Hunter Pacific Concept User manual

Electrician Installation Manual

Concept Ceiling Fan

(Timber and Moulded Blades)

1. Do not attempt to operate the fan (or optional light kit) with any wall control that is not

approved by Hunter Pacific for use with its fans. DO NOT use solid state controllers. The

use of unapproved controllers will void your warranty.

2. Do not mix blade sets from one fan to another as this may upset the balance of the fan. If

CEILING FAN MUST BE INSTALLED

BY A LICENSED ELECTRICIAN

(NO OTHER PERSONS SHOULD ATTEMPT TO INSTALL THIS FAN)

*Electricians are recommended to tick off all items on the quick

checklist and fill out their details onto the back page of the Fan

Owner Warranty & Operations Manual after installation

National Warranty Line

1300 360 280

ELECTRICIANS - TO PROTECT YOUR CUSTOMER’S WARRANTY, PLEASE READ

PAGE 2 OF THIS BOOKLET PRIOR TO THE INSTALLATION OF THIS PRODUCT.

Electrician Installation Manual

Concept Ceiling Fan

(Timber and Moulded Blades)

1. Do not attempt to operate the fan (or optional light kit) with any wall control that is not

approved by Hunter Pacific for use with its fans. DO NOT use solid state controllers. The

use of unapproved controllers will void your warranty.

2. Do not mix blade sets from one fan to another as this may upset the balance of the fan. If

only one blade is damaged you are still required to replace with a new set.

IMPORTANT INFORMATION

ELECTRICIANS MUST READ PRIOR TO INSTALLATION

1. Distributor and installer details and purchase receipts are essential for on-site warranty claims

and must be presented to repair personnel, make sure you record your details in the Fan Owner

Warranty and Operations Manual.

2. Fans and fixed wiring products must only be installed by persons who are appropriately licensed

by the applicable State regulatory body. Therefore, to protect our repair personnel, on-site

warranty claims will not be accepted if products have been installed by unlicensed persons.

3. Damage caused by incorrect installation, force-majeure, electrical surges, lightning, power grid

fluctuations, water or by connection to alternative power supply sources (such as solar inverters,

etc.) is not eligible for warranty repair.

4. Blades must be replaced only as a complete set. Blades are supplied only as a pre-balanced set

and the replacement of individual blades may void the warranty by causing mechanical

damage to the motor, excessive noise or premature wear.

5. When products are installed in a location requiring special access equipment (such as

scaffolding or scissor lifts, etc) the cost of providing, installing and operating special access

equipment must be borne by the site owner.

For safety, and to protect your customers warranty, the following must be taken into

account when installing and operating the product(s):

IF THERE ARE ANY PROBLEMS WITH THE PRODUCT AT TIME OF

INSTALLATION THE INSTALLER MUST CONTACT THE WARRANTY

HOT LINE NUMBER 1300 360 280. BEFORE LEAVING THE JOB

SITE. PLEASE DO NOT REMOVE THE FAN FROM THE CEILING

ONCE INSTALLED UNLESS INSTRUCTED TO DO SO.

(a) DO NOT USE SOLID-STATE WALL CONTROLLERS. Neither leading nor lagging edge

controllers will give satisfactory performance. Wall controls must only be types approved

for use by Hunter Pacific International.

(b) The fan, light and bracket must be earthed.

(d) Mounting bracket must be firmly screwed to a solid structure such as a concrete ceiling,

steel structure or timber framing. If additional bracing is added it must be firmly secured to

the rafters and not left floating on the ceiling. Special mounts, such as T-hooks, are

available for certain types of installation.

(e) After installation, fan blades must be at least 2.1 m (7 feet) above floor level.

(f) The use of these products by children and the infirm must be under supervision.

Electrician Installation Manual

Concept Ceiling Fan

(Timber and Moulded Blades)

1. Do not attempt to operate the fan (or optional light kit) with any wall control that is not

approved by Hunter Pacific for use with its fans. DO NOT use solid state controllers. The

use of unapproved controllers will void your warranty.

2. Do not mix blade sets from one fan to another as this may upset the balance of the fan. If

only one blade is damaged you are still required to replace with a new set.

Hanger Bracket

Hex Head Screw

Ball Joint

Canopy Cover

Parts List

Concept 2 Ceiling Fan Parts List

Part Qty Part Qty Part Qty

Blades 4 Base Plate 1 Canopy Cover Screws 2

Blade Screws 12 HPI Wall Controller 1 Canopy Cover 1

Blade Washers 12 Hanger Bracket 1 Motor Housing 1

Wall Speed Capacitor 1 Hex Head Screw 2

Ball Joint 1 15cm Down Rod 1 Reversing Switch Cover 1

Ball Joint Screw 1 Down Rod Pin Screw 1

Ball Joint Pin 1 Down Rod Short Screw 1

(these parts come preassembled)

Blade

Blade Screw

Base Plate

Motor

Housing

Electrician Installation Manual

Concept Ceiling Fan

(Timber and Moulded Blades)

1. Do not attempt to operate the fan (or optional light kit) with any wall control that is not

approved by Hunter Pacific for use with its fans. DO NOT use solid state controllers. The

use of unapproved controllers will void your warranty.

