Huawei PTN Series User manual

HUAWEI TECHNOLOGIES CO., LTD.

OptiX PTN 910E-F Packet Transport Platform of PTN Series

Quick Installation Guide

Issue: 04

Date: 2020-03-31

No part of this document may be reproduced or transmitted in any form or by any means without prior

written consent of Huawei Technologies Co., Ltd.

Trademarks and Permissions

and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.

All other trademarks and trade names mentioned in this document are the property of their respective

holders.

Notice

The purchased products, services and features are stipulated by the contract made between Huawei and

the customer. All or part of the products, services and features described in this document may not be

within the purchase scope or the usage scope. Unless otherwise specified in the contract, all statements,

information, and recommendations in this document are provided "AS IS" without warranties, guarantees or

representations of any kind, either express or implied.

The information in this document is subject to change without notice. Every effort has been made in the

preparation of this document to ensure accuracy of the contents, but all statements, information, and

recommendations in this document do not constitute a warranty of any kind, express or implied.

Huawei Technologies Co., Ltd.

Address:

Huawei Industrial Base

Bantian, Longgang

Shenzhen 518129

People's Republic of China

Website:

http://www.huawei.com

Email:

[email protected]

Installation Precautions

Tools for Installation

Measuring tape Phillips screwdriver

Marker Installation gloves

Flat-head screwdriver

Wire stripper RJ45 crimping tool Optical power meter Binding strap Insulation tape

Hammer drill Claw hammer

This document provides simple and distinctive guidelines for quick hardware installation of the PTN 910E-F.

This document does not describe pre-delivery assembly, but only describes procedures for onsite installation.

The PTN 910E-F supports indoor installation. Ensure that requirements on device operating environments are met before

installation. Using the outdoor cabinet IMB network box can moderately improve the device operating environment. If you need to

use an outdoor cabinet other than the IMB network box for the PTN 910E-F, contact Huawei to determine whether the outdoor

cabinet meets requirements of Huawei devices on the device operating environments.

Pre-Installation Check

Before installation, check whether the installation environment and accessories meet installation

requirements. Refer to the Installation Guide for information about specific operational requirements and

technical specifications.

NOTE

CAUTION

Laser beams from optical fibers may harm your eyes. Do not look into the optical interfaces without

eye protection when performing operations such as installing and maintaining optical fibers.

DANGER

Network cable tester Diagonal pliers Multimeter

Heat gun Paper knife Torque screwdriver

OptiX PTN 910E-F Appearance

Common Requirements for Installing, Laying out, and

Bundling Cables

The space between power cables, network cables, and optical fibers must be greater than 30 mm.

Power cables, network cables, and optical fibers cannot be interleaved but must be routed in parallel or separated with specific stuffs.

When cables are fixed or bound, the interval between two cable ties cannot exceed 40 cm.

When cables are bent, the bending radius is recommended to be greater than 60 mm and cables are not bundled at the turning

points.

The bending radius of optical fibers is no less than 40 mm. Do not pull, press, or squeeze optical fibers during installation.

Gently coil excess optical fibers. Do not forcibly bend the optical fibers.

Do not power on the device when installing and laying out cables.

FE/GE optical interface

Power supply interface External clock interface

XGE optical interface

ESD wrist strap

Time interface

ETH/OAM interface

Equipotential bonding point

Boolean interface

When the PTN 910E-F operates, switches of two AC

power modules in 1+1 backup mode are enabled and in

ON status, as shown in the right figure.

For details about interfaces on different types of PTN

910E-F routers, see the hardware description.

NOTE

XGE/GE/FE optical

interface ( These interfaces cannot be switched to work at the rate of 10 Gbit/s )

The current status is OFF.

DCN Interface Distribution

DCN interfaces are

enabled by default.

NOTE

By default, DCN is enabled on the first four

interfaces in the four optical interface areas.

1Scenario 1: Installing the Chassis in a 19-Inch Rack

When tightening floating nuts, keep a distance of at least

50 mm on both the left and right sides of the PTN 910E-

F for proper ventilation.

Mounting holes of

floating nuts: Three

equidistant holes

are 1 U height. A 1

U device

corresponds to

holes 1 to 3.

Floating nut

Floating nut hook

( can be replaced using

a flat-head screwdriver. )

2.0 ±0.2 N·M

cInstalling the PGND cable

There are holes for ground screws on the column of the cabinet. One end of thePGND cable is

fastened to the device, and the other end can be fastened to the nearest grounding point or to the

indoor ground bar according to the actual situation.

NOTE

Tightening the floating nut

aInstalling the chassis in the rack

1.4 ±0.14 N·M

Align mounting ears with mounting holes of floating

nuts and screw the chassis.

Reserve at least 1 U vertical space above and below

the chassis for heat dissipation.

Installing the Chassis

Take ground screws out of the fitting bat and screw one end of

the PGND cable.

2Scenario 2: Installing the Chassis in an ETSI Rack

One or two holes

correspond to 1 U

height.

Floating nut

Floating nut hook

( can be replaced using

a flat-head screwdriver. )

2.0 ±0.2 N·M

Tightening the floating nut

aInstalling the rack-mounting ear

When tightening floating nuts, keep a distance of at least

50 mm on both the left and right sides of the PTN 910E-

F for proper ventilation.

ETSI rack

25 mm

Rack-

mounting ear:

Installing the chassis

cInstalling the PGND cable

Align mounting ears with mounting holes of

floating nuts and screw the chassis.

Reserve at least 1 U vertical space above and

below the chassis for heat dissipation.

NOTE

2.0 ±0.2 N·M

1.4 ±0.14 N·M

M6 combination screws with spring and flat washers

Take ground screws out of the fitting bat to

install the PGND cable.

