Intel 5000 Series User manual
Intel®5000 Sequence Processor
Integration
Warning, Important Safety Instructions
System power on/off: The power button DOES NOT turn off the system AC power. To remove power
from system, you must unplug the AC power cord from the wall outlet. Make sure the AC power cord is
unplugged before you open the chassis, add, or remove any components.
Hazardous conditions, devices and cables: Hazardous electrical conditions may be present on power,
telephone, and communication cables. Turn off the server workstation and disconnect the power cord,
telecommunications systems, networks, and modems attached to the server workstation before opening
it. Otherwise, personal injury or equipment damage can result.
Electrostatic discharge (ESD) and ESD protection: ESD can damage disk drives, boards, and other
parts. We recommend that you perform all procedures in this chapter only at an ESD workstation. If one
is not available, provide some ESD protection by wearing an antistatic wrist strap attached to chassis
ground any unpainted metal surface on your server workstation when handling parts.
ESD and handling boards: Always handle boards carefully. They can be extremely sensitive to ESD.
Hold boards only by their edges. After removing a board from its protective wrapper or from the server
workstation , place the board component side up on a grounded, static free surface. Use a conductive
foam pad if available but not the board wrapper. Do not slide board over any surface.
Installing the Processor
Note:
• Do not touch the contacts on either the processor or the processor socket.
• Do not force the processor socket into place. When correctly aligned, the socket will easily drop
into place.
To install a processor, follow these instructions:
1. Observe safety and ESD precautions.
2. Turn off all peripheral devices connected to the server. Turn off the server.
3. Disconnect the AC power cord from the server.
4. Remove the chassis cover. See the documentation that came with your chassis for instructions
on removing the cover.
5. Locate the processor sockets (see Figure 1).
Figure 1. Example: Locating Processor Sockets.
Note: Consult Your Board Documentation for Proper Socket Location
6. Disconnect and remove any components necessary to access the processor sockets. See the
documentation that came with your chassis for instructions on removing chassis components.
7. Push down on the lever attached to the processor socket. While holding the lever down, pull it
towards the center of the board to disengage the lever from the hook. Fully open the lever. See
Figure 2.
Figure 2. Opening Processor Socket Lever
8. Push down on the rear tab of the load plate to swing the front of the load plate up slightly. Fully
open the load plate. See Figure 3.
Figure 3. Opening Load Plate
9. If the protective cover is attached from the load plate, remove it and store it for future use. See
Figure 4.
Figure 4. Removing Protective Cover from Load Plate
10. Remove the processor from the box and remove the protective shipping cover.
11. Set the processor in the socket with the processor cutouts matching the processor socket
notches. See Figure 5.
Figure 5. Setting Processor in Place
12. Close the load plate.
13. Close the socket lever. Push downward on the socket lever while pushing it toward the center of
the processor socket to engage it under the hook on the processor socket.
Installing the Heat Sink(s)
Note: The heat sink has thermal interface material (TIM) located on the bottom of it. Use
caution when handling the heat sink so you do not damage the TIM.
Each processor requires a heat sink. Depending on your chassis, you may need to use
either a active (Figure 6) or an passive heat sink (Figure 7). An active heat sink has a fan
attached to the top of it and a cable that needs to be connected to the server board.
AF000099
Figure 6. Active Heat Sink (Cable Not Shown)
Use the following steps to install a heat sink.
1. Set the heat sink over the processor, lining up the four captive screws with the four posts
surrounding the processor.
2. Loosely screw in the captive screws on the heat sink corners in the order shown by Figure 7.
Do not fully tighten one screw before loosely attaching the others.
3. In the same order, gradually and equally tighten each captive screw until each is firmly
tightened. Do not fully tighten one screw at a time.
Figure 7. Installing Heat Sink (Passive Heat Sink Shown)
4. Active heat sink only: Connect the heat sink cable to the server board. Reference you board
documentation for proper fan header location.
5. Reinstall and reconnect any parts you removed or disconnected to reach the processor sockets.
See the documentation that came with your chassis for instructions on installing chassis
components.
6. Replace the chassis cover and reconnect the AC power cord. See the documentation that came
with your chassis for instructions on installing the cover.
Other manuals for 5000 Series
1
Table of contents
Other Intel Computer Hardware manuals
Intel
Intel EP80579 User manual
Intel
Intel 486MIS User manual
Intel
Intel RS3FC044 User manual
Intel
Intel SBC 711 Quick user guide
Intel
Intel FCPGA2 - Processor - 1 x Pentium 4 2.66 GHz Instruction Manual
Intel
Intel RS25AB080 User manual
Intel
Intel 7512 Instruction Manual
Intel
Intel 2ND GENERATION INTEL CORE PROCESSOR FAMILY MOBILE - SPECIFICATION UPDATE... User manual
Intel
Intel Enpirion EM2COMIF User manual
Intel
Intel SL8J6 - Pentium 4 Processor User manual
Intel
Intel BV80605001914AG - Processor - 1 x Xeon X3430 User manual
Intel
Intel 8XC251SA Guide
Intel
Intel U3-1L User manual
Intel
Intel Compute Module MFS2600KI User manual
Intel
Intel RS2PI008 User manual
Intel
Intel 440GX Guide
Intel
Intel l2ICE User manual
Intel
Intel core i5 X series User manual
Intel
Intel Xeon E3-1125C User manual
Intel
Intel iAPX 86 User manual
Popular Computer Hardware manuals by other brands
EMC2
EMC2 VNX Series Hardware Information Guide
Panasonic
Panasonic DV0PM20105 Operation manual
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 user manual
Gigabyte
Gigabyte B660M DS3H AX DDR4 user manual
Raidon
Raidon iT2300 Quick installation guide
National Instruments
National Instruments PXI-8186 user manual
