Hyundai HMTB52-1 User manual
Gasoline Tiller
ORIGINAL INSTRUCTIONS
1
CAUTION: Read the instructions carefully. Be familiar with the controls and
the proper use of the equipment
WARNING:
For your safety and safety of others please pay special attention to
these precautions:
Read the instruction manual before use
Risk of projections! Keep bystanders at least 15 m away!
Caution: rotating working tool!
Danger: disconnect spark plug wire before servicing unit!
2
Check oil and fuel before start to use
That the machine shall always be used in accordance with these
manufacturer's instructions the instruction handbook
The engine shall be stopped when carrying out maintenance and
cleaning operations, when changing tools and when being transported
by means other than under its own power;
Some hazards can be met when working on slopes; work slowly by
holding firmly the tool. Do not transport the tool on slopes. The hazards
can rise when working on difficult soil (stony, hard, etc.). there is a risk
to hit some objects, sliding, lose control for the machine which will gives
damages. Always inspect the working area before working, and always
watch what you are doing.
The adjustable part of the protective device shall be adjusted to the
working depth of the tool so that only that part of the working tool that
cuts into the soil remains uncovered. This does not apply to motor hoes.
1) Training
a) Read the instructions carefully. Be familiar with the controls and the
proper use of the equipment;
b) Never allow children or people unfamiliar with these instructions to use
the machine. Local regulations can restrict the age of the operator;
c) Never work while people, especially children, or pets are nearby;
d) Keep in mind that the operator or user is responsible for accidents or
hazards occurring to other people or their property.
2) Preparation
a) While working, always wear substantial footwear and long trousers. Do
not operate the equipment when barefoot or wearing open sandals;
3
b) Thoroughly inspect the area where the equipment is to be used and
remove all objects which can be thrown up by the machine;
c) WARNING – Petrol is highly flammable:
Store fuel in containers specifically designed for this purpose;
Refuel outdoors only and do not smoke while refuelling;
Add fuel before starting the engine. Never remove the cap of the
fuel tank or add petrol while the engine is running or when the
engine is hot;
If petrol is spilled, do not attempt to start the engine but move the
machine away from the area of spillage and avoid creating any
source of ignition until petrol vapours have dissipated;
Replace all fuel tank and container caps securely;
d) Replace faulty silencers;
e) Before using, always visually inspect to see that the tools are not worn
out or damaged. Replace worn out or damaged elements and bolts in sets
to preserve balance.
3) Operation
a) Do not operate the engine in a confined space where dangerous carbon
monoxide fumes can collect;
b) Work only in daylight or in good artificial light;
c) Always be sure of your footing on slopes;
d) Walk, never run with the machine;
e) For wheeled rotary machines, work across the slopes, never up and
down;
f) Exercise extreme caution when changing direction on slopes;
g) Do not work on excessively steep slopes;
h) Use extreme caution when reversing or pulling the machine towards you;
i) Do not change the engine governor settings or overspeed the engine;
j) Start the engine carefully according to manufacturer instructions and with
feet well away from the tool(s);
k) Do not put your hands or feet near or under rotating parts;
4
l) Never pick up or carry a machine while the engine is running;
m) Stop the engine:
Whenever you leave the machine;
Before refuelling;
n) Reduce the throttle setting during engine shut down and, if the engine is
provided with a shut-off valve, turn the fuel off at the conclusion of working;
4) Maintenance and storage
a) Keep all nuts, bolts and screws tight to ensure the equipment is in safe
working condition;
b) Never store the equipment with petrol in the tank inside a building where
fumes can reach an open flame or spark;
c) Allow the engine to cool before storing in any enclosure;
d) To reduce the fire hazard, keep the engine, silencer, battery compartment
and petrol storage area free of vegetative material and excessive grease;
e) Replace worn or damaged parts for safety;
f) If the fuel tank has to be drained, this shall be done outdoors.
Thrown Object Hazard
Objects hit by the rotating tines can be thrown from the tiller with great force
and may cause severe injury.
1. Before tilling, clear the tilling area of sticks, large stones, wire, glass etc.
2. Pieces thrown from worn or damaged-tines can cause serious injury.
Always inspect the tines before using the tiller.
