Hussmann IMPACT RL User manual

PARTS LIST

Item Quantity Description

RL/RM RLN RLNI

RM/RMF RMN RLNIE RLT

1.2242Donut Gasket

2.1122Gasket, 1 x 1/2 x 180 in.

3.1121Gasket, 1/2 x 1/4 x 180 in.

4. 6 6 12 6 Cap Screw 5/16 -18 x 11/4

5. 6 6 12 6 Split Lock Washers 5/16

6.1121Joint Molding

7. 5 5 10 5 Binder Post and Screw

8.1121Splice Connector

Merchandisers

RL / RM / RMF, RLT

RLN / RMN / RLNI / RLNIE

Joining Instructions

Reach-in Merchandisers

NOTE: Be sure first merchandiser

has been leveled according to the

main installation instruction.

Carefully unpack and inspect the

joining parts listed above to verify

completeness and that there is no

damage.

1Prepare cases for joining (both

sides of islands) as shown in

Figure 1.

A. Remove bumpers, rails,

packing materials, and splash-

guards from the both cases.

B. Remove shelves (if

installed).

C. Remove display racks and

pans from ends to be joined.

D. Remove rear shelf supports.

HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A. 1

Splashguard brackets must

be installed before piping

or wiring case.

Figure 1. Prepare Cases

Bumper

Retainer

Splashguard

SIDE VIEW

Raceway

Bumper

Retainer

Splashguard

SIDE VIEW

RLT

P/N 0387177F

October 2005

E. Remove back panels from

ends to be joined by lifting up

and out near the bottom. No

tools are necessary. The RLT

models have upper and lower

back panels that must be

removed.

F. Remove joint molding from

any door frames that will be

joined to another case.

G. RLNI Only: Remove screws

and interior top panel on both

sides of the island case end to

be joined (see Figure 1).

Merchandisers

P/N 0387177F

2HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.

RLNI Only

Alignment Pin

RL / RM / RMF

RLN / RMN

and RLNI

RLT

2Locate and remove the shipping

block in the center of the heat

exchanger in the interior bottom

of each case, see Figure 2.

Snap a chalk line on the floor to

use as a guide for positioning

the front of the cases in the line-

up. The front base frame should

be on the chalk line.

3Once cases are close to final

placement, remove the shipping

braces from the ends to be

joined, see Figure 3. Discard

bolts and flat washers used to

hold shipping braces. Bolts

are too long to be used for

joining.

P/N 0387177F

Reach-in Joining Instruction

HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.

Figure 2. Remove Shipping Block

(One From Each Side of Island Models)

Shipping

Block

RMN

RLNI / RLNI

Figure 3. Remove Shipping Braces

DO NOT USE SHIPPING BOLTS TO JOIN CASES!

Shipping Brace

Merchandisers

P/N 0387177F

4HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.

Factory Installed

Nut Retainer

RL / RM / RMF

and

RLN / RMN

4If not already installed make

sure Nut Retainers and

Alignment Pins are in place in

the right end frame as shown in

Figure 4A or 4B.

Factory Installed

Nut Retainer

RLT has no

Alignment Pin

RLT

Figure 4A. Verify Nut Retainer Installation

P/N 0387177F

Reach-in Joining Instruction

HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.

Alignment Pin Alignment Pin

RLNI

Figure 4B. Verify Nut Retainer Installation

5Apply Donut Gasket – 1 in

recess around both left end as

shown in Figure 5A, Part 1; 5B

or 5C, Part 1, and right end

frames as shown in Figure 5A,

Part 2; 5B or 5C, Part 2.

Apply the wider Foam Tape

Gasket — 2 around the right

end frame as shown in Figure

5A, Part 2, 5B or 5C, Part 2.

Merchandisers

P/N 0387177F

6HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.

Figure 5A, Part 1. Apply Gasket to Left End of RL/RM/RMF and RLN/RMN

Donut

RL / RM / RMF

and

RLN / RMN

Apply the narrower Foam Tape

Gasket — 3 around the

perimeter of the right end frame

outside of the donut gasket as

shown in Figure 5A, Part 2, 5B

or 5C, Part 2.

• Lap gaskets at lower corners.

• Check that there are no gaps

between gasket and case.

• Do not stretch gasket,

especially around corners. To

make sharp corners, paper

backing can be torn without

removing from gasket.

