Imi Heimeier Wireless Air Sensor User manual
Wireless Air Sensor
Funkbasierter
Lufttemperatursensor
Capteur de température
d’air sans fil
2
3
Table of contents/Inhaltsverzeichnis/
Table des matières
EN
Introduction .................................... 4
Installation ...................................... 6
Pairing ............................................ 8
Removing/reset .............................. 9
Replacing the battery...................... 9
DE
Einführung.................................... 10
Installation .................................... 12
Gerät koppeln............................... 14
Entfernen/Zurücksetzen................ 15
Batteriewechsel ............................ 15
FR
Introduction .................................. 16
Installation .................................... 18
Appairage..................................... 20
Suppression/réinitialisation............ 21
Remplacement de la pile .............. 21
Notes/Notizen/Notes .................... 22
4
Introduction
Various rooms in the home will reach a desired comfortable level more quickly
than others. In most homes a single thermostat senses the temperature in
one room but controls the entire property, leaving certain rooms either to
warm or not warm enough! By installing the ‘IMI Heimeier Wireless air sensors’
throughout the home, you can calculate and average temperature, thus allowing
for better control which can help to play an important part in reducing energy
consumption.
You can also use a ‘Wireless air sensor’ instead of utilising the on board
temperature sensor within the ‘IMI Heimeier thermostat’*. This is ideal when the
thermostat* is not installed in the desired area for measuring temperature.
* Note: The ‘Wireless air sensor’ will only operate with IMI Heimeier compatible
products. Visit www.imi-hydronic.com for more information.
5
Wireless air sensor
6
Installation
This sensor is designed to be surface mounted.
1. Using a small coin unscrew the battery cover anti-clockwise to release.
Remove the clear plastic tab and replace the battery cover.
2. Pair the sensor to a IMI Heimeier compatible thermostat by holding down on
the pairing button, (see pairing section for details).
3. Apply the double sided adhesive disc to the back of the sensor.
4. Carefully choose a location that is within signal range.
5. Peel o the second side of the adhesive disc and stick to the desired surface
area.
Recommendation
Locate on to a wall at a height of 1.5 meters, not adjacent or directly above the
heat source, e.g. radiators. Avoid direct sunlight and potential draft areas.
Specifications
Operating temperature: 0-35°C
Operating voltage: 3V
Pollution degree: Degree 2
7
1 2
3 4
8
Pairing
• On the ‘Wireless air sensor’, press and hold the pairing button for 5 seconds.
The LED will glow red to indicate pairing status.
If the sensor has successfully paired to your IMI Heimeier compatible device, the
LED indicator will go out after a few seconds.
If pairing is unsuccessful the LED will remain lit for 60 seconds before going o.
At this point, repeat the previous step and try again.
LED indicator Pair/Reset button
9
Removing/reset
Replacing the battery
• Press and hold down the pairing/reset button for 15 seconds on the ‘Sensor/
Switch’. LED indicator will flash 3 times to conrm reset.
At this point the ‘Wireless air sensor’ will notify your IMI Heimeier compatible
device that it has left the system, and will automatically be removed from the
‘Accessory menu’.
• Using a small coin turn the battery cover anti-clockwise to release.
• Remove the battery gently, by releasing the top end rst opposite the
‘Retaining Tab’.
• Install new 3V CR2032 Lithium Cell battery positive side up, by inserting one
end behind the ‘Retaining’ Tab, then push down gently until battery clips into
place.
• Re-locate battery cover and turn clockwise to lock.
Retaining
tab
Release battery from the opening
at the top
CAUTION! RISK OF EXPLOSION IF BATTERY
IS REPLACED BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING
TO THE INSTRUCTIONS.
10
Einführung
Manche Räume in der Wohnung erreichen schneller die eingestellte Temperatur
als andere. In vielen Häusern misst ein zentrales Gerät die Temperatur eines
Referenzraumes, und steuert auf dieser Basis das gesamte Haus. Dies kann
in manchen Räumen zur Unter- oder Überversorgung führen. Durch die
Installation der “IMI Heimeier Wireless Air Sensors” im ganzen Haus können
Sie die aktuelle Durchschnittstemperatur ermitteln und so eine genauere
Heizregelung ermöglichen. Das kann einen wichtigen Beitrag zur Senkung ihres
Energieverbrauchs leisten.
Des Weiteren kann ein funkbasierter Lufttemperatursensor zusätzlich zum
IMI Heimeier Thermostat* zur Temperaturermittlung verwenden werden. Dies
ist ideal, wenn der Thermostat* nicht in dem gewünschten Bereich für die
Temperaturmessung installiert ist.
* Hinweis: Der “ Wireless air sensor “ funktioniert nur mit IMI Heimeier
kompatiblen Produkten. Besuchen Sie www.imi-hydronic.com für weitere
Informationen.
Table of contents
Languages:
