Intamsys FUNMAT PRO 310 User manual
3D Printer User Manual
FUNMAT PRO 310
Engineering Materials | Desktop Industrial Grade
I
Contents
1 Service and Support ............................................................................................................................1
1.1 Service........................................................................................................................................1
1.2 Safety Instructions......................................................................................................................1
1.2.1 Hazard type .....................................................................................................................1
1.2.2 Areas with potential safety hazard...................................................................................2
1.2.3 Safety door lock ..............................................................................................................3
1.2.4 Environmental requirements ...........................................................................................4
2 Setting and Installation .......................................................................................................................1
2.1 General Information ...................................................................................................................1
2.1.1 Tools that come with the printer ......................................................................................1
2.1.2 Prepare relevant equipment for installation.....................................................................1
2.1.3 Check the printer nameplate............................................................................................5
2.2 Printer Preparation......................................................................................................................5
2.2.1 Unpack ............................................................................................................................5
2.2.2 Remove accessories.........................................................................................................6
2.2.3 Unbuckle X-axis and Y-axis............................................................................................6
2.2.4 Startup .............................................................................................................................7
2.2.5 Installation of Printing Build Plate..................................................................................8
3 System Components ............................................................................................................................9
3.1 Printer Overview ........................................................................................................................9
3.2 Top Door and User Operation Interface ...................................................................................10
3.3 Printing Chamber Components ................................................................................................ 11
3.4 Independent Filament Box ....................................................................................................... 11
3.5 X/Y Axis Components..............................................................................................................13
3.6 Z-axis Components...................................................................................................................16
3.7 Hot Bed Components ...............................................................................................................17
4 User Interface.....................................................................................................................................18
4.1. Overview .................................................................................................................................18
4.1.1 Status bar.......................................................................................................................18
4.1.2 Navigation bar...............................................................................................................19
4.1.3 Display area...................................................................................................................20
4.2 Main Interface ..........................................................................................................................20
4.2.1 Loading print files .........................................................................................................21
4.2.2 Main status area.............................................................................................................22
4.2.3 Auxiliary status area ......................................................................................................23
4.2.4 Control area...................................................................................................................23
4.3 Queue .......................................................................................................................................24
4.4 Materials...................................................................................................................................25
4.4.1 Material selection ..........................................................................................................26
II
4.4.2 Material loading ............................................................................................................27
4.4.3 Material unloading ........................................................................................................28
4.4.4 Material database management .....................................................................................29
4.5 Tools .........................................................................................................................................31
4.5.1 Axis control ...................................................................................................................32
4.5.2 Calibration.....................................................................................................................33
4.5.3 Parameter Settings.........................................................................................................43
4.6 Settings .....................................................................................................................................44
4.6.1 Device information........................................................................................................ 44
4.6.2 Wireless network settings..............................................................................................45
4.6.3 Wired network settings..................................................................................................46
4.6.4 Camera settings .............................................................................................................46
4.6.5 Remote print..................................................................................................................47
4.6.6 Motor enabling ..............................................................................................................48
4.6.7 Screen lock password settings .......................................................................................49
4.7 Other Interfaces ........................................................................................................................50
4.7.1 Warning prompt.............................................................................................................50
4.7.2 Resume print .................................................................................................................50
4.7.3 Command line ...............................................................................................................51
5 Operate Printer..................................................................................................................................52
5.1Startup and Shutdown of Device ...............................................................................................52
5.1.1 Power on the printer ......................................................................................................52
5.1.2 Power off the printer .....................................................................................................53
5.2 Preparation of Print Materials ..................................................................................................53
5.3 Nozzle Replacement and Material Change .............................................................................. 56
5.3.1 Nozzle Replacement......................................................................................................56
5.3.2 Material change before printing ....................................................................................57
5.3.3 Pause to change material ...............................................................................................57
5.3.4 Supply filament after out-of-material warning..............................................................58
5.4 Basic Printing Operations......................................................................................................... 58
5.4.1 Prepare printer...............................................................................................................58
5.4.2 Import print file to the printer........................................................................................59
5.4.3 Load the print file..........................................................................................................60
5.4.4 Printing process.............................................................................................................61
5.4.5 Printing parameter settings............................................................................................62
5.4.6 Printing alarm................................................................................................................63
5.4.7 Pause printing................................................................................................................63
5.4.8 Stop printing..................................................................................................................64
5.4.9 After completion of printing..........................................................................................64
5.4.10 Locking of front door and top cover............................................................................ 65
5.5 Printer Status ............................................................................................................................66
5.5.1Temperature status..........................................................................................................66
5.5.2 Software version............................................................................................................66
III
6 Maintenance.......................................................................................................................................67
6.1 Inspection Before Each Printing...............................................................................................67
6.1.1 Inspect the printing platform .........................................................................................67
6.1.2 Clean the printing chamber ........................................................................................... 67
6.1.3 Inspect the nozzle .......................................................................................................... 67
6.2 Maintenance after Each Printing ..............................................................................................68
6.2.1 Clean the printing build plate ........................................................................................68
6.2.2 Clean the nozzle ............................................................................................................ 68
6.2.3 Clean the chamber.........................................................................................................68
6.3 Regular Maintenance................................................................................................................68
6.3.1 Clean feeding gears of the extruder...............................................................................68
6.3.2 Maintenance of moving parts ........................................................................................69
6.3.3 Maintenance of chamber filter ...................................................................................... 71
6.3.4 Maintenance and Replacement of Feeding Pipe............................................................71
6.4 Others .......................................................................................................................................73
7 Trouble shooting ................................................................................................................................ 74
IV
Record of Modification and Version Description
Version
Time
Description
E01
July 2023
First version of the Manual
1
1 Service and Support
This chapter provides information on the service and support of FUNMAT PRO 310 desktop
industrial grade 3D printers (hereinafter referred to as "FUNMAT PRO 310", the "printer", the
"machine" or the "device"), as well as safety information and location of safety labels.
