Hongda USA Shepherd 240 User manual
http:// www.cchongda.com.cn
1
黑贝 240B V0.02
Preface
Thank you for using Shepherd 240 Biometric Fingerprint Lock
Please read this Installation Manual carefully before attempting
to install your new lock. This manual covers installation
procedures
Manufacture or their representative, will not be responsible for
any damages caused by incorrect installation or mishandling of
the lock. Any such damages will void manufacture’s warranty.
http:// www.cchongda.com.cn
2
黑贝 240B V0.02
Table of Contents
Preface……………………………………………….………………………..1
Table of Contents…………………………………….…………………….…2
1. Identifications…………………………………….………………….…….3
2. Required tools……..………………………………………………………4
3. Pre installation
3.1 Locating hole center from the edge of the door……….……………5
3.2 Deadbolt adjustment..…………………………………………………6
4. Installation
4.1 Deadbolt installation……….………………………………….……….7
4.2 Installation of Deadbolt Strike and Strike Lining Box……………...8
4.3 Sizing torque bar……………..…………………………….………..9
4.4 Installation of the outside Lock……..……………………………..10
4.5 Installation of Inside Lock………… ………………………………...11
4.6 Tightening Screws……………………………………………………12
4.7 Final Inspection / adjustment prior to saving fingerprints…..........13
http:// www.cchongda.com.cn
3
黑贝 240B V0.02
1. Identifications
Please familiarize yourself with all the parts. If any part is missing or
damaged, contact our service center or manufacture immediately.
Inside Lock Assembly
Outside Lock Assembly
Outside Rubber Seal
Inside Rubber Seal
Deadbolt
Strike Lining Box
Deadbolt Strike
Overriding Keys
Attaching Screws
http:// www.cchongda.com.cn
4
黑贝 240B V0.02
2. Required Tools
1.Electric or battery operated Drill 2.One 3/8” Diameter Drill Bit
3.One 1” Diameter. Drill bit 4. One 2 1/8” Diameter Drill Bit
5. A Carpenter Chisel 6.A Hammer
7.．A pair of scissors 8.A pair of pliers．
Wooden Screws
http:// www.cchongda.com.cn
5
黑贝 240B V0.02
Measure this
distance
(needed for
deadbolt
adjustment 2
3/8”or 2 3/4”)
3. Pre installation
3.1 Locating hole center from the edge of the door
Existing door with deadbolt Existing Door without deadbolt
Door with existing cylindrical deadbolt lock: Remove existing cylindrical
deadbolt and install the new Shepherd 240 in its place per Section 4 and
paper template
Door that does not have a cylindrical deadbolt lock nor a hole for the
cylindrical deadbolt lock: Mark the center of the new hole by measuring
the distance from the edge of the door to the existing latch lock center;
door with one hole measure the distance from the edge of the door to
the center of the hole. It should measure either 2 3/8” or 2 3/4”
(American door lock standard). This distance dictates the length of the
deadbolt see section 3.2.
Latch Lock
Shepherd
240 replaces
cylindrical
deadbolt lock
Latch Lock
5 1/2”
http:// www.cchongda.com.cn
6
黑贝 240B V0.02
3.2 Deadbolt adjustment
①Manufacture setting is 2 3/8” shown
on deadbolt
②If 2 3/4” is needed, turn and pull
as shown
③Make sure it clicks and the number
matches the measurement you
obtained from section 3.1.
Turn
Pull
http:// www.cchongda.com.cn
7
黑贝 240B V0.02
4. Installation
4.1 Deadbolt installation
①Insert the deadbolt from the side
of the door (follow the “UP”sign).
Mark the edges. Then carve out 1/8”
deep rectangular shape, per your
marking, using chisel and hammer.
②Insert the deadbolt make sure
the deadbolt (“UP”sign), is up.
Then screw it to the door.
http:// www.cchongda.com.cn
8
黑贝 240B V0.02
4.2 Installation of Deadbolt Strike (on the door) and Strike Lining
Box (on the door frame).
Install Deadbolt Strike Lining Box by
aligning the dead bolt on door with
the frame. Make a deep enough
cutout with chisel and hammer, to
accept the Strike Lining Box.
Install the Strike Lining Box and
screw it to the frame using provided
wooden screws.
http:// www.cchongda.com.cn
9
黑贝 240B V0.02
4.3 Sizing torque bar (to the right length)
Shepherd 240 is designed to fit door thickness of: 1 7/16” to 2”.
Trim the torque bar accordingly with a pair of pliers.
(Sketch is not to scale)
(Door thickness 1 7/16”- 2”)
TRIM TORQUE BAR PER DOOR THICKNESS
Use full length if door thickness is 2”
Trim here if door thickness is 1 3/4”
Trim here if door thickness is 1 7/16”
Trim here if door thickness is 1 1/2”
Trim here if door thickness is1 7/8”
http:// www.cchongda.com.cn
10
黑贝 240B V0.02
4.4 Installation of the outside Lock (which contains the finger
scanner)
Table of contents
Other Hongda USA Lock manuals
