InFocus IN72 Guide

29

Maintenance

Cleaning the lens

1Apply a non-abrasive camera lens cleaner to a soft, dry cloth.

• Avoid using an excessive amount of cleaner, and don’t apply the

cleaner directly to the lens. Abrasive cleaners, solvents or other harsh

chemicals might scratch the lens.

2Lightly wipe the cleaning cloth over the lens in a circular motion.

Replacing the projection lamp

The lamp hours timer in the Service Info menu counts the number of hours

the lamp has been in use. Twenty hours before the lamp life expires, a mes-

sage appears on the screen at startup indicating that you should change the

lamp. The LED on top of the projector also blinks red twice to indicate that

the lamp should be changed.

NOTE: You can order new lamp housings from www.infocus.com (in select

areas), your retailer or your dealer. Use only a replacement lamp with the

same type and rating as the original lamp.

1Turn off the projector and unplug the power cord. If ceiling mounted,

disconnect all cables and detach the projector from the ceiling mount.

2Wait 60 minutes to allow the projector to cool thoroughly.

3Turn the projector upside down on a soft cloth so that the lamp door is

facing you. Remove the base or ceiling mount plate, if attached, by

removing the 3 screws.

Lamp hours used

wait 60 minutes

turn off and unplug

projector

30

4Push the 2 tabs on the lamp door toward the front of the projector and

lift the lamp door off.

5Loosen the three captive screws that attach the lamp housing to the pro-

jector.

6Detach the lamp connector from the projector by depressing the locking

tab on the connector and lightly pulling it free.

WARNING:

To avoid burns, allow the projector to cool for at least 60 minutes

before you replace the lamp.

Be extremely careful when removing the lamp housing. In the

unlikely event that the bulb ruptures, small glass fragments may be

generated. The lamp housing is designed to contain these frag-

ments, but use caution when removing the lamp housing. Before

replacing the lamp, clean the lamp compartment and dispose of

cleaning materials. Wash hands after lamp replacement. This prod-

uct has a lamp which contains a very small amount of mercury. Dis-

pose of it as required by local, state or federal ordinances and

regulations. For more information see www.eiae.org.

7Carefully remove the lamp housing. Dispose of the lamp in an environ-

mentally proper manner.

8Install the new lamp housing and tighten the screws.

9Re-attach the lamp connector to the projector. The locking tab should

engage when the connector is fully plugged in.

lamp door

lamp

housing

lamp

connector

captive screws

31

10 Replace the lamp door.

11 Replace the base or ceiling mount plate, if necessary.

12 Plug in the power cord and press the Power button on the remote or

keypad to turn the projector back on.

13 To reset the lamp hour timer, navigate to the Settings>Service menu

and select Reset Lamp Hours. See page 28 for details.

Service menu

Other manuals for IN72

6

This manual suits for next models

2

Table of contents

Popular Projector manuals by other brands

iEmmet

iEmmet MP-312 user manual

Epson

Epson VS400 Specifications

Sony

Sony VPL-HS10 Marketing Specifications & Features manual

Sony

Sony VPL-HW65ES Quick reference manual

Toshiba

Toshiba TLP-791U Specifications

Philips

Philips LC1341 Declaration of conformity

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB operating instructions

NEC

NEC NP600S EDU Specifications

BenQ

BenQ SH753P user manual

Eiki

Eiki EK-623U series quick start guide

Epson

Epson PowerLite Pro Cinema 6020UB user guide

Epson

Epson PowerLite Home Cinema 705HD user guide

Christie

Christie LHD700 user manual

Navitar

Navitar FX instruction manual

Sony

Sony SRX-R815P operating instructions

Vivitar

Vivitar DP1500 X specification

Acer

Acer C20 Series manual

Asus

Asus ZenBeam Latte user manual