Icom IC-7200 User manual
When the transceiver is connected to a PC with the
USB cable, the following operations can be performed;
• Remote control operation (CI-V: Icom Communica-
tion Interface-V) by the PC.
• Modulation input from the PC.
• Received audio output to the PC.
Transceiver PC
USB cable
(third party)
NOTE:
•
PC software (third party) may be required. (p. 18)
• The CT-17 ci-vlevel converter is required for re-
mote control operation (CI-V) when the USB cable
is not used. See p. 88 in the IC-7200 instruction
manual for details.
• The transceiver connection may not be recog-
nized by the PC because of the USB cable length.
Using the shorter USB cable as possible is rec-
ommended.
System requirements
The PC which supports the following OS (Operating
System) is required;
•
Microsoft®Windows Vista™
•
Microsoft®Windows®XP
•
Microsoft®Windows®2000
NOTE:
• The USB driver is not supported for Microsoft
®
Windows
®
XP (64 bit).
• Icom is not responsible for whole performance of
the PC that supports above OS.
• In this installation guide, the above OS are de-
scribed as “Windows Vista,” “Windows XP” and
“Windows 2000.”
Item requirements
• USB cable (A-B type/third party)
A type
B type
• PC (with USB 1.1 or 2.0)
• Installed audio player
• PC software (third party)
- See p. 18 for details.
OVERVIEW
USB DRIVER
INSTALLATION GUIDE
Thank you for using the Icom Download Service.
Please read this installation guide before installing the USB driver into your PC that is connected to the IC-7200
with the USB (Universal Serial Bus) cable (third party).
Icom, Icom Inc. and the logo are registered trademarks of Icom
Incorporated (Japan) in the United States, the United Kingdom, Germany,
France, Spain, Russia and/or other countries.
Microsoft, Windows and Windows Vista are either registered trademarks
or trademarks of Microsoft Corporation in the United States and/or other
countries.
All other products or brands are registered trademarks or trademarks of their
respective holders.
1
2
PROCEDURE
Refer to the following steps for the USB driver installation.
Before installing the USB driver, log in as the administrator and quit all applications when Windows is run-
ning.
Overview • System requirements (p. 1)
• Item requirements (p. 1)
Preparing • Before installing the USB driver (p. 3)
Driver installation
• Windows Vista (p. 4)
• Windows XP (p. 6)
• Windows 2000 (p. 9)
COM Port Confirmation • Windows Vista (p. 12)
• Windows XP/Windows 2000 (p. 12)
Driver uninstallation • Windows Vista (p. 13)
• Windows XP/Windows 2000 (p. 13)
For your reference
• COM Port setting (p. 14)
• About audio (p. 16)
• Specifications (p. 19)
Precautions
• Before connecting to the PC (p. 2)
• Important (p. 2)
• For IC-PCR1500/IC-PCR2500 user (p. 2)
Before connecting to the PC
The process of connecting the USB cable (third party)
between the transceiver and a PC may differ accord-
ing to your OS.
See the “Driver installation” on pgs. 4 to 11 for details.
• After the driver installation is completed, the USB
cable can be connected regardless of the OS.
• The USB driver installation is required for each unit,
because of the COM port number difference.
Important
• Audio from the USB port may cut out or audio con-
trol with the PC software may get late because of
the PC performance (including OS, environment,
etc.)
• Audio from the USB port may cut out when the CPU
load increases.
• The audio device settings of OS may be changed
when the transceiver is connected to the PC.
• Icom is not responsible for proper operation when
connecting the transceiver and the PC through an
USB hub.
For IC-PCR1500/IC-PCR2500 user
• USB driver on the supplied CD
The file that is included on the supplied CD with
the IC-PCR1500/IC-PCR2500 is the same as the
download file from Icom HP. So, the USB driver in-
stallation can also be performed with the supplied
CD.
•USB driver uninstallation
If the USB driver uninstallation is performed, the
connected unit (when the USB driver is installed) or
IC-PCR1500/IC-PCR2500 cannot be used.
• USB driver re-installation
The USB driver installation is required for each
unit, because of the COM port number difference.
See the IC-PCR1500/IC-PCR2500 instruction man-
ual when installing the USB driver with the supplied
CD.
PRECAUTIONS
3
Before installing the USB driver
Icom HP gives the USB driver download service.
Before installing the USB driver, download the follow-
ing compressed file.
• USB driver
(File name: 7200UsbDrv_v100.zip)
Icom is not responsible for any damage or lack of
data resulting from the use of the USB driver.
PREPARING
4
Windows Vista
DRIVER INSTALLATION
The displayed dialogue boxes, indications or oper-
ations may differ slightly from the following instruc-
tions according to your system conditions or envi-
ronment.
q
Make sure that the transceiver is not connected to
the PC.
w Start up Windows.
• Quit all other application if running.
e Double-click the “WinVista” folder.
• The folder construction: “7200UsbDrv_v100” ➞
“Driver” ➞“WinVista”
Double click
r Double-click the “CP210xVCPInstaller.exe” to start
up the USB driver installer.
Double click
t“A program needs your permission to continue” dia-
logue box appears as below.
Click [Continue].
Click
yVerify the installation location, then click [Install].
Click
uWindows starts scanning for the system, then starts
installing the USB driver.
iAfter the installation is completed, click [OK].
• Restarting the PC is recommended.
