ICON PRO-FORM EASY STRIDER User manual
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Keep this manual
for future reference.
Model No. PFEL04813.0
Serial No.
Write the serial number in the space
above for reference.
Serial Number Decal
USER’S MANUAL
To register your product and
activate your warranty today,
go to www.proformservice.com/
registration.
For service at any time, go to
www.proformservice.com.
Or call 1-888-533-1333
Mon.–Fri. 6 a.m.–6 p.m. MT
Sat. 8 a.m.–12 p.m. MT
Please do not contact the store.
ACTIVATE YOUR
WARRANTY
CUSTOMER CARE
2
TABLE OF CONTENTS
WARNING DECAL PLACEMENT
WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
IMPORTANT PRECAUTIONS..................................................................3
BEFORE YOU BEGIN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
PART IDENTIFICATION CHART. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
HOW TO USE THE ELLIPTICAL ..............................................................14
FCC INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
MAINTENANCE AND TROUBLESHOOTING.....................................................21
EXERCISE GUIDELINES ....................................................................23
PART LIST. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
EXPLODED DRAWING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
ORDERING REPLACEMENT PARTS .................................................. Back Cover
LIMITED WARRANTY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover
This drawing shows the location(s) of the warning
decal(s). If a decal is missing or illegible, see
the front cover of this manual and request a
free replacement decal. Apply the decal in the
location shown. Note: The decal(s) may not be
shown at actual size.
PROFORM is a registered trademark of ICON IP, Inc.
3
WARNING: To reduce the risk of serious injury, read all important precautions and
instructions in this manual and all warnings on your elliptical before using your elliptical. ICON
assumes no responsibility for personal injury or property damage sustained by or through the use of
this product.
1. It is the responsibility of the owner to ensure
that all users of the elliptical are adequately
informed of all precautions.
2. Before beginning any exercise program,
consult your physician. This is especially
important for persons over age 35 or per-
sons with pre-existing health problems.
3. Use the elliptical only as described in this
manual.
4. The elliptical is intended for home use only.
Do not use the elliptical in a commercial,
rental, or institutional setting.
5. Keep the elliptical indoors, away from mois-
ture and dust. Do not put the elliptical in a
garage or covered patio, or near water.
6. Place the elliptical on a level surface, with at
least 3 ft. (0.9 m) of clearance in the front and
rear of the elliptical and 2 ft. (0.6 m) on each
side. To protect the floor or carpet from dam-
age, place a mat under the elliptical.
7. Inspect and properly tighten all parts regu-
larly. Replace any worn parts immediately.
8. Keep children under age 12 and pets away
from the elliptical at all times.
9. The elliptical should not be used by persons
weighing more than 250 lbs. (113 kg).
10. Wear appropriate clothes while exercising;
do not wear loose clothes that could become
caught on the elliptical. Always wear athletic
shoes for foot protection while exercising.
11. Hold the handlebars or the upper body arms
when mounting, dismounting, or using the
elliptical.
12. The heart rate monitor is not a medical
device. Various factors may affect the accu-
racy of heart rate readings. The heart rate
monitor is intended only as an exercise aid
in determining heart rate trends in general.
13. The elliptical does not have a freewheel; the
pedals will continue to move until the fly-
wheel stops. Reduce your pedaling speed in
a controlled way.
14. Keep your back straight while using the ellip-
tical; do not arch your back.
15. Over exercising may result in serious injury
or death. If you feel faint or if you experience
pain while exercising, stop immediately and
cool down.
IMPORTANT PRECAUTIONS
4
STANDARD SERVICE PLANS
5
Thank you for selecting the revolutionary PROFORM®
EASY STRIDER elliptical. The EASY STRIDER
elliptical provides an impressive selection of features
designed to make your workouts at home more effec-
tive and enjoyable.
For your benefit, read this manual carefully before
you use the elliptical. If you have questions after
reading this manual, please see the front cover of this
manual. To help us assist you, note the product model
number and serial number before contacting us. The
model number and the location of the serial number
decal are shown on the front cover of this manual.
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
Heart Rate Monitor
Accessory Tray
Speaker
Handlebar
Upper Body Arm
Pedal
Roller
Track
Console
BEFORE YOU BEGIN
Wheel
Leveling Foot
Length: 5 ft. 8 in. (173 cm)
Width: 2 ft. 2 in. (66 cm)
6
PART IDENTIFICATION CHART
Use the drawings below to identify the small parts needed for assembly. The number in parentheses below each
drawing is the key number of the part, from the PART LIST near the end of this manual. The number following the
key number is the quantity needed for assembly. Note: If a part is not in the hardware kit, check to see if it
has been preassembled. Extra parts may be included.
M8 Locknut
(60)–6
M8 Washer
(63)–6
M4 x 16mm
Screw (56)–4
M10 x 70mm Screw (76)–2
M10 x 60mm Bolt (72)–1
M10 x 53mm Screw (73)–1
M10 x 39mm Screw (75)–2
M8 x 38mm Bolt
(59)–6
M8 x 20mm
Screw (61)–6
M6 Bolt Set (67)–2
M10 Washer
(64)–6
M10 Curved
Washer (62)–2
M10 Split
Washer (80)–2
M10 Locknut
(77)–1
M10 x 20mm
Screw (74)–5
7
2
1
12
76
ASSEMBLY
• To hire an authorized service technician to
assemble this product, call 1-800-445-2480.
• Assembly requires two persons.
• Place all parts in a cleared area and remove the
packing materials. Do not dispose of the packing
materials until you nish all assembly steps.
