IBM ThinkVision L180p User manual
COLOR MONITOR
SERVICE MANUAL
CAUTION
BEFORE SERVICING THE UNIT,
READ THE SAFETY PRECAUTIONS
IN THIS MANUAL.
MODEL: L180p(9180-HB9)
Chassis No. : CL-42
1. LCD CHARACTERISTICS
Type : TFT SXGA LCD
Size : 18.1inch(459.74mm)
Pixel Pitch : 0.2805(H) x 0.2805(V)
Color Depth : 8-bit, 16,777,216 colors
Electrical Interface : LVDS
Surface Treatment : Anti-Glare, Hard Coating (3H)
Operating Mode : Normally Black
Backlight Unit : Six-CCFL (Cold Cathode
Fluorescent Lamp)
2. OPTICAL CHARACTERISTICS
2-1. Viewing Angle by Contrast Ratio
≥
10
Left : -60° min., -85°(typ)
Right : +60° min., +85°(typ)
Top : +60° min., +85°(typ)
Bottom : -60° min., -85°(typ)
2-2. Luminance : 200(min), 250(typ)
2-3. Contrast Ratio : 250(min), 400(typ)
3. SIGNAL (Refer to the Timing Chart)
3-1. Sync Signal
• Type : Separate, Composite,
SOG (Sync On Green)
Digital
3-2. Video Input Signal
1) Type : R, G, B Analog
2) Voltage Level : 0~0.71 V
a) Color 0, 0 : 0 Vp-p
b) Color 7, 0 : 0.467 Vp-p
c) Color 15, 0 : 0.714 Vp-p
3) Input Impedance : 75 Ω
3-3. Operating Frequency
Analog
Horizontal : 31 ~ 81kHz
Vertical : 55 ~ 75Hz
Digital
Horizontal : 31 ~ 68kHz
Vertical : 55 ~ 75Hz
4. POWER SUPPLY
4-1. Power Adaptor
Input : AC 90~240V, 50/60 ±3Hz , 1.0A
4-2. Power Consumption
5. ENVIRONMENT
5-1. Operating Temperature: 10°C~35°C (50°F~95°F)
(Ambient)
5-2. Relative Humidity : 10%~80%
(Non-condensing)
5-3. MTBF : 50,000 Hours(Min)
6. DIMENSIONS
Without Tilt/Swivel
Width : 396.0 mm (15.59'')
Depth : 71.1 mm ( 2.79'')
Height : 330.5 mm (13.01'')
With Tilt/Swivel
Width : 396.0 mm (15.59'')
Depth : 259.0 mm (10.19'')
Height : 349.7 mm (13.7'')
7. WEIGHT
Without Stand : 5.3kg (11.69 lbs)
With Stand : 7.7kg (16.98 lbs)
CONTENTS
SPECIFICATIONS
- 2 -
SPECIFICATIONS ................................................... 2
PRECAUTIONS ....................................................... 3
TIMING CHART ....................................................... 4
OPERATING INSTRUCTIONS ................................ 5
WIRING DIAGRAM ................................................. 6
BLOCK DIAGRAM ................................................... 7
DESCRIPTION OF BLOCK DIAGRAM.....................8
ADJUSTMENT ...................................................... 10
TROUBLESHOOTING GUIDE .............................. 12
EXPLODED VIEW...................................................16
EXPLODED VIEW PARTS LIST..............................17
REPLACEMENT PARTS LIST ...............................18
PIN CONFIGURATION............................................21
SCHEMATIC DIAGRAM......................................... 23
MODE
POWER ON (MAX)
ACITIVE OFF
POWER OFF
H/V SYNC
ON/ON
OFF/OFF
-
POWER CONSUMPTION
less than 55 W
less than 3 W
less than 3 W
LED COLOR
GREEN
AMBER
OFF
VIDEO
ACTIVE
OFF
-
H
D
W
H
W
D
- 3 -
WARNING FOR THE SAFETY-RELATED COMPONENT.
• There are some special components used in LCD
monitor that are important for safety. These parts are
marked on the schematic diagram and the
replacement parts list. It is essential that these critical
parts should be replaced with the manufacturer’s
specified parts to prevent electric shock, fire or other
hazard.
• Do not modify original design without obtaining written
permission from IBM or you will void the original parts
and labor guarantee.
TAKE CARE DURING HANDLING THE LCD MODULE
WITH BACKLIGHT UNIT.
• Must mount the module using mounting holes arranged
in four corners.
• Do not press on the panel, edge of the frame strongly
or electric shock as this will result in damage to the
screen.
• Do not scratch or press on the panel with any sharp
objects, such as pencil or pen as this may result in
damage to the panel.
