IBM 6736-HB0 User manual
L200p
User’s Guide
Color Monitor
English
iii
First Edition (February / 2003)
Note : For important information, refer to the Monitor Safety and Warranty manual that comes with this monitor.
ENGLISH
1
Safety (Read first).......................................................................................................2
Setting up the monitor...............................................................................................3
Product Description..............................................................................................3
Handling Instructions ...........................................................................................3
Workplace preparation.........................................................................................4
Adjusting the Monitor Position .............................................................................5
Working Practices................................................................................................6
Caring for your Monitor........................................................................................6
Connecting your Monitor......................................................................................7
Switching on your Monitor....................................................................................8
Device Driver Installation...........................................................................................9
Windows 95/98 ....................................................................................................9
Windows 2000/Me..........................................................................................................10
Windows XP....................................................................................................................11
Automatic Image Setup............................................................................................12
Image Setup.......................................................................................................12
Image Setup for DOS.........................................................................................13
Image Setup for Windows 95, Windows 98, Windows 2000, Windows NT,
Windows Me or Windows XP
...................................................................................
14
Manual Image Setup.................................................................................................15
Adjusting Your LCD Monitor ...................................................................................16
User controls......................................................................................................16
On-screen display (OSD) controls.....................................................................17
Further Information..................................................................................................20
Display modes ...................................................................................................20
Power Management...........................................................................................21
Product Disposal................................................................................................21
Troubleshooting .......................................................................................................22
Help and Service Information.............................................................................24
Specifications...........................................................................................................25
Service Information..................................................................................................26
Notices and Trademarks..........................................................................................27
Contents
2
í í í
T710_E_update.fm Page 2 Monday, July 8, 2002 11:44 AM
ENGLISH
3
Setting up the monitor
Handling InstructionsHandling Instructions
1. Lift the monitor by placing your hands where indicated below.
2. Before using your monitor for the first time, remove the clear protective
film from the front of the screen.
Product Description
This monitor requires a computer with a suitable on-board sub-system or
Video Adapter card that can support UXGA 1600 x 1200, SXGA 1280 x
1024, XGA 1024 x 768, SVGA 800 x 600, or VGA 640 x 480 at 60Hz.
In addition to your monitor, your option package includes the following:
•User's Guide and Installation Files CD
•Monitor Safety and Warranty Information Manual
•L200p Color Monitor Quick Setup Guide
•Power Cord
•L200p Color Monitor
•Analog Interface Cable - Attached to Monitor
Do not support the monitor within
the screen area. The Liquid
Crystal Display is glass and can
be damaged by rough handling or
excessive pressure.
4
i
This section gives advice
on what you should
consider before you set up
your monitor.
Workplace Preparation
Height
Position the monitor so that the top of the screen is slightly below your eye
level when you sit at your workstation.
Orientation
- Choose a position that gives the least reflection from lights and windows,
usually at a right angle to any windows.
- Positon the monitor directly in front of you so that you do not have to twist
your body to use it.
- Tilt the monitor to a comfortable viewing angle.
3. Before adjusting your monitor for the first time, remove the locking clip
on rear of the stand. Carefully hold the screen of the monitor and then
squeeze at arrows shown to remove(Figure A).
(Figure A)
ENGLISH
55
i
With the IBM Flat Panel
Monitor, you can adjust its
position in various ways for
maximum comfort.
Viewing Angle
You can tilt the screen forward and backward as shown below in Figure A.
Swivel
You can swivel the screen to the left or the right as shown below in Figure A.
Height
You can adjust height of the screen as shown below in Figure B.
(Figure A) (Figure B)
Adjusting the Monitor Position
6
Be sure to turn off the power before you perform any maintenance on the
monitor. Clean your monitor as follows:
• Gently wipe the covers and the screen with a soft cloth.
Do not use solvents or abrasives.
• Remove finger marks and grease with a damp cloth and mild detergent.
• Never use flammable cleaning materials to clean your IBM monitor or
any other electrical apparatus.
Caring for your Monitor
i
This section gives advice
on how you can work
comfortably and reduce
fatigue.
Rest
Take regular breaks. Vary your posture, stand up and stretch occasionally
as prolonged use of computer workstations can be tiring.
Back
Sit back in your chair and use the backrest.
Hands
Adjust the seat height so that your forearms are approximately horizontal
and your wrists are straight when using the keyboard. Your upper arms
should be relaxed with your elbows near your body.
Use a light touch on the keyboard, keeping your hands and fingers relaxed.
Allow a space in front of the keyboard to rest your wrists when not typing.
Consider using a wristpad.
Eyesight
Working with monitors, in common with any prolonged close work, can be
visually demanding. Look away from the screen periodically and have your
eyesight checked regularly.
Screen settings
Set the screen brightness and contrast to a comfortable level. You may
have to adjust these settings as the lighting changes during the day. Many
application programs let you select color combinations which can help you
to view in comfort. See the User controls section on page 16 for more
information.
Working Practices
A
ENGLISH
7
Connecting your Monitor
1. Turn off your computer and all attached devices. Next, unplug the
power cord(s) to your computer and all attached devices.
2. Connect the signal cable.
The analog signal cable is already connected to your monitor. The
analog connector is the blue connector.
When connecting the analog signal cable (Figure A)
Connect the free end of the attached signal cable to the 15-pin Monitor
port on the computer and tighten screws.
If connecting a DVI-D digital signal cable (Figure B)
Connect one end of the monitor signal cable to the white connector
on the rear panel of the monitor. Connect the other end to the white
connector on the rear panel of the computer and tighten the screws.
(Figure B)
(Figure A)
Cable not supplied
(Optional)
Be sure to read the ‘Safety’
Information located in the
Monitor Safety and Warranty
Information Manual before
carrying out this procedure.
8
1. Switch on your computer.
2. Switch on the monitor power source by pushing the power switch on side
rear panel of the monitor.(See Figure B)
3. Switch on your monitor by pushing and releasing the power switch marked [ ]
at the front of the bezel.
[To switch off your monitor, push and release the power switch again.]
4. To update or install device drivers, follow the instructions in the Device Driver
Installation section on page 9.
5. If you are using the analog connector, run Image Setup by following the
instructions in the Automatic Image Setup section on page 12.
Switching on your Monitor
3. Connect the power cord to the monitor and then plug the power cord into a
properly grounded outlet. Next, reconnect the power cord(s) to your computer
and all attached devices.
A
This manual suits for next models
1
Table of contents
Other IBM Monitor manuals