2. Do not mix blade sets from one fan to another as this may upset the balance of the fan. If

only one blade is damaged you are still required to replace with a new set.

STEP 3 (Fig. 3)

a) Check if the ball joint grub screw is tight.

b) Hang the ball joint into the hanger bracket.

Ensure the groove on the hanger bracket is

locked into the slot on the ball joint.

(This is important to ensure the fan will not

wobble and the weight of the fan is supported).

Assembling the fan

STEP 2 (Fig. 2)

a) Drill a hole in the timber nogging for wiring.

b) Secure the hanger bracket onto the timber

nogging, using the two hex head screws

provided. The timber nogging should be supplied

by the installing electrician and must be

supported between the two ceiling joists as

shown in the diagram above.

STEP 1 (Fig. 1)

PERFORM THIS STEP IF THE WIRES HAVE NOT

BEEN FED THROUGH THE DOWN ROD.

a) Loosen the ball joint screw and remove the

ball joint pin to separate the down rod from the

ball joint.

b) Feed wires from motor housing up and

through the down rod.

c) Insert the down rod pin screw through the

connection collar and the down rod (avoid

pinching wires). Tighten down rod pin screw.

Secure down rod with the other shorter down

rod screw provided.

d) Slide on canopy cover, refit the ball joint and

tighten grub screw.

Hanger

Bracket

Down Rod

Fig. 2

Timber Nogging

Hex Head Screw

Hanger

Bracket

Fig. 3

Down Rod

Pin Screw

Canopy

Cover

Connection Collar

Motor

Housing

Fig. 1

Electrician Installation Manual

Concept Ceiling Fan

(Timber and Moulded Blades)

1. Do not attempt to operate the fan (or optional light kit) with any wall control that is not

approved by Hunter Pacific for use with its fans. DO NOT use solid state controllers. The

use of unapproved controllers will void your warranty.

2. Do not mix blade sets from one fan to another as this may upset the balance of the fan. If

only one blade is damaged you are still required to replace with a new set.

(Assembling the fan )

Fig. 4

Green

Earth Wires

STEP 4 (Fig 4 & 5)

a) Connect wires from the fan to wires in the

ceiling via the terminal block on the hanger

bracket (refer to figure 4 and 5).

b) Make sure earth wires are also connected.

c) Connect light wires (red/white) if a light

fitting is going to be used. (Cap seal light

wires if a light fitting is not going to be used).

Wiring Instructions (with and without accessory light)

Brown

Blue

Red/White Earth Wires

Supply

E N A

LA LA

FA LA E N

Green-yellow

Black

Red

Brown

White or Red

Green-yellow

Blue

Fan Wiring

Combi

Control

Separate

Control

Separate terminal

For when 3 pole

block is fitted.

Wiring for use with 3 pole block

- Colours representative only

- Separate terminal required active for

light when 3 pole block fitted.

Fig. 5

STEP 5 (Fig 6)

a) Slide canopy cover up and over the hanger

bracket.

b) Loosen the canopy to locate screws holes then

loosen canopy screws half way.

c) Now twist the canopy cover in the opposite

direction and fully tighten screws until the canopy

cover is stabilized.

Fig. 6

Hanger Bracket

Canopy

Canopy Cover Screws

Electrician Installation Manual

Concept Ceiling Fan

(Timber and Moulded Blades)

1. Do not attempt to operate the fan (or optional light kit) with any wall control that is not

approved by Hunter Pacific for use with its fans. DO NOT use solid state controllers. The

use of unapproved controllers will void your warranty.

2. Do not mix blade sets from one fan to another as this may upset the balance of the fan. If

only one blade is damaged you are still required to replace with a new set.

Assembling the fan

Canopy

Screw Cover

STEP 6 (Fig 7)- Concept 2 fan ONLY

Move the canopy screw cover upwards towards the

canopy and turn it to secure the cover onto the screw

heads.

Fig. 7

Fig. 8 STEP 7 (Fig 8)

a) Push the base plate upwards and turn until the

tabs unlock to remove it.

b) Once the base plate is removed, the internal

blade carriers will be exposed. Insert blades and at-

tach them to the motor housing as shown in figure 8.

c) Tighten the 3 blade screws firmly but do not over

tighten.

d) Install blades for each fan individually, do not mix

blades from different fans as this will up set the bal-

ance of the fan.