Fire and Burn Hazard
Gasoline is extremely flammable and gasoline vapor can explode.
Use extreme care when handing gasoline. Keep gasoline out of reach of
children.
1. Refuel in a well-ventilated area with the engine stopped.
2. Allow the engine to cool before refueling. Fuel vapor or spilled fuel may
be ignited.
5
3. The engine and exhaust system becomes very hot during operation and
remains hot after stopping. Touching them can cause burn injuries or
some materials burn.
4. Avoid touching a hot engine or exhaust system.
5. Allow the engine to cool before performing maintenance or storing the
tiller indoors.
Carbon Monoxide Poisoning Hazard
Exhaust contains poisonous carbon monoxide a colorless and odorless gas.
Breathing exhaust can cause loss of consciousness and may lead to death.
Operation on Slope
1. When tilling on slopes, keep the fuel tank with less than half oil to
minimize fuel spillage.
2. When the tiller walks across the slope, put your effort evenly while
walking up and down the slope.
3. Be very careful when changing the direction of the tiller on a slope.
4. Do not use the tiller on a slope of more than 10°.
5. The maximum safe grade angle shown is for reference only and the
details should depend on the type of the tool. Before starting the engine,
check that the tiller is not damaged and in good condition. For your
safety or safety of others, pay special attention when using the tiller up
or down hill.
6
STRUCTURAL REPRESENTATION
1.FORWARD CLUTCH 8.BLADE SET
2.REVERSE CLUTCH (HMTB52-1,HMTB5255-3:2SETS)
(HMTB52-1 WITHOUT) (HMTB6855-3:3SETS)
3.HANDLE (HMTB8365-3:4SETS)
4.GIRDER 9.FRONT WHEEL
5.BELT COVER 10.ENGINE
6.OUTER MUDGUARD 11.THROTTLE SWITCH
(HMTB52-1,HMTB5255-3 WITHOUT)
7.REAR DISC 12.EXTINGUISH SWITCH
7
ASSEMBLY
1. Open the package and take the machine out carefully!
2. Install Drag Bar
Put the drag bar to the hole of the back side of the frame .Fix the
screw M8x16 on the side .
3. Install baldes :
HMTB52-1,HMTB5255-3 : 2SETS BLADES , 6x M10 Screw ,6xM10 nut
8
HMTB6855-3: 3SETS BLADES, 8x M10 Screw ,8xM10 nut
HMTB8365-3 : 4SETS BLADES,10x M10 Screw ,10xM10 nut
Connect the blade set and rear disc one by one with M10x45 screws and
M10 nuts . Next put the whole blade set to the shaft of the gear box . Tight
it with M10x45 and M10 nuts .
(Please make sure that the edges of tines forward to the front wheel).
4. Install Front Wheel ：Put one M8x45 screw to the inner hole of the
frame , inset the front wheel , and fix it with another M8x45 screw .
9
5. Install the Handle assemble .
a. Fit Grider to the frame with 4xM8x16 screw .
b. Take the bolt and pin out of the above Grider , put the Handle above
the Grider and fix with bolt and pin .
c. Fit Throttle switch , Forward clutch , Reverse Clutch(HMTB52-1
without Reverse Clutch) to the Handle .
This manual suits for next models
3
Table of contents
Other Hyundai Tiller manuals
Popular Tiller manuals by other brands
MTD
MTD OHV Series Original operating instructions
YAT
YAT YT5601-01 Assembly, Use, Maintenance Manual
Craftsman
Craftsman 917.296010 owner's manual
Troy-Bilt
Troy-Bilt OEM-290-260 Operator's manual
Scheppach
Scheppach MTP560 Translation from the original instruction manual
GARDEN WAY
GARDEN WAY 12194 owner's manual
Classen
Classen STAND-AER SA-25 Operator's manual and parts list
Craftsman
Craftsman 850 Series owner's manual
DR
DR PILOT 2 Safety & Operating Instructions
Altrad
Altrad ATIKA BH 1400 N Original instructions, safety instructions, spare parts
WIL-RICH
WIL-RICH 2500 Operator's manual
Viking
Viking HB 685 instruction manual