Huawei PowerCube 500 User manual
1
Issue: 03
Date: 2018-06-20
PowerCube 500 V200R001C00 Quick Guide (ICC50)
Copyright © Huawei Technologies Co., Ltd. 2018. All rights reserved.
1Product Overview
ICC Interior
PV module PV module
support
Dome
camera
ICC50
Barrel
camera
Pole
Lightning rod
Cantilever
PoE
Space for transmission equipment
Network port SPD
Space for a PDU
Space for an inverter
DCDU-80A1
Space for ESMU
Space for batteries Heater
Barrel
camera
cable
Dome
camera
cable
ICC ground
cable
Mains AC cable,
optical fiber, ICC
ground cable,
camera cable,
CPE cable, and
PV module cable
CPE cable and PV
module cable
Dome
camera
ICC50
Barrel
camera
Support
Pole (a cabinet
can be installed on
the pole with BOM
number 21540285)
Lightning rod
Cantilever
CPE
Solar+Mains Scenario Mains Scenario Cable Holes on the Pole
CPE
2
2Tools
3Installing a Cantilever
Bottom Cable Holes
Ground cable,
signal cable,
DC cable and
hydrogen
discharge tube
Reserved
AC cable,
optical fiber,
PV DC cable,
and signal
cable
Cable Holes on the Partition Plate
DC cable
Ground
cable
Signal
cable
Optical fiber,
PV DC cable
Signal cable
AC cable
E-label cable,
ESMU-battery
signal cable
3
4Installing a Camera and Cables
Installing a Camera
4.1
For the camera installation method, see the documents delivered with the equipment.
Installing Camera Cables
4.2
For the cable connections at the camera side, see the documents delivered with the equipment. Reserve the other ends of cables.
5Installing PV Modules and Cables
Installing a PV Module Support
5.1
In the northern hemisphere, PV modules face south. In the southern hemisphere, PV modules face north.
1. Remove the connective kit. 2. Adjust the PV module direction based on
the PV module direction principles, and
then install the connective kit.
3. Adjust the PV module tilt angle based on the site
latitude, and secure the PV module support base.
Site
Latitude
(Degree)
PV Module
Tilt Angle
0
–15
15
°
16
–25
25
°
26
–30
35
°
31
–45
45
°
When installing beams,
keep the slots on the
beams face outwards to
facilitate operation.
4. Install the PV module support. 5. Measure the PV module
hole spacing L. 6. Determine the beam mounting holes based on L
and install the beams.
NOTICE
NOTE
4
Installing Two PV Modules
Installing Four PV Modules
Installing PV Modules
5.2
Adhesive tape
1. Install PV modules. 2. Install cables for the PV modules.
Adhesive tape
1. Install vertical beams. 2. Install supports.
3. Install PV modules. 4. Install cables for the PV modules.
5
6Installing a Lightning Rod
7Pole
Solar+Mains Scenario Mains Scenario
1. Install mains AC input
power cables.
Mains
3. Secure the pole to the foundation.2. Check whether the pole needs to be repainted.
Repaint the damaged area of the pole, and then
use the crane to hoist the pole to the foundation.
8Installing the ICC
1. Mark the mounting holes on the concrete floor
and then install the expansion bolts. 2. Secure the cabinet.
Nearest
ground
point
Tool
Pole BOM
Number
Torque
21540161,
21540155
M18 215
N·m
21540285,
21540068,
21540078
M24 500
N·m
21540069
M30 3000
N·m
Adjust the tilting angle of the lightning rod according
to the site latitude.
Site
Latitude
(Degree)
Lightning
Rod
Tilt
Angle
0
–15
15
°
16
–25
25
°
26
–30
35
°
31
–45
45
°
6
9Installing Components
Installing Modules
9.1
There are six types of
routers. The installation
of AR550 is used as an
example in steps 2 and 3.
Installing an AR550 Router
3. Install the ICC ground cable.
ICC ground cable
M48300N1 PSU slot PSU slot S4820G slot
PSU slots support the installation of the R4850G2 and
R4850N6.
The PSU, S4820G, and M48300N1 are installed in the
same way. The right figure shows how to install a PSU.
Installing a Router and Cables
9.2
1. Take out the tray. 2. Install a router.
When installing the
AR550C, AR550,
AR531, MA5621,
and MA5671, take
out the small tray.
When installing the
NE05E-SK, take
out the big tray.