• Do not butt gaskets; always

lap joints.

• Remove paper backing after

gasket is applied to keep gasket

free of debris.

• Gasket has high tack

adhesive and must be properly

placed the first time.

P/N 0387177F

Reach-in Joining Instruction

HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.

1 in. x 1/2in.

Donut

1/2in. x 1/4in.

Make sure area where raceway attaches to end frame

is sealed with the wider 1 in. x 1/2in. gasket.

Figure 5A, Part 2. Apply Gaskets to Right End of RL/RM/RMF and RLN/RMN

RL / RM / RMF

and

RLN / RMN

ALL MODELS:

Apply gasket

between wipes.

NOTES:

1. The perimeter gasket, ITEM 3,

is required by NSF.

2. Butyl is NOT an acceptable

substitute for donut or foam

gasket.

Merchandisers

P/N 0387177F

8HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.

Figure 5A. Apply Gaskets to Left End of RLNI

Gaskets

Must Be

Applied As

Shown

Donut

RLNI

P/N 0387177F

Reach-in Joining Instruction

HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.

Gaskets

Must Be

Applied As

Shown

Make sure area where raceway attaches to end

frame is covered with wider 1 in. x 1/2in. gasket.

1 in. x 1/2in.

Donut

1/2in. x 1/4in.

Figure 5B. Apply Gaskets to Right End of RLNI

RLNI

Merchandisers

P/N 0387177F

10 HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.

Figure 5C, Part 1. Apply Gasket to Left End of RLT

Donut

Other manuals for IMPACT RL

This manual suits for next models

Table of contents

Other Hussmann Merchandiser manuals

Hussmann

Hussmann MD Series User manual

Hussmann

Hussmann Q3 User manual

Hussmann

Hussmann GGSM Quick guide

Hussmann

Hussmann impact Excel C2X-LGE Instruction Manual

Hussmann

Hussmann Impact C2-XLE Instruction Manual

Hussmann

Hussmann SI1N Instruction Manual

Hussmann

Hussmann Impact Excel C6X-LEP Instruction Manual

Hussmann

Hussmann IMPACT CW2U-XGE Instruction Manual

Hussmann

Hussmann FML User manual

Hussmann

Hussmann Impact Excel P2X-E Instruction Manual

Hussmann

Hussmann IMPACT Elite E1 User manual

Hussmann

Hussmann Impact Excel C6X-E Instruction Manual

Hussmann

Hussmann Impact C2-LGE Instruction Manual

Hussmann

Hussmann DSIO3-Y Operating instructions

Hussmann

Hussmann SCSS Instruction Manual

Hussmann

Hussmann SMGT User manual

Hussmann

Hussmann FMRA User manual

Hussmann

Hussmann DM User manual

Hussmann

Hussmann RGD Instruction Manual

Hussmann

Hussmann LIG User manual

Hussmann

Hussmann ESGS User manual

Hussmann

Hussmann Specialty Products CR3P Instruction Manual

Hussmann

Hussmann Impact Excel M5X-GEP Instruction Manual

Hussmann

Hussmann LGH Instruction Manual

Popular Merchandiser manuals by other brands

FRIGOGLASS

FRIGOGLASS Flex 20 HC user manual

EPTA

EPTA COSTAN RHINO MULTI User instructions

CASCO

CASCO Nano Cube owner's manual

True

True GDIM-26 installation manual

Structural Concepts

Structural Concepts Oasis Mobile Series Installation & operating manual

Haussmann

Haussmann RL Installation & operation manual

Howard McCray

Howard McCray R-CDS32E-4 Specifications

EPTA

EPTA iarp Cool Emotions Delight Lite User instructions

VALERA

VALERA BC 85 datasheet

HL Display

HL Display 3eBin Assembly instructions

Dixie Narco

Dixie Narco DNCB 501E Technical manual

APW Wyott

APW Wyott Racer DMXD-30H Installation and operating instructions

Hoshizaki

Hoshizaki KD-90C Service manual

Summit

Summit SCR1006 instruction manual

Delfield

Delfield Shelleyspeed SPM-28E Specifications

EPTA

EPTA iarp Cool Emotions GLEE 40 User instructions

Kysor/Warren

Kysor/Warren GranBering KW TECHNICAL MANUAL & USER INSTRUCTIONS

Crane

Crane BevMAX Refresh 6 Media Operation guide