Honeywell 5800PIR-RES User manual
5800PIR-OD Wireless Outdoor Motion Sensor – Installation Instructions
GENERAL INFORMATION
The Honeywell 5800PIR-OD Wireless Outdoor Motion Sensor
(referred to as the 5800PIR-OD) combines the convenience of
wireless technology with a full featured outdoor PIR motion
sensor. The major features are highlighted below:
Immunity to bright light
disturbances from headlights,
sunlight, and other bright
light sources.
Selectable detector
range and angle.
Discriminates both large and
small animals to reduce false
alarms.
Tamper detection.
Battery saving circuit
allows for a 5 or 120
second period of
inactivity before being
reactivated.
SPECIFICATIONS
Detection Method Passive Infrared
Initial Warm Up ~ 2 minutes
Dimensions Height 199mm (7.8 in.)
Width 82mm (3.2 in.)
Depth 120mm (4.7 in.)
Mounting Height 0.8 - 1.2m (2.7 - 4ft) To the center of
lens.
Range Adjustable up to 12m (40ft)
Pattern 90°pattern consisting of 13 zones. This
pattern can be adjusted in 15°incre-
ments from center up to 45°.
Sensitivity 2.0°C at 0.6m/s (3.6°F at 2.0ft/s)
Detection Speed 0.3 - 1.5m/s (1 - 5ft/s)
Operating Voltage 6 VDC (uses 4 lithium 1.5VDC AA cells)
Battery Saving Timer Adjustable 120sec or 5sec
Alarm Period ~ 2.5 seconds
LED Indicator Enabled during a walk test.
Disabled for normal operation.
Weatherproof IP54 compliance
Operating Temperature – 20 to + 50 °C (– 4 to +122°F)
Humidity 95% Max
Accessories (included) Pole mounting kit, screw kit, detection
masking strips.
INSTALLATION (refer to the Component Identification Diagram on page 7)
1 Select the Mounting Position
Avoid strong sunlight into the sensor's field.
Avoid moving or swaying trees and bushes.
Orient the detector
so that intrusion
passes across the
detection field, not
into the sensor.
Allow 110mm (4.4")
above the sensor to
enable opening the cover.
Choose an installation
height of 0.8m to 1.2m
(2.7 to 4ft).
Ensure the sensor can be
mounted on a perpendicular
wall or pole that would make
its detection pattern parallel
to the ground.
Parallel
2 Prepare the Sensor for Mounting
1. Remove the Cover by pulling from bottom.
2. Remove Detector from the Back Box by pulling from top.
– 2 –
3 Install / Replace the Battery
IMPORTANT:
Use only lithium batteries.
Use four (4) lithium 1.5VDC AA cells. (Energizer L91 or
equivalent.)
Change all four batteries at the same time. Do not mix
weak batteries with new batteries.
Observe polarity.
1. If necessary, loosen the Captive
Lock Screw and lift Cover off.
Then, remove 4 screws that secure
the Detector to the Back Box.
2. Observe the proper polarity and
replace the batteries. Ensure
positive side of battery is pointing
away from the springs.
4 Mount the Sensor
WALL MOUNTING
1. Install the Back Box on the wall
using two M4 x 20 mounting
screws.
UP
2. Secure the Detector to the Back
Box.
3. Fasten with four self tapping
M3 x 14 screws.
4. Perform Settings & Adjustments.
5. Perform a Walk Test.
6. Secure the Cover with the M3 x 10 Captive Lock Screw.
7. Program the control panel.
POLE MOUNTING
1. Use a pole with an outside
diameter of 43-48mm
(1.69-1.89").
2.7- 4ft.
0.8 - 1.2m
2. Attach the Brackets to the Back
Box with two M3 x 8 screws.
3. Using the Pole Brackets
and four M4 x 30 screws,
fasten the Back Box to the
pole.
UP
4. Secure the Detector to
the Back Box and
fasten with four self-
tapping M3 x 14 screws.
5. Perform Settings &
Adjustments.
6. Perform a Walk Test.
7. Secure the Cover with
the M3 x 10 Captive
Lock Screw.
8. Program the control
panel.
You may have to move
aside the sponge packing
to reveal the screw holes.
– 3 –
5 Perform Settings & Adjustments
SET THE DETECTION LENGTH
Note: The length of the lower detection area determines the detection length.
The upper detection area stays parallel to the ground at all times. The lower detection area can be adjusted by the Detection Length
Adjustment Switch as shown below.
Detection length is therefore limited by the length of the lower detection area since both upper and lower areas have to be blocked at the same
time to activate the sensor.
IMPORTANT:
This sensor detects temperature differences between the moving object and the background temperature in the detection area to produce a
valid detection.
If the object does not move, the sensor will not detect it.
