icetro ISI-163SB User manual

ISI-163SB
● This product is for indoors, so do not use it outdoors.
● Before using the product, be fully familiar
with the contents in the manual.
Please store this manual in a place where you can
reach it easily for future reference.
● This user manual contains a product warranty.
● This appliance can be used by children aged
from 8 years and above and persons with reduced
physical, sensory or mental capabilities or lack
of experience and knowledge if the have been given
supervision or instruction concerning use of the
appliance a safe way and understand the hazards
involved.
Children should be supervised to ensure
that they do not play with the appliance.

2
Dear customers;
Contents
Acknowledgment
Method of Use
Cautions for your safety
- Power supply related items
- Installation related items
- During use
Part names and controllers
3~4
4
5
6~7
8
9
10
11
11
12
Check prior to use
Button display names and functions
How to make soft ice cream
Conversion function between
ice-cream mode and yogurt mode
How to set non-load
Carburetor control
Thank you very much for purchasing a soft ice cream maker made by ICETRO. For correct use of the
product and its maintenance, please read this manual carefully. If a problem occurs while using the
product, you can refer to this manual for troubleshooting. This manual contains a product warranty, so
keep it safely for future reference. This product can be installed only by someone qualified for installation.
If use of parts and accessories not provided or approved by ICETRO or any part or accessories made
by ICETRO but remodeled by other person causes a problem, we are not responsible for it financially.
(The functions and specifications shown in this manual and on the web site are subject to change
without notice. Please visit our website at http://www.icetro.com to obtain the latest specifications.
Cleaning Method
13~14
1 5
15
16
17
Cleaning Method
- Wash mode
- Washing of each parts
-
Condenser and filter cleaning method
Dasher cover assembly method
-
Dasher cover assembly
-
Dasher and dasher cover
ETC
18
19
20
21
22
23
24~27
28
29
Installation method
- Electrical connection
B e f o r e r e q u e s t i n g s e r v i c e
Error code types
Circuit diagram
Product specification
Refrigerant circuit
Part list
What to watch out for
Warranty

3
Cautions for your safety

4
30

5

6
Part names and controllers
FRONT
BACK SIDE
510
510
820
741
635592193 50
745
1470
BUTTON
DISPLAY
SIDE PANEL
FILTER
CONDENSER
MIXING TANK
COVER
POWER
SWITCH
DRAIN BOX
DASHER COVER
STAR
DASHER COVER
BOLT
LEVER

7
Included accessories
DASHER LUG FOAM
4EA
HINES
1EA
CARBURETOR TUBE
2EA
CARBURETOR TUBE
BODY
2EA
BRUSH
1EA
BRUSH 3
1EA
BRUSH 143
1EA
MANUAL
1EA
PATITION FOOD
2EA
BEARING DASHER
2EA
PACKING DOWN 143
2EA
PACKING PISTON
2EA
PACKING CARBURETOR
4EA
DASHER COVER PACKING
2EA
PACKING REMOVE HANDLE
1 EA

8
■ Make sure to check them prior to use ! ■
Install it independently with an earth leakage circuit breaker with more than 30 A
and provide anexternal grounding.
(Ask a qualified electrical technician for the installation.)
The power cable should be connected before the product can operate normally.
If you intend to leave it unused for a long time, wash it and turn off the water
supply valve and turn off the earth leakage circuit breaker.
The air suction and discharge should be facilitated so that the cooling
performance can be optimized.
If you leave it open, bugs or contaminants may enter the mixing tank.
It is recommended to clean the cylinder, the mixing tank, the impeller,
the dasher, and the piston every day.
Clean the condenser at least once a month or more often.
The cylinder, mix tank, impeller, dasher, and piston inside the product make
contact with the ingredients, so you should clean them once every day.
This product is exclusively for 1Ø, 230 V~, 50 Hz / 220 V~, 60 Hz
■ Do not block the air vent.
■ Close the mixing tank.
■ Clean the condenser once a month.
■ Clean it at least once a day.
■ Clean the filter once a week.
Check prior to use
information
For your

9
Button display names and functions
③ “
FREEZING CONTROL LEVEL
”
BUTTON
Lamp blinks when there
are insufficient ingredients
and It blinks when there
is no ingredient.
Icecream Level Adjustment button
② “MIX LOW”
Display the ingredient
temperature inside the
hopper.
① “MIX TANK TEMPERATURE”
It is used to store ingredients.
④ “MIX REF” BUTTON
Turned on while the raw material in the
cylinder and the hopper is being
refrigerated
⑤ “STAND-BY” BUTTON
Button is used to wash.
It turns the dasher motor and the
impeller (applied model) in the tank.
⑥ “WASH” BUTTON
Button is used to make soft freezer.
⑦ “AUTO” BUTTON

10
How to make soft ice cream
1. Open the top cover and pour
ingredient into the hopper tank.
Please be aware of using soft
serve mix stored under -10℃.
Please check MIX LOW lamp
turns OFF.
2. After pouring the mix, please insert the carburetor body
and carburetor tube into the hole in the hopper.
3. Match carburetor medium-size hole and apply impellers
on the shaft in the hopper.
Carburetor body
Impeller
Medium-size hole Carburetor
Carburetor tube
4. Press AUTO button to start making soft ice cream.
● The smaller the caburator hole is, the higher the overrun (air content) is.
Instead, in case of continuous sales, the ingredients supply gets slower and the soft ice
cream is let out slowly.
● The caburator hole can get clogged, so check it and wash it periodically during use.
● The manufacturer shall not be responsible for any trouble (e.g., spoilage of materials,
overcooling, non-production of ice cream) caused by using materials in non-frozen
state (10℃).
For your
information
Table of contents
Other icetro Freezer manuals


