• Protect the module from the ESD as it may damage the
electronic circuit (C-MOS).
• Make certain that treatment person’s body are
grounded through wrist band.
• Do not leave the module in high temperature and in
areas of high humidity for a long time.
• The module not be exposed to the direct sunlight.
• Avoid contact with water as it may a short circuit within
the module.
• If the surface of panel become dirty, please wipe it off
with a softmaterial. (Cleaning with a dirty or rough cloth
may damage the panel.)
WARNING
BE CAREFUL ELECTRIC SHOCK !
• If you want to replace with the new backlight (CCFL) or
inverter circuit, must disconnect the AC adapter
because high voltage appears at inverter circuit about
650Vrms.
• Handle with care wires or connectors of the inverter
circuit. If the wires are pressed cause short and may
burn or take fire.
PRECAUTION
CAUTION
Please use only a plastic screwdriver to protect yourself
from shock hazard during service operation.
TIMING CHART
- 4 -
VIDEO
SYNC
B
D
CFE
A
<< Dot Clock (MHz), Horizontal Frequency (kHz), Vertical Frequency (Hz), Horizontal etc... (µs), Vertical etc... (ms) >>
H + 31.469 800 640 16 96 48
V–70.09 449 350 37 2 60
H + 37.879 1056 800 40 128 88
V + 60.317 628 600 1 4 23
H–31.469 800 640 16 96 48
V–59.94 525 480 10 2 33
H–37.5 840 640 16 64 120
V–75 500 480 1 3 16
H–31.468 900 720 18 108 54
V + 70.08 449 400 12 2 35
H + 46.875 1056 800 16 80 160
V + 75.0 625 600 1 3 21
H+/–49.725 1152 832 32 64 224
V+/–74.55 667 624 1 3 39
H–48.363 1344 1024 24 136 160
V–60.0 806 768 3 6 29
H–60.123 1312 1024 16 96 176
V–75.029 800 768 1 3 28
H+/–68.681 1456 1152 64 128 144
V+/–75.062 915 870 1 3 39
H+/–61.805 1504 1152 18 134 200
V+/–65.96 937 900 2 4 31
H + 63.981 1688 1280 48 112 248
V + 60.02 1066 1024 1 3 38
H + 79.976 1688 1280 16 144 248
V + 75.035 1066 1024 1 3 38
Mode H/V
Sort
1
2
3
4
5
6
7
8
9
10
11
12
13
25.175
28.321
25.175
31.5
40.0
49.5
57.283
65.0
78.75
100.0
92.978
108.0
135.0
640x350
70Hz
800x600
60Hz
640x480
60Hz
640x480
75Hz
720x400
70Hz
800x600
75Hz
832x624
75Hz
1024x768
60Hz
1024x768
75Hz
1152x870
75Hz
1152x900
65Hz
1280x1024
60Hz
1280x1024
75Hz
Sync
Polarity Frequency
Dot
Clock Total Period
(E)
Video Active Time
(A)
Sync Duration
(D)
Back Porch
(F)
Front Porch
(C)
Resolution
OPERATING INSTRUCTIONS
- 5 -
FRONT VIEW REAR VIEW
Front Control Panel
Front Control Panel
Power
Connect
AUDIO
DC OUT
USER CONTROL FEATURES
Icon Direct Access Functions
Switches the monitors on and off. Bring up Brightness adjustment.
Executes automatic image setup.
Switch between input signals.
Icon Monitor controls
and
Display main OSD menu and selects
highlighted menu item.
Moved the cursor to highlight icons or
make adjustments.
Exits from current OSD menu.
CONTROLS LOCK / UNLOCK
This feature allows you to secure the
current control settings, while allowing the
user to adjust Brightness, so that they
cannot be inadvertently changed. Push
and hold the enter button[ ] for 10
seconds; the message “Menu is Locked”
appears.
You can unlock the OSD controls at any
time by pushing the enter button[ ] for 10
seconds; the message “Menu is Unlocked”
will appear.
J705
J702
- 6 -
WIRING DIAGRAM
Connector Ass’y P/N:
6631T20022E
Connector Ass’y P/N:
6631T11016D
- 7 -
D-SUB
MST9151B
including
(ADC/LVDS/SCALER
/INPUT SWITCHING
/TMDS )
MTV412
Micom
LCD Module
R,G,B
differential
LVDS
(Low Voltage
Differential
Signaling)
12
12V V
DVI-I
R,G,B, H/V Sync Digital Signal or
Analog R,G,B,H/V
3.3V
Reg. 2.5V
Reg.