If there is traffic near the detection area, adjust the detection area length 1.5 to 2.0m (5 to 7ft) back from traffic.
Detection Length
Detection Length
Detection Length
UPPER and LOWER beams are blocked,
detection is made.
Only the LOWER beam is blocked,
detection is not made.
Only the UPPER beam is blocked, detection is not
made.
Press and slide the Detection Length Adjustment Switch to the desired position.
A
B
C
D
DETECTION LENGTH
D 02.0m (6.7ft)
C 05.0m (16.7ft)
B 08.0m (26.7ft)
A 12.0m (40.0ft)
NOTES:
•This table is based on a motion sensor
height of 1m (3.3ft)
•The height of the motion sensor will
effect the detection length. In addition,
the detection length may vary due to
environmental conditions.
SET THE DETECTION AREA ANLGLE
1. The detection area angle is 90°with 7
fingers as shown.
90o
45o
45o
Top view
012
10
5
5
12
12
0
10
10
5
(m)
(m)
45 Adjustable
Active detection
fingers.
o
45 Adjustable
o
2. Hold the sensor and turn it to the desired
direction. Each click represents 15°of change.
Adjust to
desired direction
Default Setting
Position A– maximum of 40 ft.
Position B– maximum of 26 ft.
Position C– maximum of 16 ft.
Position D– maximum of 6 ft.
3.3
ft.
3.3
ft.
3.3
ft.
3.3
ft.
10 20 30 40 feet
10 20 30 40 feet
10 20 30 40 feet
10 20 30 40 feet
– 4 –
IF NECESSARY, CONFIGURE DETECTION MASKING
1. Spread the Cover and gently press on the
Lens to remove the Lens Holder.
2. Separate the Lens from the Cover.
Cover
Lens
Area Masking
Plate
Lens
Holder
3. Identify the segments on the Lens to be masked.
4. Then apply the adhesive Masking
Strip(s), as necessary, inside the
lens to mask the desired
segments.
113
2
3
4
5
678
9
10
12
11
113
2345678910 12
11
5. Replace the Lens by aligning the 4 cutouts
on the lens to the 4 projections inside the
cover. Snap in place with the Lens Holder.
Cover
Lens
6. Ensure the Lens Holder is held by the left and
right cover prongs and the two tabs are engaged.
Cover
Lens
Holder
SET THE SENSITIVITY SET THE DIP SWITCHES
1. Set the Sensitivity Select Switch to the desired
sensitivity.
Sensitivity
Select Switch
(Low, Med, High)
DIP
Switches
Low Sensitivity - Best to prevent false detections.
High sensitivity - Best detection catches (increased
false detections). Use for applications where you are
tagging video, or need high security awareness.
1. At the DIP switches, set switch 2
for the desired Battery Saving
Timer period.
Note: The alarm output
activations are limited by the timer
selection (5 or 120 seconds). Even
if there are continuous alarm
events, the alarm output operates
only once in the selected timer
period. This period can be set for 5
or 120 seconds.
120s – Default Setting
5s – Used when frequent alarm
transmission is required. Battery
life will be shortened when using
this setting.
2. Set switch 3 for the desired Pulse Count
(selectable for 2 or 4).
Pulse Count of 2 = detection can be
made with as little as two steps.
Pulse Count of 4 = detection can be
made with as little as four steps.
3. Set switch 1 to enable the Walk Test,
then perform the walk test on the next
page.
ON 1. Walk Test
5s 2. Battery Saving Timer
23. Pulse Count
ON
123
OFF
120s
4
Default Setting
Default Setting
– 5 –
6 Perform a Walk Test
NOTE: With the Walk Test switch set to ON the LED will light when the detector is tripped, and the alarm is generated instantly.
1. Set the walk test
switch (DIP switch
1) to ON. Replace
the cover.
2. Perform a walk test
through the detec-
tion area, and verify
satisfactory results.
3. Allow the detection
area to remain
static, and check for
false or unwanted
detections.
4. If necessary, adjust
the detection area (see
Perform Settings &
Adjustments).
5. Repeat the walk test
through the detection
area, and verify
satisfactory results.
6. Set the walk test DIP
switch 1 to OFF, and
secure the Cover with
the M3 x 10 Captive
Lock Screw.
Notes:
If normal car or people traffic
pass close to the detection
area, adjust the detection
area 1.5 to 2.0m (5 to 7ft)
shorter to reduce false
detections. This also allows
for changes due to environ-
mental thermal conditions.
If the detection length is
adjusted to position "A" [12m
(40ft)], the detection area
may increase when there is a
big temperature difference
between the moving object
and the background.
If this causes a problem, adjust the detection
length to position "B". Then walk test to verify
satisfactory results.
