HP StorageWorks 2312 Guide

This manual suits for next models

1

Other HP Power Supply manuals

HP

HP D7171A - NetServer - LPr Installation and operation manual

HP

HP xw8600 - Workstation Operating instructions

HP

HP 6177B Service manual

HP

HP PSR750-A User manual

HP

HP 710B Parts list manual

HP

HP D7171A - NetServer - LPr User manual

HP

HP HPJ3136A Installation and operating manual

HP

HP Harrison 6516A Service manual

HP

HP 6259B User manual

HP

HP StorageWorks SN6000 User manual

HP

HP A3550A - High Availability Disk Arrays Model 20 Storage... User manual

HP

HP 6434B Service manual

HP

HP E3610A Service manual

HP

HP 6236B Service manual

HP

HP 721A Owner's manual

HP

HP StorageWorks 7110 - Virtual Array User manual

HP

HP PSR1800-56A User manual

HP

HP HPE Synergy 12000 Frame User manual

HP

HP BENCH Series Service manual

HP

HP 6012A Service manual

HP

HP 59501B Service manual

HP

HP 6826A Service manual

HP

HP UPS R/T3000 User manual

HP

HP J2962A Installation and operating manual

Popular Power Supply manuals by other brands

Monacor

Monacor PS-12CCD instruction manual

VOLTIMA

VOLTIMA MagicBox 15 Installation and operating instructions

Agilent Technologies

Agilent Technologies 6032A Service manual

Miller

Miller Auto Deltaweld 452 owner's manual

BCP

BCP PUOUBK How to install

HC

HC 2210 manual

Puls

Puls CT5.241 installation manual

OCZ

OCZ ZX1250W Technical specifications

iseg

iseg ECH 238 manual

Power

Power XXL A Series instruction manual

Agilent Technologies

Agilent Technologies 6631B Service manual

Renogy

Renogy PHOENIX 300 user guide

Epson

Epson Stylus Scan 2500 Product information sheet

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 manual

Puls

Puls MiniLine ML50.100 instruction manual

Puls

Puls AS-Interface SLA4.100 installation manual

Kenwood

Kenwood PS-60 instruction manual

Elmdene

Elmdene G1380xN-y-s Series manual

HP StorageWorks

2312/2324 Modular Smart

Array DC power supply

replacement instructions

© Copyright 2008 Hewlett-Packard Development Company, L.P.

First edition: November, 2008

The information in this document is subject to change without

notice.

Printed in China

www.hp.com

500919-001

About this document

This document details procedures for replacing a failed DC power

supply in an HP StorageWorks 2000 Family Modular Smart Array.

Before you begin

CAUTION:

Parts can be damaged by electrostatic discharge. Use proper

anti-static protection:

•Keep the replacement component in the ESD bag until needed

•Wear an ESD wrist strap grounded to an unpainted surface

of the chassis.

•If an ESD wrist strap is unavailable, touch an unpainted surface

of the chassis before handling the component.

•Never touch connector pins.

Verifying component failure

Check the DC Voltage/Fan Fault/Service Required (bottom) LED:

•Amber = Fault condition

Disconnecting a DC power cable

IMPORTANT:

Use only the DC power cables provided with your product.

1. Verify that the main breaker to the rack is shut off prior to

disconnecting any DC connections.

2. Verify that all enclosure power switches are off.

3. Loosen the cable-locking screws attaching the D-shell connector to

the power supply.

4. Disconnect the power cable from the power supply.

5. Turn on the main breaker to the rack.

Removing a power supply

1. Turn the thumbscrew until it is disengaged from the module.

2. Rotate the latch downward to disconnect the internal connector,

and slide the module out.

Page 1

Installing a DC power supply

1. Slide the module into the slot as far as it will go.

2. Press the latch upward to engage the module; turn the thumbscrews

ﬁnger-tight

3. Connect a DC power cable to each power supply using the

D-shell connector. Use the up arrow on the shell to ensure proper

positioning before tightening.

4. Tighten the screws at the top and bottom of the shell with a torque

between 1.7 N-m (15 lb-in) and 2.3 N-m (20 lb-in) to attach the

cable securely to the DC power sources.

5. Turn on the main breaker to the rack.

6. Turn on the enclosure power switches.

Verifying component replacement

After replacing the module, check that the Input Power Good LED is on

and the DC Voltage/Fan Fault/Service Required (bottom) LED is off.

Additional information

See the MSA2000 web site: http://www.hp.com/go/msa2000.

Page 2