InFocus LP260 Instruction manual
LP260 RS-232 Connection
The LP260 requires the serial control cable (part # 210-0203-xx) that comes with the projector.
Command Format
All commands consist of 3 alpha characters followed by a request, all enclosed in parentheses. The request can be a read request
(indicated by a "?") or a write request (indicated by 1 to 4 ASCII digits).
A read request example:
(AAA?) where
( starts the command
AAA denotes the command
? denotes the read request
) ends the command
A read command returns the range and the current setting, for example:
Read Command Examples
Function Command Response
Brightness (BRT?) (0-22, 10)
Volume (VOL?) (0-80, 0)
Lamp Hours (LMP?) (0-9999, 421)
A write request example:
(AAA####) where
( starts the command
AAA denotes the command
#### denotes the value to be written
(leading zeros not necessary)
) ends the command
Some commands have ranges, while others are absolute. If a number greater than the maximum range is received, it is
automatically set to the maximum number for that function. If a command is received that is not understood, a "?" is returned. With
absolute settings, "0" is off, 1-9999 is on. The one exception is the Power command, where 0 is off and 1 is on.
To assure the projector can process a command, wait 3 seconds before entering the next command.
Write Command Examples
Function Command Response
Brightness (BRT10) Sets the brightness
to 10
Freeze (FRZ1) or
(FRZ8888) Freezes the display
Power (PWR0) Turns power off
Power (PWR1) Turns power on
Error Conditions
Not all commands are supported for all projectors. If an unsupported command is issued, the command will be ignored. If a
command is received that is not understood, a ‘?’ character will be returned indicating the command was not understood.
Limitations
The CLI cannot respond to commands coming in at a high-rate. Therefore, a delay must occur between commands to ensure that
the command gets properly executed. To assure the projector can process a command, wait 3 seconds before entering the next
command.
LP260 RS-232/CLI Values
The following table lists the RS-232 command value ranges for controlling the LP260 projector.
Note: Specified commands and values apply to the LP260 with version 7.3 software or higher. Command values for LP260s with
earlier software versions may vary. If your LP260 does not have version 7.3 software or higher, go to the Software/Downloads
page to download and upgrade the projector software.
Note: The LP 260 requires a 9-pin DIN to a standard 15-pin serial connection available from most computer stores.
Source Independent Settings
Function/Setting CLI
Command REMARK
POWER ON C00
FORCED POWER OFF C01 POWER OFF with "POWER
OFF?"
POWER OFF C02 "POWER OFF?" and then
POWER OFF
VOLUME + C09 Same function as RC
VOLUME - C0A Same function as RC
SOUND MUTE ON C0B
SOUND MUTE OFF C0C
MENU ON C1C
MENU OFF C1D
POINTER RIGHT C3A Same function as key on the
set
POINTER LEFT C3B Same function as key on the
set
POINTER UP C3C Same function as key on the
set
POINTER DOWN C3D Same function as key on the
set
ENTER C3F Same function as key on the
set
FREEZE ON C43
FREEZE OFF C44
FINE SYNC + C49 Same function as RC
FINE SYNC - C4D Same function as RC
ZOOM C80 Same function as RC
FOCUS C87 Same function as RC
Other manuals for LP260
4
Other InFocus Projector manuals
InFocus
InFocus LP340B User manual
InFocus
InFocus in2100 Series User manual
InFocus
InFocus IN112x User manual
InFocus
InFocus LP755 User manual
InFocus
InFocus LP500 User manual
InFocus
InFocus Learn Big IN5102 User manual
InFocus
InFocus SP5700 User manual
InFocus
InFocus INV30 User manual
InFocus
InFocus LP 820 User manual
InFocus
InFocus IN119HDxa User manual
InFocus
InFocus LP130 User manual
InFocus
InFocus LP340 User manual
InFocus
InFocus LP770 User manual
InFocus
InFocus LP800 Parts list manual
InFocus
InFocus ScreenPlay 5700 User manual
InFocus
InFocus IN124STA User manual
InFocus
InFocus ScreenPlay 7205 User manual
InFocus
InFocus X1 User manual
InFocus
InFocus IN2124a User manual
InFocus
InFocus SP4800 User manual
