Icom IC-F61-L User manual
INSTRUCTION MANUAL
UHF TRANSCEIVER
iF61-L
P0P1P2P3
i
FOREWORD
READ ALL INSTRUCTIONS carefully and completely before
using the transceiver.
SAVE THIS INSTRUCTION MANUAL— This instruction
manual contains important operating instructions for the IC-F61-L
u h f t r a n s c e i v e r .
This instruction manual includes some functions which are
usable only when they are pre-programmed by your dealer. Ask
your dealer for details.
OPERATING NOTES
• When transmitting with a portable radio, hold the radio in a ver-
tical position with its microphone 5 to 10 centimeters away from
your mouth. Keep the antenna at least 2.5 centimeters from your
head and body.
• If you wear a portable two-way radio on your body, ensure that
the antenna is at least 2.5 centimeters from your body when
transmitting.
Icom, Icom Inc. and Icom logo are registered trademarks of Icom Incorporated
(Japan) in Japan, the United States, United Kingdom, Germany, France, Spain,
Russia and/or other countries.
ii
EXPLICIT DEFINITIONS
WORD DEFINITION
RDANGER! Personal death, serious injury or an explo-
sion may occur.
RWARNING! Personal injury, re hazard or electric shock
may occur.
CAUTION Equipment damage may occur.
NOTE
If disregarded, inconvenience only. No risk
of personal injury, re or electric shock.
iii
Versions of the IC-F61-L which display the “EX” mark-
ing on the serial number seal.
The approval rating for these models are II 2G Ex ib
IIA T3 Gb and II 2D Ex tb IIIC T160°C Db IP67.
WARNING! NEVER charge the BP-227AXD (with/without the
transceiver) in an explosive atmosphere. The optional battery char-
gers are not approved as Intrinsically Safe.
When the transceiver is used in a hazardous area, the BP-227AXD
MUST be attached, either the jack cover or HM-138 MUST be at-
tached to the speaker-microphone connector.
KEEP the transceiver and the BP-227AXD clean to avoid any risk
of ignition due to the build-up of electrostatic charges.
Repair of Icom radios should only be carried out by authorized
Icom distributors. In particular, repair of ATEX approved radios can
ONLY be done by Icom to maintain the intrinsically safe rating.
NEVER attempt to repair an ATEX approved radio. Only Icom has
the repair expertise and procedures to maintain the ATEX approval.
Contact your Icom distributor or authorised dealer for details.
INTRINSIC SAFETY
The equipment can be used without the microphone but with the
jack cover.
iv
The ATEX standard is described on the 94/9/EC sticker (Ex Mark-
ing) and BP-227AXD as below.
BP-227AXD
• DO NOT OPEN WHEN AN EXPLOSIVE ATMOSPHERE MAY
BE PRESENT.
• DO NOT CHARGE THE BATTERY IN HAZARDOUS LOCA-
TION.
* The following illustrations show
the IC-F61-L.
v
PRECAUTIONS
RDANGER! NEVER short the terminals of the battery pack.
RDANGER! Use and charge only specied Icom battery packs
with Icom radios or Icom chargers. Only Icom battery packs are
tested and approved for use with Icom radios or charged with Icom
chargers. Using third-party or counterfeit battery packs or chargers
may cause smoke, re, or cause the battery to burst.
RWARNING! NEVER hold the transceiver so that the an-
tenna is very close to, or touching exposed parts of the body, espe-
cially the face or eyes, while transmitting. The transceiver will per-
form best if the microphone is 5 to 10 cm away from the lips and
the transceiver is vertical.
RWARNING! NEVER operate the transceiver with a headset
or other audio accessories at high volume levels. Hearing experts
advise against continuous high volume operation. If you experience
a ringing in your ears, reduce the volume level or discontinue use.
RWARNING! NEVER operate the transceiver while driving a
vehicle. Safe driving requires your full attention—anything less may
result in an accident.
CAUTION: NEVER connect the transceiver to a power source
other than the BP-227AXD. Such a connection will ruin the trans-
ceiver.
CAUTION: MAKE SURE the exible antenna and battery pack
are securely attached to the transceiver, and that the antenna and
battery pack are dry before attachment. Exposing the inside of
the transceiver to water will result in serious damage to the trans-
ceiver.
DO NOT push the PTT when not actually desiring to transmit.
vi
DO NOT use or place the transceiver in direct sunlight or in areas
with temperatures below –20°C or above +55°C.
The basic operations, transmission and reception of the trans-
ceiver, are guaranteed within the specied operating tempera-
ture range. However, the LCD display may be operate correctly, or
show an indication in the case of long hours of operation, or after
being placed in extremely cold areas.