Click
NOTE:
• NEVER connect the transceiver to the PC with the USB cable (third party) until the USB driver installation
has been completed.
• The USB driver for Windows Vista does not support the automatic recognition system.
☞Continues to the next page
5
oAfter restarting the PC, connect the transceiver to
the PC with the USB cable (third party) as shown
below.
• Be sure to connect the USB cable correctly and not up-
side down.
Transceiver
PC
USB cable
(third party)
To USB jack
To USB port
Type A
Type B
ACC KEY SEND ALC
REMOT E
!0 Turn the transceiver power ON.
• “Installing device driver software” appears as below.
!1 After the dialogue appears as below, USB driver
installation has been completed.
Windows Vista (Continued)
DRIVER INSTALLATION
6
The displayed dialogue boxes, indications or oper-
ations may differ slightly from the following instruc-
tions according to your system conditions or envi-
ronment.
q
Make sure that the transceiver is not connected to
the PC.
w Start up Windows.
• Quit all other application if running.
eConnect the transceiver to the PC with the USB
cable (third party) as shown below.
• Be sure to connect the USB cable correctly and not up-
side down.
Transceiver
PC
USB cable
(third party)
To USB jack
To USB port
Type A
Type B
ACC KEY SEND ALC
REMOT E
r Turn the transceiver power ON.
• “Found New Hardware” appears as below.
t The “Welcome to the Found New Hardware Wizard”
will come up as below.
Select “No, not this time,” then click [Next>].
Click
Select
y Select “Install from a list or specific location
(Advanced),” then click [Next>].
Click
Select
u Select “Search for the best driver in these locations.”
then select “Include this location in the search,” and
click [Browse].
Click
Select
Select
Windows XP
DRIVER INSTALLATION (Continued)
NOTE:
BE SURE to connect the transceiver to the PC with the USB cable (third party) before installing the USB
driver.
☞Continues to the next page
7
Windows XP (Continued)
DRIVER INSTALLATION
i Select the “Win” folder, then click [OK].
• The folder construction: “7200UsbDrv_v100” ➞
“Driver” ➞“Win”
Click
Select
oClick [Next>].
Click
!0 The Wizard starts searching for the driver and
shows the dialogue below during search.
!1 After the driver is found, the “Hardware Installation”
dialogue box appears as below.
Click [Continue Anyway] to start the installation.
Click
!2 Windows starts installing the USB driver.
!3 After the installation is completed, click [Finish].
Click
!4
After clicking [Finish], the dialogue appears as below.
!5 The “Welcom to the Found New Hardware Wizard”
will come up again to install the USB serial port
driver.
Select “No, not this time,” then click [Next>].
Click
Select
☞Continues to the next page
8
!6 Select “Install from a list or specific location
(Advanced),” then click [Next>].
Click
Select
!7 Select “Search for the best driver in these locations.”
then select “Include this location in the search:”,
and click [Browse].
Click
Select
Select
!8 Select the “Win” folder, then click [OK].
• The folder construction: “7200UsbDrv_v100” ➞
“Driver” ➞“Win”
Click
Select
!9 Click [Next>].
Click
@0 The Wizard starts searching for the driver and
shows the dialogue below during search.
@1 After the driver is found, the “Hardware Installation”
dialogue box appears as below.
Click [Continue Anyway] to start the installation.
Click
@2 Windows starts installing the USB driver.
@3 After the installation is completed, click [Finish].
Click
@4
After clicking [Finish], the dialogue appears as below.
• Restarting the PC is recommended.
Windows XP (Continued)
DRIVER INSTALLATION
9
The displayed dialogue boxes, indications or oper-
ations may differ slightly from the following instruc-
tions according to your system conditions or envi-
ronment.
q
Make sure that the transceiver is not connected to
the PC.
w Start up Windows.
• Quit all other application if running.
eConnect the transceiver to the PC with the USB
cable (third party) as shown below.
• Be sure to connect the USB cable correctly and not up-
side down.
Transceiver
PC
USB cable
(third party)
To USB jack
To USB port
Type A
Type B
ACC KEY SEND ALC
REMOT E
r Turn the the transceiver power ON.
• “Found New Hardware” appears as below.
tThe “Found New Hardware Wizard” will come up as
below.
Click [Next>].
Click
ySelect “Search for a suitable driver for my device
(recommended),” then click [Next>].
Click
Select
uSelect “Specify a location,” then click [Next>].
Click
Select
iClick [Browse...].
Click
Windows 2000
DRIVER INSTALLATION (Continued)
NOTE:
BE SURE to connect the transceiver to the PC with the USB cable (third party) before installing the USB
driver.
☞Continues to the next page
10
Windows 2000 (Continued)
DRIVER INSTALLATION
oSelect “slabbus.inf” in the “Win” folder, then click
[Open].
• The folder construction: “7200UsbDrv_v100” ➞
“Driver” ➞“Win”
Select
“slabbus.inf”
Click
!0 Click [OK].
Click
!1 When the driver is found, the following dialogue is
displayed.
Click [Next>] to start the installation.
Click
!2 After the installation is completed, click [Finish].
Click
!3 The “Found New Hardware Wizard” appears again.
Click [Next>].
Click
!4 Select “Search for a suitable driver for my device
(recommended),” then click [Next>].
Click
Select
!5 Select “Specify a location,” then click [Next>].
Click
Select
☞Continues to the next page
Other manuals for IC-7200
6
Table of contents
Other Icom Transceiver manuals
