Hover-1 Beast Buggy User manual
ELECTRIC SCOOTER ACCESSORY
BEAST
BUGGY
Even if you have ridden a scooter for years, it is important for you
and every rider to read this manual before using this product.
ELECTRIC SCOOTER ACCESSORY
BEAST
BUGGY
Operation Manual HY-BST-BGY
*Images used in this manual may vary slightly from
the product and are for reference purposes only.
IMPORTANT: KEEP FOR FUTURE REFERENCE
1
HELMETS SAVE LIVES!
Always wear a properly tted helmet that complies with CPSC or CE safety standards
when you ride your scooter.
WARNING
Correct Fitting:
Make sure your helmet
covers your forehead.
Incorrect Fitting:
Forehead is exposed
and vulnerable to
serious injury.
2
This manual is designed to give you the information you need for the safe operation and maintenance of your
new Hover-1 Beast Buggy. Please read it thoroughly before riding your Hover-1 Beast Buggy.
Section One of this manual involves safety and Hover-1 Beast Buggy care. Understanding and following this
Information will help you and your Hover-1 Beast Buggy avoid injury or damage.
Section Two of this manual gives assembly and installation instructions for your Hover-1 Beast Buggy.
Section Three of this manual covers specic safety and operating instructions for your Hover-1 Beast Buggy.
Even if you are an experienced rider, you should review this section before your rst ride.
Section Four of this manual covers warranty specications of your Hover-1 Beast Buggy.
INTRODUCTION
WARNING
Make sure you read this complete manual before riding
your Hover-1 Beast Buggy. Failure to do so, or failure to
follow its guidelines could lead to serious injury or death.
3
HOVER-1 BEAST BUGGY DIAGRAM
SPECIFICATIONS
1. Seat
2. Handle Bars
3. Shock Absorbing Coils
4. Pedal Mounts
5. Hook and Loop Elastic Strap
6. Seat Frame
7. Locker
8. Frame Extension
9. Foot Rests
10. Caster Wheel
Compatibility: Most self-balancing electric scooters with 10” wheels
Max Load: See max load of your self-balancing scooter
Max Speed: See max speed of your self-balancing scooter
Tire Size: 8” swivel caster
Seat Material: PP
4
1
2
4
3
5
6
7
8
10
2
5
9
PARTS LIST
(1) Seat
(1) Seat Frame
(1) Frame Extension
(1) Left Handle Bar
(1) Caster Wheel
(1) Right Handle Bar
(6) Hook and Loop
Elastic Strap
(1) Wrench
(4) Small Foam Pad
(1) Allen Wrench Set
(2) Locker
(6) Large Screws
(4) Small Screws
(6) 8mm Nut
(6) Large Washers
5
ASSEMBLING YOUR HOVER-1 BEAST BUGGY
If you have questions or concerns about any of these steps, please feel free to contact our Customer Service
Team at www.hover-1.com. Someone will be in touch to walk you through these steps.
Carefully follow the steps shown on the following pages for assembling the Hover-1 Beast Buggy.
Remove all Hover-1 Beast Buggy contents from the box. Ensure all contents from the “Parts List” section are
accounted for.
1. Using the two large screws and washers, attach the handle bars to the appropriate sides of the seat frame as
shown below. Tighten with included Allen wrench.
6
2. Align the caster wheel to the screw holes in front of the frame extension. Secure the caster wheel in place using
the included Allen wrench, four large screws, four large washers and four nuts.
4. Attach the lockers onto the the seat frame and insert the frame extension into the seat frame. Adjust the frame
extention to preferred length. Secure the frame extension in place using the two lockers. You can tighten the
lockers if needed by adjusting the bolt.
7
locker
locker
Adjust bolt to tighten/loosen
lockers if needed
3. Align the holes of the seat with the seat frame.
Secure the seat in place using the included Allen
wrench and four small screws.
4. Your Hover-1 Beast Buggy is now
completely assembled and should look
like the below image.
8
If you have questions or concerns about any of these steps, please feel free to contact our Customer Service
Team at www.hover-1.com. Someone will be in touch to walk you through these steps.
Carefully follow the steps shown on the following pages for installing the Hover-1 Beast Buggy onto your
electric scooter. Read the remainder of this manual before riding your Hover-1 Beast Buggy.
Your Hover-1 Beast Buggy should be completely assembled prior to installing it onto your electric scooter.
Please refer to the “Assembling your Hover-1 Beast Buggy” section for assembling procedures.
1. Place the pedal mounts onto the foot pedals of your self-balancing scooter with the front wheel facing
forward. Ensure the pedal mounts are centered on the foot pedals of your scooter as much as possible.
INSTALLING YOUR HOVER-1 BEAST BUGGY
9
SPACE EVENLY
Other manuals for Beast Buggy
1
Table of contents
Other Hover-1 Scooter manuals
Hover-1
Hover-1 COMET EU-H1-COMT Operation instructions
Hover-1
Hover-1 All-Star User manual
Hover-1
Hover-1 MY FIRST E-SCOOTER User manual
Hover-1
Hover-1 Liberty User manual
Hover-1
Hover-1 H1-ACE4 PRO ACE R450 User manual
Hover-1
Hover-1 EAGLE 3.0 User manual
Hover-1
Hover-1 Gambit User manual
Hover-1
Hover-1 H1 User manual
Hover-1
Hover-1 JOURNEY User manual
Hover-1
Hover-1 PRO Series User manual
Hover-1
Hover-1 DREAM User manual
Hover-1
Hover-1 AXLE User manual
Hover-1
Hover-1 Journey H1-JNY User manual
Hover-1
Hover-1 All-Star User manual
Hover-1
Hover-1 Buggy User manual
Hover-1
Hover-1 HY-H1 User manual
Hover-1
Hover-1 EAGLE EU-H1-EGE Operation instructions
Hover-1
Hover-1 Go-Kart User manual
Hover-1
Hover-1 HORIZON HY-H2L User manual
Hover-1
Hover-1 RENEGADE User manual
