Inter-m HDMS-0808 User manual
Operation Manual
Video Audio Matrix Switcher
HDMS-0808
* Rack mount pro ucts in the Western Hemisphere(North America, South America,
an the Caribbean) o not have han les installe ue to customer preference.
VIDEO AUDIO MATRIX SWITCHER
Welcome
Welcome
A personal welcome to you from the management and employees of Inter-M
All of the co-workers here at Inter-M are e icate to provi ing excellent pro ucts with inherently goo value,
an we are elighte you have purchase one of our pro ucts.
We sincerely trust this pro uct will provi e years of satisfactory service, but if anything is not to your complete
satisfaction, we will en eavor to make things right.
Welcome to Inter-M, an thank you for becoming part of our worl wi e exten e family!
RI K OF ELECTRIC HOCK
DO NOT OPEN
CAutION
CAUTION: TO REDUCE THE RI K OF ELECTRIC HOCK.
DO NOT REMOVE COVER (OR BACK).
NO U ER- ERVICEABLE PART IN IDE.
REFER ERVICING TO QUALIFIED ERVICE PER ONNEL.
WARNING
To prevent fire or shock hazard, do not
expose the unit to rain or moisture.
*WARNING FOR YOUR PROTECTION PLEA E READ THE FOLLOWING-WATER AND MOI TURE: Unit should not be used near water(e.g.
near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool, etc). Care should be taken so than objects do
not fall and liquids are not spilled into the enclosure through openings.
*Do not install this equipment in a confined space such as a book case or similar unit.
*This apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such vases, shall be placed on the apparatus.
*This apparatus shall be connected to a mains socket outlet with a protective earthing connection.
*
It has heed to be easy to disconnect the device. To disconnect the device from power, separate AC input cable from inlet or unplug the AC Cord.
CAutION
*These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock, do not perform any servicing
other than that contained in the operating instructions unless you are qualified to do so.
NOtE
*This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will
be required to correct the interference at his own expense.
This symbol is intended to alert the user to the
presence of uninsulated “dangerous voltage” within
the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to
persons.
This symbol is intended to alert the user to the
presence of important operation and maintenance
(servicing) instructions in the literature accompanying
the appliance.
Caution: To prevent electric shock do not use this (polarized) plug with
an extension cord, receptacle or other outlet unless the blades
can be fully inserted to prevent blade exposure.
Attentions: Pour prévenir les chocs électriques ne pas utiliser cette
fiche polarisée avec un prolongateur, une prise de courant
on une autre sortie de courant, sauf si les lames peuvent
étre insérées à fond sans en laisser aucune partie à
découvert.
VIDEO AUDIO MATRIX SWITCHER
1
HDMS-0808
Contents
Contents
Unpacking .......................................................................................................................................2
Installation
Environment....................................................................................................................................2
Important Safety Instructions.............................................................................................................2
Summary .........................................................................................................................................3
Features............................................................................................................................................3
Front Panel ......................................................................................................................................4
Rear Panel .......................................................................................................................................6
RS-232C Control.............................................................................................................................8
How to use ......................................................................................................................................8
How to connect...............................................................................................................................9
Applications ..................................................................................................................................12
Block Diagram ..............................................................................................................................13
Specifications ................................................................................................................................14
How to setup MASTER-SLAVE.....................................................................................................16
How to connect a DC adapter to the device............................................................................16
Service............................................................................................................................................19
Variations and Options ...............................................................................................................19
Warranty .......................................................................................................................................19
VIDEO AUDIO MATRIX SWITCHER
2HDMS-0808
Installation
Unpacking
Unpacking
Although your HDMS-0808 is neither complicate nor ifficult to operate, we recommen you take a few
minutes to rea this brief manual an familiarize yourself with the important information regar ing pro uct
features, setup an operation.
As with most electronic evices, we strongly recommen you to retain the original packaging. In the unlikely
event the pro uct must be returne for servicing, the original packaging (or reasonable equivalent) is require .
Installation
Environment
Never place this pro uct in an environment which coul alter its performance or re uce its service life. Such
environments usually inclu e high levels of heat, ust, moisture, an vibration.
IMPORTANT SAFETY INSTRUCTIONS
1. Rea these instructions.
2. Keep these instructions.
3. Hee all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with ry cloth.
7. Do not block any ventilation openings. Install in accor ance with the manufacturer’s instructions.
8. Do not install near any heat sources such as ra iators, heat registers, stoves, or other apparatus (inclu ing
amplifiers) that pro uce heat.
9. Do not efeat the safety purpose of the polarize or groun ing-type plug. A polarize plug has two bla es
with one wi er than the other. A groun ing type plug has two bla es an a thir groun ing prong. The wi e
bla e or the thir prong are provi e for your safety. If the provi e plug oes not fit into your outlet, consult
an electrician for replacement of the obsolete outlet.
10. Protect the power cor from being walke on or pinche particularly at plugs, convenience receptacles, an
the point where they exit from the apparatus.
11. Only use attachments/accessories specifie by the manufacturer.
12. Use only with the cart, stan , tripo , bracket, or table specifie by the manufacturer, or sol with the apparatus.
When a cart is use , use caution when moving the cart/apparatus combination to avoi injury from tip-over.
13. Unplug this apparatus uring lightning storms or when unuse for long perio s of time.
14. Refer all servicing to qualifie service personnel. Servicing is require when the apparatus has been
amage in any way, such as power-supply cor or plug is amage , liqui has
been spille or objects have fallen into the apparatus, the apparatus has been
expose to rain or moisture, oes not operate normally, or has been roppe .
