HP AT-BT10 User manual

AT-BT10 Snap Mount Kit

Installation Guide

0512016-01 | June 2017 1

Introduction

The AT-BT10 Snap Mount Kit includes 25 plastic mounting brackets for installing your BT10 Series

devices to mobile objects using a zip tie, or use screws to attach them flat surfaces.

Refer to the following section for complete installation instructions.

Installing the AT-BT10 Snap Mount

Before installing your AT-BT10 Snap Mount, ensure that the installation location does not come into

contact with other objects that may cause damage to this mount or the device.

To mount this kit to a flat surface, refer to Mounting to a flat surface.

To mount this kit to an object using a zip tie, refer to Mounting with a zip tie.

Mounting to a flat surface

1. Choose the desired location for installation, then mark and pre-drill a pilot hole.

2. Align the hole at the center of the plastic bracket with the pre-drilled hole in the mounting surface,

then screw it into place.

Mounting with a zip tie

1. Choose the desired location for your installation, making sure that your zip tie is the correct length

and width.

2. Position the plastic mounting bracket vertically so that the arrow located on the front of the

bracket points up, then thread the zip tie through the openings located on the sides of the

bracket. The zip tie should align horizontally after inserted into the mount. See Figure 1.

Figure 1 Inserting the zip tie into the mount

Screws and zip ties are not provided in this kit. The type/size of these items vary depending upon

the mounting surface. The recommended screw for this kit is a #4 flat head screw.

2AT-BT10 Snap Mount Kit | Installation Guide

3. Place the plastic mounting bracket flat against the surface of the mounting surface, wrap both

ends of the zip tie around the object. Insert the small end into the larger locking end and pull it

through. Adjust the position of the mount if necessary, then pull the small end of the zip tie until it

is firmly fastened around the object.

4. Activate the device, insert a coin into the indention located at the center of the rear panel, then

turn clockwise until the indicator arrow is aligned with the “I” marking. See 3..

Figure 2 Activating the AT-BT10

5. Insert the device into the plastic bracket. See Figure 3.

Figure 3 Inserting the AT-BT10 into the bracket

6. (Optional) Once the device is securely fastened to the mount, insert a second zip tie through the

holes located on the top and bottom of the bracket to lock the device into the mount. Insert the

small end into the larger locking end and pull it through to lock the device into the mount.

© Copyright 2017 Hewlett Packard Enterprise Development LP

Table of contents

Other HP Rack & Stand manuals

Popular Rack & Stand manuals by other brands

Salamander

Salamander Acadia AC/W/L400/WH Assembly instructions

Fohhn

Fohhn VAT-09 Mounting instruction

ricoo

ricoo FS0522 quick start guide

AMSOIL

AMSOIL BMK-22 Installation and service instructions

Kargo Master

Kargo Master 48220 installation guide

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 installation instructions

ricoo

ricoo S1222 installation instructions

Ready-Set-Mount

Ready-Set-Mount RSMCM602 instruction manual

VidaBox

VidaBox VB MNT FFS2 installation guide

Welch Allyn

Welch Allyn 48960 Assembly instructions

Arkon

Arkon CM035-ST-2 installation instructions

PROEL

PROEL PLWIN60C user manual

Agilent Technologies

Agilent Technologies E2609B installation guide

Mustang

Mustang MV-ARM4 installation guide

Mounting Solutions

Mounting Solutions WRM-320 manual

Pyle

Pyle PMKSPAD1 manual

ShelterIt

ShelterIt 21208 installation instructions

SPL

SPL RackPack?4 1040 manual 