Blade

Blade Screw

Motor Housing

tabs

Base Plate

Fig. 9

Tab slots

Tabs

Base Plate

STEP 8 (Fig. 9)

a) Once all blades are attached to the motor

housing, refit the base plate. The tabs

should lock in to place ensuring the base

plate is securely attached to the motor

Fig. 10

Reverse

Switch

STEP 9 (Fig. 10)

a) Reverse switch should be in the down position

for Summer (fan spins anticlockwise) and in the

up position for Winter (fan spins clockwise).

b) Make the sure reverse switch is not stuck in its

neutral position otherwise the fan will not spin.

Electrician Installation Manual

Concept Ceiling Fan

(Timber and Moulded Blades)

1. Do not attempt to operate the fan (or optional light kit) with any wall control that is not

approved by Hunter Pacific for use with its fans. DO NOT use solid state controllers. The

use of unapproved controllers will void your warranty.

2. Do not mix blade sets from one fan to another as this may upset the balance of the fan. If

only one blade is damaged you are still required to replace with a new set.

Attaching a Concept light kit - 78mm halogen light (MAX 100W)

Fig. 12

Tab

Slots

Light Wires

Light

Assembly Kit

Globe

STEP 2 (Fig. 12)

a) Use the connectors to attach the light wires from

the motor housing to the light wires on the light

assembly.

b) Secure the light assembly kit using the 3 screws

provided.

c) Plug the light globe into the socket. DO NOT

touch the light globe with your fingers, use a

tissue or a clean cloth. It is extremely important

to keep the globe clean. If the globe is dirty, clean

it carefully with a cloth or tissue. Dirt on the globe

will cause it to fail almost immediately.

NOTE: Do not use globes other than the specified

ones.

Motor

Housing

Tab

Slots

Tabs

Base Plate

STEP 1 (Fig. 11)

Push the base plate upwards and turn until the

tabs unlock to remove it.

Fig. 11

Screw

Light

Kit Ring

Light

Rim

Fig. 13 STEP 3 (Fig. 13) - Concept 2 fan ONLY (pre Nov

2008 Only)

a) Remove the screws attached to the light rim.

b) Remove the light kit ring from the light rim.

P.S . Adaptor ring not required for New

Concept 1 or New Concept 2 (Nov 2008)

Electrician Installation Manual

Concept Ceiling Fan

(Timber and Moulded Blades)

1. Do not attempt to operate the fan (or optional light kit) with any wall control that is not

approved by Hunter Pacific for use with its fans. DO NOT use solid state controllers. The

use of unapproved controllers will void your warranty.

2. Do not mix blade sets from one fan to another as this may upset the balance of the fan. If

only one blade is damaged you are still required to replace with a new set.

Attaching a Concept light kit - 78mm halogen light (MAX 100W)

Tab

Slots

Glass Cover

Fig. 16

Tabs

STEP 6 (Fig. 16)

a) Once globe is placed into its socket properly,

the glass cover can be fitted on to the fan.

b) Gently push the glass cover upwards and turn it.

The tabs should lock in to place ensuring the glass

cover is securely attached to the motor housing.

Light

Kit Ring

Light

Rim

Adaptor

Ring

Fig. 14 STEP 4 (Fig. 14) - Concept 2 fan ONLY

a) Place the adaptor ring on the light rim.

b) Place the light kit ring on the adaptor ring.

Light

Rim

Screw

Adaptor

Ring

Fig. 15 STEP 5 (Fig. 15) - Concept 2 fan ONLY

Use screws to attach the light ring and adaptor

ring firmly to the light rim.

Electrician Installation Manual

Concept Ceiling Fan

(Timber and Moulded Blades)

1. Do not attempt to operate the fan (or optional light kit) with any wall control that is not

approved by Hunter Pacific for use with its fans. DO NOT use solid state controllers. The

use of unapproved controllers will void your warranty.

2. Do not mix blade sets from one fan to another as this may upset the balance of the fan. If

only one blade is damaged you are still required to replace with a new set.

Attaching a Concept light kit - E14 light (2x40W)

Tab

Slots

Tabs

Base Plate

STEP 1 (Fig. 17)

Push the base plate upwards and turn until the

tabs unlock to remove it.

Fig. 17

Fig. 18

Tab

Slots

Light Wires

Light

Assembly Kit

Globe

STEP 2 (Fig. 18)

a) Use the connectors to attach the light wires from

the motor housing to the light wires on the light

assembly.

b) Secure the light assembly kit using the 3 screws

provided.

c) Install light globes into the light sockets.

