Hotcig RSQ User manual
POWERED BY
1
Thank you for choosing RSQ BF Box Mod which
designed & manufactured by Hotcig. In order to get the
best vaping experience, be sure to read the instructions
and precautions carefully. In addition, please keep this
Instruction Manual for further reference if necessary.
RSQ BF Mod is R-Series product from Hotcig,
powered by 80w HM chip, designed to be BF/ Squonker
mod, and continues the style of replaceable panels.
Three output modes: Power Mode, Temperature
Control Mode, and BYPASS Mode. Power output: 1-80.0W.
Temperature control mode:100℃-315℃/ 200℉-600℉,
TCR settings. Support USB 2A charging. PC firmware
upgradeable.
Please refer to the ofcial website of Hot
Technology
about the TCR settings and upgrades
User Manual
2
PRODUCT DETAILS:
①
②
③
④
⑤
①510 connector
②FIRE
③OLED screen
④“+/-”Button
⑤USB port
3
ON/OFF:
CONNECT THE ATOMIZER:
After loading the battery, it will display
“"HOTCIG, POWERED BY HM”, and then it
enters the main interface. Press the FIRE button
five times to display SYSTEM OFF, then it shuts
down; press the FIRE button five times to turn it
on again.
ON:
OFF:
The screen displayed after the atomizer is connected,
Press the “+” “-” button to switch between new or former atomizer.
The screen will Show “CHECK ATOMIZR” when the atomizer is
unconnected; It will show SHORTED when there happened Short
circuit; it will show OHMS TOO HIGH when the resistance is too
high; it will show OHMS TOO LOW when the resistance is too low.
4
OUTPUT MODE:
Filled the bottles, then install the battery, squeeze the squonk
bottle, e-liquid can be directly injected into the BF atomizer.
Pressing the FIRE button three times until one of the display
ashes, and then press again FIRE button (1-3 times) to switch to
the Output Mode, and nally press the +/- button to switch among 3
output modes: POWER Mode, BYPASS Mode, TC Mode.
Rell e-liquid:
(A)
(%) (P)
(S)
5
1. POWER Mode :
A.Wattage adjustment: You can adjust to the appropriate wattage
(1-80W) according to your needs by pressing the +/- button in
POWER mode.
B. Function adjustment: in POWER mode, Press the +/- button
to lock or unlock the resistance value after the FIRE button is clicked
3 times in succession and the screen resistance value ashes,
in the state where the resistance value is ashing, Press the FIRE
button to switch to the main parameter display item, then Press the
+/- button to select the display of output current (A), the output time
(S), the battery charge (%), and the number of outputs (P).
2.BYPASS Mode:
When pressing the FIRE button three times to switch to the main
parameter display Item in BYPASS mode. Press the +/- button to
select the output current (A), output time (S), battery power (%) and
output times (P) (refer to the above).
FIRE
①
②
6
3.TC Mode:
A.Temperature adjustment: Press +/- to adjust the temperature
(° C / ° F) High and low In TEMP mode.
B. Resistance ne-tuning: Press 3 times FIRE button while the
resistance value hints ash. The rst click of the +/- button switch
to the resistance ne-tuning interface. Press the +/- button to ne-
tune the resistance value, ne-tuning range between -0.09 to +0.09.
In the TC mode, ne-tune function remain OFF. The system will
automatically keep your modied resistance.
C. Power adjustment: in TC Mode, after you fix the ohm
resistance adjustment. Press the FIRE button to switch to the power
value interface and while the power value flashing, press the +/-
button to adjust wattage range.
D. Heat material selection: After the power adjustment, press
FIRE button to switch to material items. While the material item
ashes, press the +/- button to switch NI, TI, SS,TCR material.
7
TCR EXTENT:
BUTTON SET:
Material TCR value PPM/℃
Nickel 4952-7428
Titanium 3296-4944
SS（303,304,316）704-1056
TCR（XX）704-8000
A. Lock/ unlock: When hold the “+”button and “-”button for 3
seconds at same time the product will show “ key locked ”, the “+/-”
will be locked. Only press re and “+/-” can get interactive reaction.
Press the “+” button and “-”button for 3 seconds at same time the
product will show “key unlocked”, the“+/-” will be unlocked. As
below picture:
B.Flipping screen: When the product is locked, press the
FIRE button and the "-" button the screen will flip to the
opposite direction. As below:
+
-
+
-
8
Connect to USB:
ALARM NOTICE:
This device could be charged via USB wall charger or connected
to computer’s USB port. When connecting to the computer, it performs
“charge mode" by default, press “+/-" button to choose“update” or
“charge”, and press the FIRE button to confirm. While charging, the
battery logo keeps flashing, the logo will disappear when battery gets
fully charged.
C. RGB Settings: while "+" "-" button locked, hold FIRE and "+"
button at the same time,color table will display on screen, click "+""-"
to choose color, and press FIRE button to confirm.
Table of contents
