Huawei E5830 User manual
1
Thank you for choosing this Wireless Terminal
(hereinafter referred to as the device).
Note:
zThe supported functions and actual appearance are subject to your product
purchased. The following pictures are displayed for illustration purpose only. For
details of your product selection, consult your service provider.
zThis guide briefly describes the function of the device. For the operation of
configuring the management parameters, see Help on the management program or
web management page.
zThe device can be used in a reasonable closed environment such as a pocket,
handbag or laptop bag, however if there is a risk that the ambient temperature will
increase when the device is processing data services for a long period, due to the
device not being able to dissipate the heat effectively. If this happens and as a safety
precaution the device will switch off automatically or disconnect. In the event of this
happening please restart your device as usual to restart the connection.
2
1. Get to Know Your Device
1. USB connector
2. Micro SD card slot
3. Battery_button
4. Power On/Off
5. WiFi/WPS button
6. Dialing button
7. Signal indicator
8. Roam indicator
9. WiFi/WPS indicator
10. Mode indicator
11. Battery indicator
zWiFi: Wireless Fidelity
zWPS: WiFi Protected Setup
3
Indicator Status
zSteady on and in red: The USIM/SIM card does not exist or the PIN
code is not verified or the signal is inexistent.
zSteady on and in yellow: The signal strength is weak.
zSteady on and in green: The signal strength is strong.
zOff: The device is not in the roaming state.
zSteady on and in red: The device is in the roaming state.
zOff: The WiFi and WPS are disabled.
zSteady on and in blue: The WiFi is enabled.
zFast Blinking in blue: The WPS is enabled.
zOff: The network service is inexistent.
zFast blinking in green: dialing up.
zBlinking in green: 2G network registered.
zSteady on and in green: 2G data service connected.
zBlinking in blue: 3G network registered.
zSteady on and in blue: 3G data service connected.
4
Indicator Status
zFast blinking in red: The battery power level is very low and must be
charged immediately; otherwise the device will be powered off.
zSteady on and in red: The battery power level is weak.
zSteady on and in green: The battery power level is enough.
zBlinking: The battery is being charged. If the indicator is in red, the
battery level is too low to power on the device. When the indicator
turns green, you can power on the device.
2. Prepare the Device
Install the USIM/SIM Card and Battery
Position the card at the card slot entrance, making sure it is facing the same way as show
in the diagram, with the notched corner at the top left. Then slide in.
5
Power on the Device
Press and hold until the indicators become
lightened; the device is powered on.
Note: Press and hold until the indicators are
off; the device is powered off.
6
3. How to Access the Internet with
WiFi
Step1. Establish the WiFi Connection (Take PC
for Example)
1. Select Start > Control Panel > Network
Connections > Wireless Network
Connection.
Note: To set up a WiFi connection, the PC
must be configured with the wireless
network adapter. If the wireless network
connection is displayed, the wireless network
adapter is available. Otherwise, you should
check your wireless network adapter.
2. Click View available Wireless Networks to display the wireless network connection list.
7
3. Select the network connection that the
SSID is the same as that of the device, and
then click .
Note:
zIf the encryption parameter is set for the
device, the Wireless Network Connection
dialog box is displayed and requires
the network key and confirmation.
zThe SSID and key label is attached on
the device.
Wait for a while. The wireless connection icon displays in the status area in the lower right
corner of the screen. Then, your PC can automatically connect to the device.
Step2. Access the Internet
By default, the device automatically dials up to access the Internet. You can directly use the
Internet service.
If the Internet service does not respond, you can access the Internet using the dialing
8
button manually.
Press and hold until is blinking, the
connection is set up successfully. Then you can use the
Internet service.
Note: Press and hold until is off, the connection is tore down.
4. How to Install the Management Program
The procedure for installing the
management program depends on the
operating system installed on your PC. The
following section takes Windows XP as an
example.
1. Power on the device.
2. Connect the device and PC with the compatible data cable.
3. The OS (Operating System) automatically detects and recognizes new hardware and
starts the installation wizard.
Note: If the auto-run program does not respond, find the installing file in the driver path.
9
Then double-click the installing file to run the program.
4. Follow the prompts of the installation wizard.
5. After the program is installed, the shortcut icon of the program is displayed on the
desktop.
6. After the device is installed, the program is launched automatically. Then every time
the device is connected to the PC with the compatible data cable, the program is
launched automatically.
Note: You can also double-click the shortcut icon on the desktop to launch the program.
5. How to Access the Web Management Page
1. Start the Internet browser and enter http://192.168.1.1 in the address bar.
2. Enter the password, and then click Login.
zAdmin: This user type is authorized to view and change configurations. The default
password is admin.
Note: If the page is unavailable while the device is being connected with PC through the
compatible data cable, launch the management program and then access the web page.
10
6. Everyday Use
Charging the Battery
Note: If you have not used the battery for a long time,
please recharge it first.
Method 1: Using the charger
Caution:
zUse the compatible charger delivered only by the manufacturer with this device model.
Using charger of other device model, other manufacturers or vendors may invalidate
any approval or warranty applicable to the device, result in the non-operation of the
device, and cause danger.
zCharger is an optional accessory. If the charger is not provided in the package, you
can contact your service provider to buy one yourself.
Method 2: Connecting to a PC for charging
1. Power off the device.
2. Connect the device and PC with the compatible data cable.
Other manuals for E5830
2
Table of contents
Other Huawei Touch Terminal manuals
Huawei
Huawei ETS2059 User manual
Huawei
Huawei OptiXstar K153-10 User manual
Huawei
Huawei B160 User manual
Huawei
Huawei EP650 Series User manual
Huawei
Huawei ETS2555 User manual
Huawei
Huawei EchoLife HG8240 User manual
Huawei
Huawei EchoLife HG8245 Technical specifications
Huawei
Huawei DBS3900 GSM User manual
Huawei
Huawei EchoLife OT925-G User manual
Huawei
Huawei HG8120 series User manual
Huawei
Huawei ETS2018 User manual
Huawei
Huawei ETS3053 User manual
Huawei
Huawei ETS1160 User manual
Huawei
Huawei FT2050 User manual
Huawei
Huawei F316 Installation guide
Huawei
Huawei ETS2226 User manual
Huawei
Huawei ETS3023 User manual
Huawei
Huawei EchoLife HG8245 User manual
Huawei
Huawei ETS2225 User manual
Huawei
Huawei EchoLife HG8110 User manual