There are holes for ground screws on the column of

the cabinet. One end of the PGND cable is fastened

to the device, and the other end can be fastened to

the nearest grounding point or to the indoor ground

bar according to the actual situation.

Installing Cables

1Common Cables

PGND cable AC power cable DC power cable Fiber

Shielded network cable E1 cable ( 120-ohm ) E1 cable ( 75-ohm )

2Installing the Power Cable

Connecting the AC power cable

aConnecting the DC power cable

Power cable locking strap

•After the power plug is inserted, use the power cable

locking strap to fasten the plug connected to the device,

preventing the plug from getting loose or falling off.

•When laying out power cables, ensure that power

cables are separated from other cables ( E1 cable,

optical fiber, and network cable ). Generally, power

cables are laid out on the left and signal cables are laid

out on the right.

•Two AC power supply modules must be installed on

the PTN 910E-F.

NOTE

Screw the OT terminal of the DC power cable to

the DC power interface.

The conductive part of the power

cable must be completely connected

to the DC connector to prevent

personal injury caused by discharge.

0.4 ±0.5 N·M

M2.5

WARNNING

Install network cables.

Network cables include service

and auxiliary network cables.

Install optical fibers.

The bending radius of optical fibers must be greater than its minimum curvature radius.

The minimum curvature radius of 2 mm optical fibers is 40 mm.

3Installing Optical Fibers

Install cables in the following sequence. Install cables of the same type from the left to the right.

After service network cables are installed, you need to check the connectivity of cables.

When installing cables, place power cables towards the left and signal cables towards the right.

光纤

网管网线

When installing or maintaining optical fibers, do not look into the optical port without eye protection. See

Figure 1.

When laying out optical fibers, take proper measures to avoid any damage to fiber connectors.

After optical fibers are installed, place protective caps on the idle optical interfaces and place fiber caps on

the idle optical fibers. See Figure 2.

The type of the fiber connector is LC/PC.

Fiber cap

Pluggable optical

module

Dustproof cap

Figure 1 Figure 2 Fiber with a short

protective tube

CAUTION

NOTE

Optical fiber

NMS cable

3Installing Optical Fibers

NOTE

Inner pipe

Outer pipe

CAUTION

Wrap both ends of the corrugated pipe using tapes to prevent optical fibers from being cut.

Do not use an open-end corrugated pipe to

hold excessive optical fibers. It is

recommended that an open-end

corrugated pipe that has a diameter of 32

mm accommodates 60 optical fibers at

most, each with a diameter of 2 mm.

Ensure that about 10 cm of the open-end

corrugated pipe is inside the cabinet.

Network

cable Side A Side B

Straight

through

network

cable

The indicators at points 1,

8, and G turn on in

sequence.

The indicators at points 1, 8,

and G turn on at the same

time.

Crossover

cable The indicators at points 1,

8, and G turn on in

sequence.

The indicators at points 3, 6,

1, 4, 5, 2, 7, 8, and G turn on

at the same time.

Side B

Side A

You can also use the method of looping back Ethernet interfaces ( applicable to the Ethernet interfaces on

a device that is powered on ) to check the connectivity of network cables. That is, connect two Ethernet

interfaces using the network cable to be tested. If the LINK indicator is on, the network cable is normal.

aChecking the connectivity of service network cables

NOTE

Checking Cable Connectivity

Other manuals for PTN Series

This manual suits for next models

Table of contents

Other Huawei Network Router manuals

Huawei

Huawei AR1200 Series User manual

Huawei

Huawei Quidway S3000-EI Series User manual

Huawei

Huawei Mobile WiFi Smart E355 User manual

Huawei

Huawei S6700 Series User manual

Huawei

Huawei AR532 User manual

Huawei

Huawei B818-263 User manual

Huawei

Huawei WiFi Mesh 3 User manual

Huawei

Huawei WS7001 User manual

Huawei

Huawei B593 User manual

Huawei

Huawei Quidway S3526 User manual

Huawei

Huawei quidway s7700 User manual

Huawei

Huawei LTE CPE B593 User manual

Huawei

Huawei Swisscom B593s User manual

Huawei

Huawei NE05E User manual

Huawei

Huawei LTE CPE B593 User manual

Huawei

Huawei AR2200 Series User manual

Huawei

Huawei LTE CPE E5172 Manual

Huawei

Huawei ADSL2+Broadband Router Aolynk DR814 User manual

Huawei

Huawei Vodafone B970 User manual

Huawei

Huawei B311-520 User manual

Huawei

Huawei AR2200 Series User manual

Huawei

Huawei B311s-220 User manual

Huawei

Huawei Vodafone B970 User manual

Huawei

Huawei B311As-853 Technical specifications

Popular Network Router manuals by other brands

Allnet

Allnet ALL0333AU user guide

HomeSeer

HomeSeer HT-SEL Getting started guide

Sercomm

Sercomm Genesis OC3505D Quick installation guide

Billion

Billion BIPAC 5102 Series user manual

TP-Link

TP-Link TD-8817 QIG

Motorola

Motorola MR1900 user guide

Digi

Digi IX14 user guide

Cisco

Cisco NCS 540 Hardware installation guide

XAVi

XAVi X8821e user manual

BEC

BEC 6200WZL Quick installation guide

MikroTik

MikroTik hAP ac3 Series quick start

Korenix

Korenix JetNet 5428G Series user manual

NETGEAR

NETGEAR FS526T - Switch installation guide

Korenix

Korenix JetNet 5710G Series user manual

Automated Logic

Automated Logic ZN551 Technical instructions

Cisco

Cisco ASR 1000 Series Installation and configuration guide

EnGenius

EnGenius ESR-9710 quick start guide

Cisco

Cisco 805 Series Product overview