• Left parts are marked “L” or “Left” and right parts
are marked “R” or “Right.”
• To identify small parts, see page 6.
• In addition to the included tool(s), assembly
requires the following tools:
one Phillips screwdriver
one rubber mallet
Assembly may be easier if you have a set of
wrenches. To avoid damaging parts, do not use
power tools.
1
2. With the help of a second person, place some
of the packing materials (not shown) under the
front of the Frame (1). Have the second per-
son hold the Frame to prevent it from tipping
while you complete this step.
Attach the Front Stabilizer (12) to the Frame (1)
with two M10 x 70mm Screws (76).
Remove the packing materials from under the
Frame (1).
1. Go to www.proformservice.com/registration
on your computer and register your product.
• activates your warranty
• saves you time if you ever need to contact
Customer Care
• allows us to notify you of upgrades and offers
Note: If you do not have Internet access, call
Customer Care (see the front cover of this
manual) and register your product.
8
3
1
74
74
74
11
64
64
75
4
1
2
Wire
Tie
Wire Tie
32
3. With the help of a second person, place some of
the packing materials (not shown) under the rear
of the Frame (1).
Attach the Track (11) to the Frame (1) with four
M10 x 20mm Screws (74), two M10 x 39mm
Screws (75), and six M10 Washers (64) as
shown; start all six Screws, and then tighten
them.
Remove the packing materials from under the
Frame (1).
4. Have a second person hold the Upright (2) near
the Frame (1).
Locate the wire tie in the Upright (2). Tie the
lower end of the wire tie to the Main Wire
Harness (32). Then, pull the upper end of the
wire tie until the Main Wire Harness is routed
through the Upright.
Tip: Secure the Main Wire Harness (32) to the
Upright (2) with the wire tie to prevent it from
falling into the Upright.
9
5
2
1
72
74
73
77
80
80
62
Hexagonal Hole
62
32
6
5. Tip: Avoid pinching the Main Wire Harness
(32). Slide the Upright (2) onto the Frame (1).
Attach the Upright (2) with an M10 x 53mm
Screw (73), an M10 x 20mm Screw (74), two
M10 Split Washers (80), and two M10 Curved
Washers (62) as shown; do not fully tighten
the Screws yet.
Finish attaching the Upright (2) with an M10 x
60mm Bolt (72) and an M10 Locknut (77); do
not fully tighten the Screws yet. Make sure
that the Locknut is in the hexagonal hole.
Grease
Grease
18
2
Avoid pinching
the Main Wire
Harness (32)
6. Insert the Long Axle (18) into the Upright (2) and
center it.
Using a plastic bag to keep your fingers clean,
apply some of the included grease to both ends
of the Long Axle (18).
10
7
59 59
60
Hexagonal
Holes
60
4
6
5
3
7. Identify the Right Upper Body Arm (4) and the
Right Upper Body Leg (5), and orient them as
shown.
Insert the Right Upper Body Arm (4) into the
Right Upper Body Leg (5). Attach the Right
Upper Body Arm with three M8 x 38mm Bolts
(59) and three M8 Locknuts (60); make sure
that the Locknuts are in the hexagonal holes.
Do not fully tighten the Bolts yet.
Attach the Left Upper Body Arm (3) to the
Left Upper Body Leg (6) in the same way.
61
61
44
44
18
63
63
8. Slide the Right Upper Body Arm (4) onto the
right side of the Long Axle (18).
Slide the Left Upper Body Arm (3) onto the left
side of the Long Axle (18).
Tighten an M8 x 20mm Screw (61) with an Axle
Cover (44) and an M8 Washer (63) into each
end of the Long Axle (18) at the same time.
8
3
4
This manual suits for next models
1
Table of contents
Other ICON Elliptical Trainer manuals
ICON
ICON NordicTrack FREESTRIDE TRAINER FS9i User manual
ICON
ICON NordicTrack A.C.T. COMMERCIAL User manual
ICON
ICON NTEL99413.1 User manual
ICON
ICON PRO-FORM CARBON-HIIT H7 User manual
ICON
ICON GOLD'S GYM STIDE TRAINER 550i User manual
ICON
ICON PRO-FORM PRO I500 User manual
ICON
ICON NordicTrack COMMERCIAL 14.9 User manual
ICON
ICON PRO-FORM ENDURANCE 920 E User manual
ICON
ICON Pro-Form 14.0 CE PFEL18010.5 User manual
ICON
ICON NordicTrack AUDIOSTRIDER 990 PRO User manual
ICON
ICON PRO-FORM HYBRID TRAINER User manual
ICON
ICON PRO-FORM CrossTrainer 600 User manual
ICON
ICON PFEL09909.1 User manual
ICON
ICON PRO-FORM Perspective 1000 User manual
ICON
ICON PRO-FORM ENDURANCE 1120 E User manual
ICON
ICON PRO-FORM ZE3 User manual
ICON
ICON PRO-FORM 990 CSE User manual
ICON
ICON NordicTrack C 9.5 User manual
Popular Elliptical Trainer manuals by other brands
Bonn Germany
Bonn Germany Concept 2.2 user manual
Precor
Precor Resolute RSL 620 Assembly guide
NordicTrack
NordicTrack E 9.2 Elliptical HASZNALATI UTASITAS
Vision Fitness
Vision Fitness X6600iNetTV Assembly guide
Matrix
Matrix MX-A5x owner's manual
SportsArt Fitness
SportsArt Fitness ECO-NATURAL Elite E874 owner's manual