Motor

Housing

Screw

Light

Kit Ring

Light

Rim

Fig. 19 STEP 3 (Fig. 19) - Concept 2 fan ONLY (pre Nov

2008 Only)

a) Remove the screws attached to the light rim.

b) Remove the light kit ring from the light rim.

P.S . Adaptor ring not required for New

Concept 1 or New Concept 2 (Nov 2008)

Electrician Installation Manual

Concept Ceiling Fan

(Timber and Moulded Blades)

1. Do not attempt to operate the fan (or optional light kit) with any wall control that is not

approved by Hunter Pacific for use with its fans. DO NOT use solid state controllers. The

use of unapproved controllers will void your warranty.

2. Do not mix blade sets from one fan to another as this may upset the balance of the fan. If

only one blade is damaged you are still required to replace with a new set.

Attaching a Concept light kit - E14 light (2x40W)

Light

Kit Ring

Light

Rim

Adaptor

Ring

Fig. 20 STEP 4 (Fig. 20) - Concept 2 fan ONLY

a) Place the adaptor ring on the light rim.

b) Place the light kit ring on the adaptor ring.

Light

Rim

Screw

Adaptor

Ring

Fig. 21 STEP 5 (Fig. 21) - Concept 2 fan ONLY

Use screws to attach the light ring and adaptor

ring firmly to the light rim.

Fig. 22

STEP 6 (Fig. 22)

a) Once globes are installed, the glass cover can

be fitted on to the fan.

b) Gently push the glass cover upwards and turn

it. The tabs should lock in to place ensuring the

glass cover is securely attached to the motor

housing.

Tab

Slots

Glass Cover

Other manuals for Concept

This manual suits for next models

Table of contents

Other Hunter Pacific Fan manuals

Hunter Pacific

Hunter Pacific Majestic Palm User manual

Hunter Pacific

Hunter Pacific Coolah Instruction Manual

Hunter Pacific

Hunter Pacific Attitude User manual

Hunter Pacific

Hunter Pacific Majestic Rosewood User manual

Hunter Pacific

Hunter Pacific Majestic Duo User manual

Hunter Pacific

Hunter Pacific THE WOOD Series Owner's manual

Hunter Pacific

Hunter Pacific Majestic Madagascar User manual

Hunter Pacific

Hunter Pacific AQUA DC AIP2661 Instruction Manual

Hunter Pacific

Hunter Pacific RADICAL 2 Instruction Manual

Hunter Pacific

Hunter Pacific Intercept II User manual

Hunter Pacific

Hunter Pacific Majestic Penta User manual

Hunter Pacific

Hunter Pacific Typhoon Mach 2 Timber User manual

Hunter Pacific

Hunter Pacific Icon Fan User manual

Hunter Pacific

Hunter Pacific POLAR DC P3B2571 Instruction Manual

Hunter Pacific

Hunter Pacific Majestic Everglade User manual

Hunter Pacific

Hunter Pacific X-OVER DC Instruction Manual

Hunter Pacific

Hunter Pacific Majestic Coolah User manual

Hunter Pacific

Hunter Pacific Typhoon Timber 42" User manual

Hunter Pacific

Hunter Pacific Majestic Magnum User manual

Hunter Pacific

Hunter Pacific Icon 52 User manual

Hunter Pacific

Hunter Pacific Concept Quick start guide

Hunter Pacific

Hunter Pacific Majestic Little Bay User manual

Hunter Pacific

Hunter Pacific Majestic Micro User manual

Hunter Pacific

Hunter Pacific VortX V500i Installation guide

Popular Fan manuals by other brands

ELTA FANS

ELTA FANS H03VV-F installation guide

Hunter

Hunter 20714 Owner's guide and installation manual

Emerson

Emerson CARRERA VERANDA CF542ORB00 owner's manual

Hunter

Hunter Caraway Owner's guide and installation manual

Panasonic

Panasonic FV-15NLFS1 Service manual

Kompernass

Kompernass KH 1150 operating instructions

VES

VES FALA100/12V/TR Original instructions

Vertiv

Vertiv Liebert DCD user manual

Westinghouse

Westinghouse GFP Series owner's manual

Venmar

Venmar KUBIX HRV PLUS Series user guide

Maico

Maico ECR 31 installation instructions

Sonnenkonig

Sonnenkonig Dinky instruction manual

S&P

S&P ECOWATT HXBR manual

Wider

Wider IMP03369BH instruction manual

Panasonic

Panasonic F-60DHN Operating and installation instructions

Hinkley

Hinkley HIGHLAND instruction manual

Broan

Broan 766BN installation guide

Premium

Premium PFS16022 Use manual