DO NOT modify the transceiver. The transceiver warranty does
not cover any problems caused by unauthorized modication.
DO NOT use harsh solvents such as benzine or alcohol when
cleaning, as they will damage the transceiver surfaces.
BE CAREFUL! The transceiver will become hot when operating
it continuously for long periods of time.
BE CAREFUL! The transceiver meets IP67* requirements for
dust-tight and waterproof protection. However, once the transceiv-
er has been dropped, dust-tight and waterproof protection cannot
be guaranteed because of possible damage to the transceiver’s
case or the waterproof seal.
* Only when the battery pack and jack cover are attached.
Even when the transceiver power is OFF, a slight current still ows
in the circuits. Remove the battery pack or batteries from the trans-
ceiver when not using it for a long time. Otherwise, the installed
battery pack or batteries will become exhausted, and will need to
be recharged or replaced.
MAKE SURE to turn the transceiver power OFF before connect-
ing the supplied/optional equipment.
vii
TABLE OF CONTENTS
FOREWORD ........................................................................................ i
OPERATING NOTES............................................................................ i
EXPLICIT DEFINITIONS..................................................................... ii
INTRINSIC SAFETY............................................................................iii
PRECAUTIONS................................................................................... v
TABLE OF CONTENTS......................................................................vii
SUPPLIED ACCESSORIES..............................................................viii
1 ACCESSORIES ......................................................................... 1–2
■ Accessory attachments .............................................................. 1
2 PANEL DESCRIPTION ............................................................ 3–11
■ Front, top and side panels .......................................................... 3
■ Function display.......................................................................... 6
■ Programmable function keys ......................................................7
3 CONVENTIONAL OPERATION............................................. 12–18
■ Turning power ON..................................................................... 12
■ Channel selection ..................................................................... 12
■ Call procedure .......................................................................... 13
■ Receiving and transmitting ....................................................... 14
■ Scrambler function.................................................................... 17
■ User Set mode.......................................................................... 18
4 BIIS OPERATION .................................................................. 19–34
■ Default setting........................................................................... 19
■ Receiving a call......................................................................... 20
■ Transmitting a call ..................................................................... 23
■ Receiving a message ............................................................... 26
■ Transmitting a status ................................................................. 29
■ Transmitting an SDM................................................................. 30
■ Position data transmission ........................................................ 31
■ Printer connection..................................................................... 32
■ PC connection .......................................................................... 32
viii
SUPPLIED ACCESSORIES
The following accessories are supplied: Qty.
• Flexible antenna…………………………………………………… 1
• Battery pack ……………………………………………………… 1
• Jack cover ……………………………………………………… 1 set
• Belt clip ………………………………………………………… 1 set
• Function name stickers* (KEY-STICKER)……………………… 1
*
There are no names on the programmable function keys since the func-
tions can be freely assigned to [P0] to [P3], [Red], [ ] and [ ] keys.
Attach the supplied function name stickers above the appropriate
keys for easy recognition of that key’s assigned function.
■ Digital ANI................................................................................. 32
■ Auto emergency transmission .................................................. 33
■ Stun function............................................................................. 33
■ BIIS indication........................................................................... 34
■ Priority A channel selection ...................................................... 34
5 BATTERY CHARGING .......................................................... 35–44
■ Caution ..................................................................................... 35
■ Optional battery chargers ......................................................... 39
6 SPEAKER-MICROPHONE .................................................... 45–46
■ Optional HM-138 description .................................................... 45
■ Attachment................................................................................ 46
7 OPTIONS ............................................................................... 47–48
8 ATEX CAUTIONS................................................................... 49–51
9 CE ................................................................................................ 52
1
1ACCESSORIES
■Accessory attachments
DFlexible antenna
Connect the supplied exible antenna to
the antenna connector.
CAUTION:
• NEVER carry the transceiver by
holding the antenna.
• DO NOT connect the antenna other
than listed on page 47.
• Transmitting without an antenna
may damage the transceiver.
ïJack cover
Attach the jack cover when the optional speaker-microphone is not
used.
When the transceiver is used in a hazardous areas, either the jack
cover or HM-138 must be attached to the connector. Failure to do
this will make the radio ATEX non-compliant and may result in an
accident during use in hazardous areas.
To attach the jack cover:
q Insert the jack cover into the
[SP MIC] connector.
wTighten the screw.
To detach the jack cover:
qRemove the screw with a
phillips screwdriver.
w Detach the jack cover for the
speaker-microphone con-
nection.
q
w
qw
Other manuals for IC-F61-L
1
Table of contents
Other Icom Transceiver manuals
