Honeywell HBT083P User manual

CSHBT083PV1 12/04 Rev.A

HBT083P/MDT083P

HBT083P/MDT083PHBT083P/MDT083P

HBT083P/MDT083P

KSU/PBX Telephone

KSU/PBX TelephoneKSU/PBX Telephone

KSU/PBX Telephone

Distribution Hub/Module

Distribution Hub/ModuleDistribution Hub/Module

Distribution Hub/Module

INSTALLATION GUIDE

Description

The HBT083P and MDT083P Hub and Module provide distribution of four (4) incoming telephone lines to eight

(8) locations via 110 connectors, and One (1) video signal to eight (8) locations. The Hub/Module also includes

a 12dB amplifier and two (2) coax pass through connections for Satellite TV. This Module will requires 6-inches

of space in a QuickNetwork rough-in can.

Features

• Twelve ports

• Four line capability

• RJ31x port

• Labeling space for every port

Important Warnings

♦ Never install or work with telephone wiring during a lightning storm.

♦ Never install telephone jacks in wet locations unless the jack is specifically designed for use in wet locations.

♦ Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at

the network interface.

♦ Use caution when installing or modifying telephone lines.

♦ Have the Electrician connect the AC outlet to branch circuit power. The connection should be in accordance

with the National Electrical Code, Articles 110, 250 and 300.

Installing the Distribution Hub/Module

Connect the service input cable to the center F-type

coax port on the module labeled “CATV/ANT IN”. These

signals can be either Cable TV, Antenna or a modulated

video signal. Connect a coax cable between the “12 V

DC IN” port and the provided DC power module. Once

the input and power cables have been connected the

video signal will be distributed the video signal to all of

the outputs on the module. There are also two Pass

through Aux. ports that can be use to pass satellite

signals.

Connecting TV outlets to outputs

1. Remove the silver terminating caps ONLY from the

ports that will be connected to outlet cables.

Keeping the caps on unused port, will help prevent

unwanted video signals from entering your TV

system.

2. Connect the outlet cables to the module.

3. Connect the incoming cables from the Satellite TV to

the pass-through F connectors on the rear of the

module.

4. Connect the outgoing satellite cables between the

receiver and the front side of the module.

Connecting Telephone Service

Connecting Incoming Phone Lines

1. Trim back the PVC jacket on the incoming phone

cable approximately ¾-inch (be sure to re-label if

necessary) allowing for a bend radius of at least

four times the diameter of the CAT5 telephone

cable.

2. Separate the pairs from each other but do not

untwist the pairs. Be sure to label each

connection on the provided documentation

template painted on the face of the module.

Note: Do not untwist the conductors more than ½-inch from

the point of termination.

3. Following the 568A color code that is printed on

the 110 connectors, punch down the incoming

cables on the module’s 110 connectors. Start with

the blue pair punch the cable down into the slots.

4. Punch down all the Cat5e cables in the same

fashion, positioning and trimming each in order to

maintain neatness.

Note: Make sure that the Tip and Ring are properly

connected to the 110 punch down. In most cases the

blue/white is first and then the white/blue.

5. Once the remaining cables have been connected

(up to four lines) the incoming phone lines will be

distributed to the outlet ports on the top side of

the module.

Connecting outgoing telephone cables

The outgoing RJ45 ports will accept cables with either

RJ45 or RJ11 connectors. RJ45 termination is

recommended so that the four line capability can be

used. When terminating the cables follow the 568A

standard.

If a MDP3 patch module is being installed, connect a

patch cord between the telephone outputs and the

zones on the MDP3 patch module.

Connecting the module to a Security System

After phone service has been connected to the

module, route a CAT5 patch cord between the RJ31x

port and the security system. Cut the RJ45 connector

off at the Security system end and use the following

diagram to connect the phone service to the security

system and to the module.

‡CSHBT083PV1aŠ

CSHBT083PV1 12/04 Rev. A

This manual suits for next models

Table of contents

Other Honeywell Switch manuals

Honeywell

Honeywell 39346 User manual

Honeywell

Honeywell 88173 User manual

Honeywell

Honeywell DG T Series User manual

Honeywell

Honeywell MDDS8202 User manual

Honeywell

Honeywell EVN2000 Series Installation instructions

Honeywell

Honeywell PLS531A User manual

Honeywell

Honeywell GSS Series User manual

Honeywell

Honeywell CENTRAL HUB User manual

Honeywell

Honeywell C6097 User manual

Honeywell

Honeywell PLS530A User manual

Honeywell

Honeywell ZW4003 User manual

Honeywell

Honeywell Fema DCM-203-574 Series User manual

Honeywell

Honeywell 43191680-001 User manual

Honeywell

Honeywell 272630D User manual

Honeywell

Honeywell MAXPRO-Net Assembly instructions

Honeywell

Honeywell Limitless WGLA Series User manual

Honeywell

Honeywell CSS-O-A300-001 User manual

Honeywell

Honeywell VC Series User manual

Honeywell

Honeywell DPS 200 Instruction manual

Honeywell

Honeywell nfs2-3030 User manual

Honeywell

Honeywell DPSL200 User manual

Honeywell

Honeywell MICRO SWITCH GSX User manual

Honeywell

Honeywell DG-T Series User manual

Honeywell

Honeywell Fema DWAM Series User manual

Popular Switch manuals by other brands

URC

URC Total Control MFS-8 installation manual

Azbil

Azbil HPQ-D11 user manual

Sony

Sony DFS-900M operating instructions

SICK

SICK i17S operating instructions

F&F

F&F SZR-277 quick start guide

Shure

Shure UAMS/BK user guide

Dräger

Dräger X-zone Switch Off Instructions for use

Asco

Asco Joucomatic 349 Series manual

BT Mini Hub user guide

D-Link

D-Link DES-1226G manual

Johnson Controls

Johnson Controls FS80-C installation instructions

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Configuration guide

MicroNet

MicroNet SP1200A user manual

Ruijie

Ruijie RG-PF2920 Series Hardware installation and reference guide

Altinex

Altinex DA1914SX user guide

MiLAN

MiLAN MIL-SM2401M user guide

RJM

RJM MASTERMIND PBC/6X user manual

Atlas

Atlas MMK-KVM8 owner's manual