5V 5V
Power
5V
AC Input
Inverter Output
Inverter
12V
3.3V 2.5V
3.3V
2.5V
BLOCK DIAGRAM
- 8 -
DESCRIPTION OF BLOCK DIAGRAM
1. Video Controller Part & Display Data Transmitter Part.(MST9151B)
This part amplifies the level of video signal for the digital conversion and
converts from the analog video signal to the digital video signal using a pixel clock.
The pixel clock for each mode is generated by the PLL.
The range of the pixel clock is from 25MHz to 135MHz.
This part consists of the Scaler.
The Scaler gets the video signal converted analog to digital,
interpolates input to 1280 x 1024 resolution signal and outputs 8-bit R, G, B signal to transmitter.
Especially pre-amp / ADC / Video controller/ Transmitter are merged to one chip"MST9151B" by MSTAR.
This part transmit digital signal from the Scaler to the receiver of module.
2. Micom Part
This Part consists of EEPROM IC which stores control data, Reset IC and the Micom.
The Micom distinguishes polarity and frequency of the H/V Sync are supplied from signal cable.
The controlled data of each modes is stored in EEPROM.
3. Power Part
This part consists of the one 3.3V and one 2.5 regulators to convert power which is provided 5V in LIPS Board.
Also, 5V is converted 3.3V and 2.5V by regulator. Converted power is provided for Scaler IC in the main board.
12V is provided for LCD Panel.
4. Inverter
The inverter converts from DC12V to AC 700Vrms and operates back-light lamps of module.
- 9 -
EMI
COMPONENTS
LINE
100 ~ 240V
INPUT RECTIFIER
AND FILTER ENERGY
TRANSFER OUTPUT RECTIFIER
AND FILTER
12V
5V
GND
SIGNAL
COLLECT-
ION
PHOTO
INVERTER CIRCUIT High Voltage output
12V
-COUPLER
ISOLATION
PWM CONTROL
CIRCUIT
HVDC 100KHz
PRIMARY SECONDARY
50 ~ 60Hz
Operation description_Power
1. EMI components.
This part contains of EMI components to comply with global marketing EMI standards like FCC, VCCI CISPR, the
circuit included a line-filter, across line capacitor and of course the primary protection fuse.
2. Input rectifier and filter.
This part function is for transfer the input AC voltage to a DC voltage through a bridge rectifier and a bulk capacitor.
3. Energy Transfer.
This part function is transfer the primary energy to secondary through a power transformer.
4. Output rectifier and filter.
This part function is to make a pulse width modulation control and to provide the driver signal to power switch, to
adjust the duty cycle during different AC input and output loading condition to achive the dc output stablize, and also
the over power protection is also monitor by this part.
5. Photo-Coupler isolation.
This part function is to feed back the dc output changing status through a photo transistor to primary controller to
achieve the stabilized dc output voltage.
6. Signal collection.
This part function is to collect the any change from the dc output and feed back to the primary through photo
transistor
- 10 -
ADJUSTMENT
Windows EDID V1.0 User Manual
Operating System: MS Windows 98, 2000, XP
Port Setup: Windows 98 => Don’t need setup
Windows 2000, XP => Need to Port Setup.
This program is available to LCD Monitor only.
1. Port Setup
a) Copy “UserPort.sys”file to
“c:\WINNT\system32\drivers”folder
b) Run Userport.exe
c) Remove all default number
d) Add 300-3FF
e) Click Start button.
f) Click Exit button.
2. EDID Read & Write
1) Run WinEDID.exe
2) Edit Week of Manufacture, Year of Manufacture,
Serial Number
a) Input User Info Data
b) Click “Update”button
c) Click “Write”button
Other manuals for ThinkVision L180p
1
This manual suits for next models
2
Table of contents
Other IBM Monitor manuals
IBM
IBM 6656HG2 - T 560 - 15" LCD Monitor User manual
IBM
IBM T750 User manual
IBM
IBM 24P4555 - E 54 - 15" CRT Display User manual
IBM
IBM P76 User manual
IBM
IBM 9503-T221 General instructions
IBM
IBM T220 User manual
IBM
IBM E74 User manual
IBM
IBM T541A User manual
IBM
IBM T-120 User manual
IBM
IBM THINKPAD E50 User manual
IBM
IBM 6517-6LN E74M User manual
IBM
IBM C220p User manual
IBM
IBM THINKPAD E50 User manual
IBM
IBM MM75 User manual
IBM
IBM 6552-23N User manual
IBM
IBM T74 User manual
IBM
IBM T84H User manual
IBM
IBM 494215U - T 115 - 15" LCD Monitor User manual
IBM
IBM 9503DG1 - T 221 - 22.2" LCD Monitor User manual
IBM
IBM T54H User manual