Approx.8m (27ft)
position B
Approx.12m (40ft)
WALK TEST
This sensor has a multi-level
detection pattern (from side
view). A heat source beyond
the detection area may cause
the detector to issue a false
alarm by reflecting off the
ground. Examples include
puddles, wet surfaces, very
smooth asphalt or concrete
surfaces.
If this causes a problem,
adjust the detection length to
position "B". Then perform a
walk test to verify
satisfactory results.
7 Program the Control Panel
Prior to use in the system, you must program the transmitter's serial number, input type (RF Supervised), response type, and loop # (set to 1)
in the control panel. Refer to the control panel’s instructions for further details.
Note: If you are learning the control panel by walking, either use the Walk Test setting or temporally set the Battery Saving Timer to 5 sec.
When the programming is complete ensure the Walk Test switch is set to OFF, and the Battery Saving Timer is set to your desired setting.
– 6 –
TROUBLESHOOTING
SYMPTOM CAUSE REMEDY
Batteries are incorrectly installed or
dead.
Check for correct battery installation, or replace dead batteries.No detection, when walking
through the detection area.
Wiring is faulty or loose. Check all connectors and wiring.
Water in unit. Check for cracks in the housing that would allow water infiltration.
Replace unit.
Transmitter or PIR sensor is faulty. Replace unit.
No detection occasionally, or
poor detection.
Sensitivity is set too low. Try a higher sensitivity setting.
Detection area is not set correctly. Perform a Settings & Adjustments procedure.
Low battery fault indicated
on system keypad display.
Batteries are very low or dead. Replace batteries.
Alarms when no one is
walking through the
detection area.
Sensor is not perpendicular to
ground.
Remount and align sensor so the detection area is parallel to the
ground.
Sensor is detecting moving trees,
bushes, or a strong source of light.
Check for moving trees, or bushes or a strong light source. Perform a
Settings & Adjustments procedure.
Lower detection area is too long. Set Detection Length to a shorter range.
A heat source in the area may be
causing an abrupt temperature
change.
Move or remove the heat source.
Mask the area pointing to the source of heat, or shorten the Detection
Length.
– 7 –
COMPONENT IDENTIFICATION DIAGRAM
Transmitter
Sensor
(Do not touch)
Cover
LED
Indicator
Cover
Lens
Back Box
Use four M4x30 screws if
mounting to pole brackets,
or two M4x20 screws
if mounting to wall.
Captive
Lock Screw
M3 x 10
Masking Strip
(Use as required)
Lens
Holder
UP
DIP Switch
Sensitivity Select
Switch Detection Length
Ajustment Switch
Pole
Bracket
FCC / IC STATEMENT
This device complies with Part 15 of the FCC Rules, and RSS210 of IC.
Operation is subject to the following conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause
undesired operation.
INFORMATION TO USER
Unauthorized changes or modifications could void the user's authority to operate the equipment.
DOCUMENTATION AND ONLINE SUPPORT
For the latest documentation and online support information, please go to:
http://www.security.honeywell.com/hsc/resources/MyWebTech/
WARRANTY
For the latest warranty information, please go to:
http://www.security.honeywell.com/hsc/resources/wa/
2 Corporate Center Drive, Suite 100
P.O. Box 9040
Melville, NY 11747
Copyright ©2009 Honeywell International Inc.
www.honeywell.com/security
ÊK15009V2>Š
K15009V2 2/10 Rev. A
This manual suits for next models
1
Table of contents
Other Honeywell Security Sensor manuals
Honeywell
Honeywell Miller Titan TR50 User manual
Honeywell
Honeywell SS2 Series User manual
Honeywell
Honeywell IQ Force Installation manual
Honeywell
Honeywell Viewguard PIR AM FAI Instruction manual
Honeywell
Honeywell HAQSPA User manual
Honeywell
Honeywell Small SATCOM Instruction Manual
Honeywell
Honeywell Series 3000 MkII User manual
Honeywell
Honeywell MILLER 1032363 User manual
Honeywell
Honeywell Lyric User manual
Honeywell
Honeywell AreaRAE Plus User manual
Honeywell
Honeywell PROINDMV Assembly instructions
Honeywell
Honeywell ADEMCO 5821 User manual
Honeywell
Honeywell C7024E User manual
Honeywell
Honeywell RAEGuard 2 PID User manual
Honeywell
Honeywell IS216 Installation and operation manual
Honeywell
Honeywell Ex-Or MLS Series Quick start guide
Honeywell
Honeywell IRPI8EZS User manual
Honeywell
Honeywell Ex-Or MLS2500CDR Installation and operation manual
Honeywell
Honeywell Ex-Or MR1500P Installation and operation manual
Honeywell
Honeywell NFPA 1971 Owner's manual
