Lamptime

Lamptime ST05C instructions

Ubiquiti

Ubiquiti MFI-MSC quick start guide

Subsite

Subsite 910R Support

Satel

Satel OPAL Pro manual

Aleph

Aleph XC-1XTEU manual

Pima

Pima LARIS QUAD installation instructions