1.1 Service
If you have any questions not covered in this manual during the use of the printer, please contact
INTAMSYS Customer Support:
Region
Email
Asia-Pacific
Support_AP[email protected]om
Europe, Middle East and Africa
Support_EME[email protected]om
America
Support_America@intamsys.com
1.2 Safety Instructions
The following basic security tips are intended to ensure safe installation, operation, and maintenance
of INTAMSYS equipment, and shall not be considered as comprehensive safety issues. The machine
is a safe and reliable industrial grade 3D printer. Make sure to inspect for and eliminate potential
hazards, if any, in the printer area before using this printer.
1.2.1 Hazard type
INTAMSYS recommends that all services be provided by qualified personnel. All personnel who
operate this printer or are near it shall understand the meaning of the following hazard classification
signs used in this manual.
[High Voltage Warning]: It indicates that high voltage exists. Keep away from
exposed circuits, and it is recommended to remove all ornaments.
[High Temperature Warning]: It indicates a high printer temperature. Be
cautious when working near components that are exposed to heat. Always wear
the safety gloves that come with the printer.
The temperature of the print head in the printer can reach up to 300℃.
The temperature of the printing platform in the printer can reach up to
160°C.
The temperature in the chamber of the printer can reach up to 100°C.
[Pinching Warning]: It indicates that your hands might be pinched between two
objects. One or more objects are moving in your working area.
2
Please note that changes or modifications without the approval of the responsible party for
compliance may invalidate the user's permission to operate the device.
The device complies with Part 15 of the FCC Rules and the Industry Canada License-exempt
RSS Standard. The following two conditions should be met for operation:
1. The device may not cause harmful interference;
2. The device must accept any interference received, including interference that may lead to
undesired operation.
The device complies with the radiation exposure limits of FCC/IC RSS-102 for uncontrolled
environment. The device shall be installed and operated at a minimum distance of 20 cm from
the radiator and the operator.
1.2.2 Areas with potential safety hazard
The following components and areas have been highlighted as with potential hazards. Failure to
follow the safety regulations might cause system faults or reliability issues.
Extruder
[High Temperature Warning]: Make
sure to wear safety gloves if it is
necessary to maintain the extruder or
work inside the chamber when the
extruder is heated.
Printing platform
[High Temperature Warning]: Make
sure to wear safety gloves if it is
necessary to remove the printing build
plate of the platform or work inside the
chamber when the hot bed is high in
temperature.
Chamber
[High Temperature Warning]: Make
sure to wear safety gloves if you work
inside the chamber at medium and low
temperatures during heating; it is not
recommended to work in the chamber
at high temperatures.
3
XY motion frame
[Pinching Warning]: Do not wear tie,
loose clothing, or hanging ornaments
when working near a moving printer
component.
[Pinching Warning]: Do not click
HOME when there is a model on the
platform.
[Pinching Warning]: Be careful when
maintaining this moving component.
Z-axis motion frame
[Pinching Sign]: Do not wear tie, loose
clothing, or hanging ornaments when
working near a moving printer
component.
[Avoid Collision]: If there is a printed
model on the platform, be care to raise
the platform to a proper height to
prevent puncturing the organ cover;
[Avoid Collision]: If there is an object
under the platform, be care to lower
the platform to a proper height to
prevent deformation of drive rod parts
and leveling failure caused by
platform collision.
1.2.3 Safety door lock
Sensors are used to monitor the status of the chamber front door and printer top cover. For the
purpose of safety, the chamber door and top cover shall be closed before the XYZ motor can start
working. The electromagnetic lock ensures that the chamber door and top cover remain securely
closed during printing.
Fig. 1.1 Safety Door Lock
Front door sensor
Electromagnetic lock
4
1.2.4 Environmental requirements
The printer is for indoor use only.
Air quality conditions (conductive or non-conductive) with excessive solid particles
might cause damage to the system.
The printer shall operate between 15°C and 30°C (59°F to 86°F) with a relative humidity
range of 30% to 70% (non-condensing).
The printer storage temperature shall be between 0°C and 35°C (32°F to 95°F) with a
relative humidity range of 20% to 90% (non-condensing).
1.2.5 Statement
ce matériel est conforme aux limites de dose d'exposition aux rayonnements, FCC / CNR-102
énoncée dans un autre environnement.cette eqipment devrait être installé et exploité avec distance
minimale de 20 entre le radiateur et votre corps.
1
2 Setting and Installation
This chapter describes the basic settings and installation of FUNMAT PRO 310.
2.1 General Information
2.1.1 Tools that come with the printer
Please check the packing list that comes with the printer. These tools include common tools required
for printer maintenance and various spare parts.
2.1.2 Prepare relevant equipment for installation
The guide for preparation of installation site ensures that relevant equipment for printer installation
can be prepared effectively and safely.
Fig. 2.2 Space required for installation and maintenance (Unit: mm)
Other manuals for FUNMAT PRO 310
1
Table of contents
Other Intamsys 3D Printer manuals
Intamsys
Intamsys FUNMAT PRO User manual
Intamsys
Intamsys FUNMAT PRO User manual
Intamsys
Intamsys Funmat Pro 410 User manual
Intamsys
Intamsys Funmat Pro 410 User manual
Intamsys
Intamsys Funmat Pro 410 User manual
Intamsys
Intamsys FUNMAT HT User manual
Intamsys
Intamsys FUNMAT HT User manual
Intamsys
Intamsys FUNMAT PRO 310 User manual
Intamsys
Intamsys FUNMAT HT User manual