MA5621 Router
3. Reinstall the tray. Installing an AR550C Router
Small tray Big tray
NOTE
NOTE
NOTE
7
Installing an MA5671 Router Installing an NE05E-SK Router
Installing an AR531 Router
Installing a Network Port SPD and Cables
9.3
4. Install the router communications cable. 5. Install router power cables.
FE
Router
Router power port
If a network port surge
protective device (SPD)
is configured, when
installing the signal
cable for the router,
route the signal cable
through the port on the
network port SPD and
then to the port on the
router.
When installing the NE05E-
SK router, remove the small
tray and install the NE05E-
SK on the big tray.
NOTE
NOTE
Installing an Inverter, a PDU, and Cables
9.4
1. Install the inverter and power distribution unit (PDU). 2. Install the ground cables for the inverter and PDU.
SPD
Router
Camera
8
Installing a PoE and Cables
9.5
Installing a CPE and Cables
9.6
3. Install cables between the inverter and PDU. 4. Install the alarm cable and power cables for the inverter.
1. Install the PoE and its power cables. 2. Install the PoE signal cable.
1. For the CPE installation method, see the
documents delivered with the equipment.
2. Install CPE cables.
The router is
optional.
Installing CPE Cables
NOTE
For details about how to prepare the CPE
power cable connector, see the appendix.
Installing Camera Cables
9.7
1. Install camera signal cables. 2. (Optional) Install alarm linkage cables
for the dome camera. 3. Install camera power cables.
Dome camera
Camera power port
Nearest cabinet
ground point
The router and PoE are
optional.
NOTE
NOTE
Router
Camera
Router
Router Camera
9
10 Installing Batteries and Battery Cables
Installing Lead-Acid Batteries and Cables
10.1
Installing the TCB-60C and Cables
1. Install cables at battery terminals. 2. Remove the battery baffle bars. 3. Install the two
inner batteries
and reinstall
the battery
baffle bars.
Install the negative
battery cable before
installing the positive
battery cable.
4. Install the two outer batteries and reinstall
the battery baffle bars. 5. Install battery cables.
NOTICE
Installing the TCB-100C/FCB-100B and Cables
1. Remove the battery baffle bars. 2. Install batteries and reinstall the baffle bars. 3. Install copper bars between batteries.
10
Installing Lithium Batteries and Cables (ESU-A2400Wh/D)
10.2
4. Install battery cables.
1. Turn off the energy storage management unit (ESMU)
power switch and install the ESMU and ESU-A. 2. Set the ESMU address using the DIP switch and CAN DIP switch.
5. Install a hydrogen discharge tube.
Routing the
hydrogen
discharge
tube out of
the cabinet
COM2
COM_IN
COM_OUT
COM_IN
COM_ELU
COM_ELU IN
3. Install the ESMU signal cables. 4. Install signal cables between the ESU-As and ESMUs.
5. Install ESMU power cables. 6. Install the negative ESU-A power cables.
Other manuals for PowerCube 500
3
This manual suits for next models
1
Table of contents
Other Huawei Inverter manuals
Huawei
Huawei SUN2000 Series User manual
Huawei
Huawei SUN2000-5KTL-L0 User manual
Huawei
Huawei MERC Series User manual
Huawei
Huawei SUN600-5KTL-L0 User manual
Huawei
Huawei SUN2000-45KTL-US-HV-D0 User manual
Huawei
Huawei SUN2000-42KTL User manual
Huawei
Huawei SUN2000-45KTL-US-HV-D0 User manual
Huawei
Huawei SUN2000-50KTL-NHM3 User manual
Huawei
Huawei SUN2000-33KTL-A User manual
Huawei
Huawei SUN2000-(25KTL, 30KTL)-US User manual
Huawei
Huawei SUN2000L-2KTL User manual
Huawei
Huawei SmartGuard 63A-S0 User manual
Huawei
Huawei SUN2000-55KTL-HV-D1 User manual
Huawei
Huawei SUN2000-185KTL-INH0 User manual
Huawei
Huawei SUN2000-50KTL-JPM1 User manual
Huawei
Huawei SUN2000-4.95KTL-NHL2 User manual
Huawei
Huawei UPS5000-H-400K-FT User manual
Huawei
Huawei SUN2000-8KTL-M2 User manual
Huawei
Huawei SUN2000-90KTL User manual
Huawei
Huawei SmartPSB2000L User manual