S3125A
3125A
VIDEO AUDIO MATRIX SWITCHER
3
HDMS-0808
Summary
Summary
HDMS-0808 is FULL HD VIDEO an STEREO AUDIO MATRIX SWITCHER which can isplay 8 A/V inputs to 8
ran om outputs without eteriorations of picture an soun qualities.
It uses the irect switch controlling metho for easy controls, an it is esigne that controlle content is
isplaye on the front isplay, so you can see it without any ifficulty.
Because it has the RS-232C function, it can be controlle in PC, etc., an it can control two of these evices
connecte in parallel in a same time.
Features
Features
Features
- 8x8 A/V Matrix Switcher.
- Simple real-time output and DISCONNECTION function.
- Individual or real time control function for audio, video.
- Very low crosstalk and broad frequency response.
- Parallel connection.
- RS-232 function.
- Blackout compensation function which returns to right-before black out status.
- Vertical interval switching between GENLOCKed sources.
- LOCK function to prevent human error.
- Supporting resolution
SD class: 480i, 480p
HD class: 720i, 720p
Full HD class: 1080i
VIDEO AUDIO MATRIX SWITCHER
4HDMS-0808
Front Panel
Front Panel
1. DISPLAY WINDOW
Displays the vi eo input channel status which is output to each vi eo/au io output terminal.
“1”~”8” shows each channel, an if “0” is isplaye , nothing will be output.
2. INPUT/OUTPUT SELECT BUTTON
- Output : select the channel you want to output. Push this button, an then isplay win ow of correspon ing
channel will blink. If the input channel to be output is selecte while blinking, isplay win ow will
change to the correspon ing input channel an blinking will stop.
After start blinking, selection will be cancelle if there is no input for about 10 secon s.
- Input : select the input channel to be output to each output terminal.
3. ALL/OFF BUTTON
- ALL : select all output channels. If push this button, isplay win ows of all channels will blink. After start
blinking, selection will be cancelle if there is no input for about 10 secon s. ALL buttons are use
when you want to output one channel in all outputs or isconnect all outputs.
- OFF : it is use when isconnect the output channel. After selecting the OUTPUT SELECT button, push OFF
button, an then isplay win ow shows “0” an nothing will be output.
4. MODE SELECT BUTTON
Sets up the mo e status of No. 2 an 3 SELECT SWITCH.
- A/V : it sets up No. 2 an 3 SELECT button mo e status to simultaneous control mo e of Vi eo an Au io.
- Vi eo : it sets up No. 2 an 3 SELECT button mo e status to Vi eo Control Mo e.
- Au io : it sets up No. 2 an 3 SELECT button mo e status to Au io Control Mo e.
. LOCK BUTTON
It is the button to prevent the human error. After all channel settings are complete , click this button for 5
times, an then all buttons on the front will not work while LED of buttons will be isplaye .
To unlock, push it for 5 times again, an then LED will be OFF. Lock function will not be cleare even after
turning off the power an turning it on again.
1
6
245
3
VIDEO AUDIO MATRIX SWITCHER
HDMS-0808
6. POWER SWITCH
It is the switch for power ON/OFF.
VIDEO AUDIO MATRIX SWITCHER
6HDMS-0808
Rear Panel
Rear Panel
1. AC INPUT
It is AC co e input terminal use if user installs the DC a apter in the evice.
2. DC INPUT
It is DC 12V/ 3A power input terminal.
3. SELECT IN/OUT JACK
It is use when user wants to implement the parallel motion or remote motion by connecting up to 2 evices.
PIN NO. Signal Name Function
1 CONTROL IN/OUT 1
2 CONTROL IN/OUT 2
3 CONTROL IN/OUT 3
4 CONTROL IN/OUT 4
5 CONTROL IN/OUT 5 Control signal line
6 CONTROL IN/OUT 6
7 CONTROL IN/OUT 7
8 CONTROL IN/OUT 8
9 NC
10 UART1 TX
11 UART1 RX Serial communication
12 GND
13 GND
14 GND GND
15 GND
VIDEO AUDIO MATRIX SWITCHER
7
HDMS-0808
4. RS-232C JACK
It is use when you want to o same functions as button is pushe from the front by connecting this evice
to PC.
. VIDEO/AUDIO OUTPUT
Vi eo : isplay the input vi eo signal to ran om output terminal selecte from the front.
Au io : isplay the input au io signal to ran om output terminal selecte from the front.
6. VIDEO/AUDIO INPUT
Vi eo: input up to 1~8, maximum 8 channels of FULL HD vi eo signal.
Au io: input up to 1~8, maximum 8 channels of STEREO au io signal.
PIN NO. Signal Name Function
1 NC
2 TX Serial communication
3 RX Serial communication
4 NC
5 GND GND
6 NC
7 NC
8 NC
VIDEO AUDIO MATRIX SWITCHER
8HDMS-0808
RS-232C Control
RS-232C Control
- PROTOCOL
* RS-232C stan ar
* START Bit 1
* STOP Bit 1
* DATA Bit 8
* PARITY None
* DATA RATE 9600bps
* CODE ASC II
* TERMINATE
How to use
How to use
1. Connect video device
Vi eo input an output to be connecte to this evice shoul be connecte to RCA JACK locate at the
rear si e of matrix switch by using component cable.
※ CAUTION : when connecting to other input/output evice with component cable, component stan ar
or er (Y, Pb, Pr) shoul be matche .
2. Connect audio device
Au io input an output to be connecte to this evice shoul be connecte to RCA JACK locate at the
rear si e of matrix switch by using RCA TYPE CABLE.
At this time, L an R of RCA JACK locate at the rear si e of matrix switch shoul be matche .
Table of contents
Other Inter-m Matrix Switcher manuals
