HP Pavilion 8800 - Desktop PC User manual

HP 8800 Routers

FIPS Enclosure Installation Guide

art number: 5998-3449

Document version: 6P101-20120928

5998-3449

Legal and notice information

No part of this documentation may be reproduced or transmitted in

any form or by any means without prior written consent of

Hewlett-Packard Development Company, L.P.

The information contained herein is subject to change without notice.

HEWLETT-PACKARD COMPANY MAKES NO WARRANTY OF ANY

KIND WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT

LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE. Hewlett-Packard shall not be

liable for errors contained herein or for incidental or consequential

damages in connection with the furnishing, performance, or use of this

material.

The only warranties for HP products and services are set forth in the

express warranty statements accompanying such products and services.

Nothing herein should be construed as constituting an additional

warranty. HP shall not be liable for technical or editorial errors or

omissions contained herein.

Manual Version: 6P101-20120928

BOM: 3104A0C3

Part number: 5998-3449

Contents

HP A8800 routers FIPS kit installation guide ··················································1

Installing the FIPS enclosure ············································································ 1

Introduction to the FIPS enclosure·························································· 1

Installation tools and accessories ·························································· 3

Preparing for installation ········································································ 3

Installing the FIPS enclosure to the A8805/A8812···························· 4

Installing the FIPS enclosure to the A8808-V ······································· 8

Applying tamper evidence labels·································································11

Manual Version: 6P101-20120928

BOM: 3104A0C3

Part number: 5998-3449

HP A8800 routers FIPS kit installation

guide

WARNING

o avoid bodily injury and damage to the router components, turn off the

power supply of the router before you install the FIPS kit.

HP A8800 routers meet the requirements of the FIPS security level 2.

NOTE:

•

The installation procedure must be performed by qualified personnel.

•

Before installation, read

Compliance and Safety Manual

for the

compatible router of the FIPS enclosure.

Installing the FIPS enclosure

The installation procedures vary with the installation environment.

Introduction to the FIPS enclosure

IMPORTANT:

Only use the screws and hex bolts that are supplied in the FIPS

enclosure

to secure the opacity shields.

The FIPS enclosure for an HP A8805 or A8812 router has the

following components:

Manual Version: 6P101-20120928

BOM: 3104A0C3

Part number: 5998-3449

Product

Code Description Component

Installation

/adhesive

position

Quantity

•JG570A

(for an HP

A8805

router)

•JG572A

(for an HP

A8812

router)

Left-side

opacity

shield

assembly

•1 × opacity

shield

•2 × guide

rail

•6 × M3

countersunk-

head screw

Left 1

Right-side

opacity

shield

assembly

•1 × opacity

shield

•1 × upper

mounting

plate

•1 × lower

mounting

plate

•2 × M3

pan-head

screw

Right 1

Rear

opacity

shield

assembly

•1 × opacity

shield

•4 × hex bolt

•4 × M3

countersunk-

head screw

Rear 1

The FIPS enclosure for an HP A8808-V router has the following

components:

Manual Version: 6P101-20120928

BOM: 3104A0C3

Part number: 5998-3449

Product

Code Description Component

Installation

/adhesive

position

Quantity

JG571A

Top opacity

shield

assembly

•3 × opacity

shield

•3 × mounting

plate

•9 × M3

pan-head

screw

Top 1

Front opacity

shield

assembly

1 × opacity shield Front 1

Rear opacity

shield

assembly

1 × opacity shield Rear 1

Installation tools and accessories

Preparing for installation

•

Make sure the operating temperature is not higher than 40°C (104°F).

M3 pan-head screw

(supplied with the

FIPS enclosure)

Hex bolt

(supplied with the

FIPS enclosure)

Phillips screwdriver

(user-supplied) Diagonal pliers

(user-supplied)Needle-nose

pliers (user-

supplied)

Alcohol-based

cleaning pad

(user-supplied)

ESD-preventive

wrist strap (supplied

with the router)

M3 countersunk-

head screw

(supplied with the

FIPS enclosure)

Manual Version: 6P101-20120928

BOM: 3104A0C3

Part number: 5998-3449

•

Ensure enough clearance for installation.

•

Face the front of the chassis to locate the installation positions (left and

right).

•

Wear an ESD-preventive wrist strap and make sure it is well grounded.

•

If the router has been mounted on a rack, remove it from the rack.

Installing the FIPS enclosure to the

A8805/A8812

The installation procedures are the same for HP A8805 and A8812

routers. This example installs a FIPS enclosure for an HP A8805 router.

To install the FIPS enclosure to the A8805:

1. Unpack the left-side opacity shield assembly and take out one guide

rail.

2. Position the guide rail to align its three countersunk holes with the

unused screw holes on the top left side of the chassis, and secure the

guide rail to the chassis with M3 countersunk-head screws.

3. Mount the other guide rail to the bottom left side of the chassis in the

same way.

Manual Version: 6P101-20120928

BOM: 3104A0C3

Part number: 5998-3449

Figure 1 Mounting guide rails to the left side of the chassis

4. Slowly push the left-side opacity shield along the guide rails until it

stops and fasten the two captive screws.

Manual Version: 6P101-20120928

BOM: 3104A0C3

Part number: 5998-3449

Figure 2 Installing the left-side opacity shield

5. Clean the adhesive area on the top surface of the chassis with

alcohol-based cleaning pads.

6. Unpack the right-side opacity shield assembly and take out the upper

mounting plate.

7. Position the upper mounting plate to the adhesive area on the top right

of the chassis, and press down firmly on the mounting plate to ensure

its solid contact with the adhesive area.

8. Hang the right-side opacity shield to the upper mounting plate and

secure the shield to the chassis with M3 pan-head screws.

9. Install the lower mounting plate in the same way as described in step

Keep the mounting plates dwell 24 hours.

Manual Version: 6P101-20120928

BOM: 3104A0C3

Part number: 5998-3449

Figure 3 Installing the right-side opacity shield assembly

10. Unpack the rear opacity shield assembly and take out hex bolts.

11. Completely loosen the M3 countersunk-head screws on the rear side of

the chassis, and install hex bolts in proper holes.

12. Align the holes on the opacity shield with the holes of the hex bolts,

press the opacity shield against the rear panel, and use M3

Table of contents

Popular Network Router manuals by other brands

Allnet

Allnet ALL0333AU user guide

HomeSeer

HomeSeer HT-SEL Getting started guide

Sercomm

Sercomm Genesis OC3505D Quick installation guide

Billion

Billion BIPAC 5102 Series user manual

TP-Link

TP-Link TD-8817 QIG

Motorola

Motorola MR1900 user guide

Digi

Digi IX14 user guide

Cisco

Cisco NCS 540 Hardware installation guide

XAVi

XAVi X8821e user manual

BEC

BEC 6200WZL Quick installation guide

MikroTik

MikroTik hAP ac3 Series quick start

Korenix

Korenix JetNet 5428G Series user manual

NETGEAR

NETGEAR FS526T - Switch installation guide

Korenix

Korenix JetNet 5710G Series user manual

Automated Logic

Automated Logic ZN551 Technical instructions

Cisco

Cisco ASR 1000 Series Installation and configuration guide

EnGenius

EnGenius ESR-9710 quick start guide

Cisco

Cisco 805 Series Product overview