Husqvarna TS73R Manual
Standard Operating Procedure
HUSQVARNA TILE SAW 9” TS73R
Version 3 Issue date: 6/05/2017
Page 1 of 4
20 Goodshed Road Upper Hutt
Phone 04 528 4473
Section 1: Equipment Identification and Supplier details
Name
Husqvarna Tile Saw 9” TS73R
Recommended Use
Water-lubricated cutting of marble, stone, granite, brink and
facings, including porcelain, glazed tiles ceramics etc.
Manufacturer / Importer
Husqvarna Construction Products
NZ Importer Youngman Richardson
www.yrco.co.nz
Emergency Contact details
Garry Bull (Upper Hutt Hire) 027 742 6583
Links to safety information
None at this time
Does this equipment require a daily check or inspection and entry in a log book?
No
Section 2: Emergency Stop
In an emergency Turn the switch off.
Alternatively unplug the power saw.
If the electrical cable or components are damaged, you are
authorised by Upper Hutt Hire to cut the plug off the power
cable, to prevent inadvertent use.
Section 3: Hazards Identification
DANGER: High Voltage! Risk of Electrocution!
Always use a residual-current circuit breaker (RCCB), Ground
Fault Circuit Interrupter, Transformer or other suitable
electrical Safety device.
When operating outdoors, use an extension cord suitable for
outdoor use.
DANGER: RISK OF AMPUTATION!
NEVER place hands and feet in the feed anywhere near the
blade. RISK of limbs being severed. If a blockage occurs turn off
the engine, unplug it, and allow machine to come to a
COMPLETE STOP before clearing obstructions.
DANGER: RISK OF FLYING DEBRIS.
Always wear eye protection
ELECTRIC MOTOR = POTENTIAL IGNITION SOURCE
Do not operate in areas where there is fuel vapour, LPG, or
high levels of flammable dust.
Do not operate in explosive atmospheres such as in the
presence of flammable liquids, gases or dust.
Standard Operating Procedure
HUSQVARNA TILE SAW 9” TS73R
Version 3 Issue date: 6/05/2017
Page 2 of 4
20 Goodshed Road Upper Hutt
Phone 04 528 4473
DANGER: RISK OF INHALATION OF PARTICULATE DUST.
Dry material may generate dust. Always use the water
lubrication system.
Wear breathing protection as necessary.
Do not allow persons to operate machinery without full and
proper instruction in the use of the machine. Do not allow
person under 18 year’s age to operate the machinery.
Never leave the engine running when unattended. Shut the
machine down even if unattended for a short period.
Risk of Burns. Parts may become very hot. Do not touch!
Operation of the equipment must not be performed by persons
under the influence of alcohol, drugs, medications or any
chemical substances capable of impairing the abilities of that
person.
Continuous operation may result in exhaustion or stress to the
operator. Take frequent breaks and do not operate if you are
feeling tired.
SINGLE OPERATOR ONLY! This machine is designed for control
and operation by one attendant (operator) only, who must
always stand directly behind the machine when in use.
Never operate if the safety guards have been removed.
Section 4: Noise and Vibration
Measured Sound level: 66 dB
Guaranteed Sound Power Level: 105 dB
OPERATOTS MUST USE HEARING PROTECTION
Ear Muffs or plugs must be compliant with AS/NZS 1270:2002
Acoustics –Hearing Protectors Class 4 or 5.
Vibrations aw (m.s-2)
Thought to be less than 1 ms2. Not thought to be significant.
Section 5: Work Zone
5.1 Work Zone Control or Isolation
Does the work zone
require control or
isolation?
Yes: Isolate work area from the general public
Standard Operating Procedure
HUSQVARNA TILE SAW 9” TS73R
Version 3 Issue date: 6/05/2017
Page 3 of 4
20 Goodshed Road Upper Hutt
Phone 04 528 4473
5.2 Precautions for site
Do you have a
FIRST AID KIT?
Do you have a
FIRE EXTINGUISHER?
Can you make an
EMERGENCY CALL?
Section 6: Personal Protective Equipment (PPE)
Appropriate Personal Protective Equipment (PPE) is required for the operator and persons
assisting with loading and unloading.
Wear High Visability clothing if you are working with other people on the work site.
Tight fitting gloves recommended.
Section 7: Power Source and Lubricants
Power source
240V Electricity. Always use a residual-current circuit breaker (RCCB),
Ground Fault Circuit Interrupter, Transformer or other suitable electrical
Safety device.
Section 8: Operating instructions
1. To start the machine press the green button on the switch.
2. To stop the machine, press the red button.
Square Cuts:
Place the dish support head to the rear of the slide.
Position the tile on the table with the edge firmly against the plate stop
Pull the head steadily towards you without forcing the blade or making sudden contact
with the tile.
45° Degree bevel cuts:
Loosen the two adjusting nuts on the
support head
Tip over the cutting head and rail assembly
Retighten the adjusting nuts and follow the
instructions as above.
Standard Operating Procedure
HUSQVARNA TILE SAW 9” TS73R
Version 3 Issue date: 6/05/2017
Page 4 of 4
20 Goodshed Road Upper Hutt
Phone 04 528 4473
Section 9: Transport
1. Unplug the machine
2. Lock the head on the rear part of the saw, using clip ‘A”, so that the head is secured.
3. Loosen the two flywheels (B) of the front legs, and swivel them to a horizontal position,
then retighten the flywheels.
4. Repeat the same procedure for the back legs.
5. To reinstall the machine on its legs, carry out the above procedure in reverse.
Section 10: Additional Information
Always use common sense! It is not possible to cover every conceivable situation you can face when using our equipment. Always
exercise care and use your common sense. Avoid all situations which you consider to be beyond your capability. If you still feel
uncertain about operating procedures after reading these instructions and the owner’s manual, you should consult an expert before
continuing. The information contained herein is true and accurate to the best of our knowledge. No warranty or guarantee is
expressed or implied regarding the accuracy of information or instructions. Users MUST consult the manufacturer’s manual or
handbook. While every effort has been made to summarise the important Health and Safety information for the safe use of this
equipment, Upper Hutt Hire Ltd shall not be liable in any way for any reliance by any person or entity on the accuracy of information
or data contained in this document or its attachments.
Revision date
May 2022 (SOP based on Husqvarna Manual TS73R 115 03 00-20 2007-03-15)
Other Husqvarna Saw manuals
Husqvarna
Husqvarna CS 10 User manual
Husqvarna
Husqvarna Prelude 350 User manual
Husqvarna
Husqvarna MS 355 User manual
Husqvarna
Husqvarna WS 462 User manual
Husqvarna
Husqvarna MS 355 User manual
Husqvarna
Husqvarna PA 1100 User manual
Husqvarna
Husqvarna TS 400 F User manual
Husqvarna
Husqvarna MS 360 G User manual
Husqvarna
Husqvarna MADSAW 525iDEPS User manual
Husqvarna
Husqvarna FS5000 D User manual
Husqvarna
Husqvarna TS 355 B User manual
Husqvarna
Husqvarna FS 520 User manual
Husqvarna
Husqvarna FS 305 User manual
Husqvarna
Husqvarna K 970 III User manual
Husqvarna
Husqvarna FS400LV User manual
Husqvarna
Husqvarna FS400LV User manual
Husqvarna
Husqvarna K 3000 Vac User manual
Husqvarna
Husqvarna TS 250 X3 User manual
Husqvarna
Husqvarna RC 455 User manual
Husqvarna
Husqvarna K 540i User manual
