Honeywell SeqLED E SET-30 User manual
GB
SeqLED E
70mm
160mm
160mm
70mm
26mm
26mm
Dimensional Drawings:
Honeywell Life Safety AS, Po. Box 3514, N-3007 Drammen, Norway http://www.hls-nordic.com
Installation:
Step 2: Unfasten the four retaining screws without removing them and remove the diffusor.
Step 3: Set the module address. For more information about module settings see the next
page.
Step 1: Unfasten the front screw and remove the cover.
2
13
Weight:
Technical description
Part no.:
Lumen output:
o
-30 to 60 C
Up to 95%
Produced in accordance with:
Ambient Temperature Range:
Maximum Power Consumption:
Operation Voltage: 220-240V AC/DC, 50-60 Hz
280 lm
500 gr
3.8W / 4.2VA
138005.S30
SeqLED E SET-30 230V
Relative Humidity:
Technical lifetime (light source): > 100000 hours
IP65
Degress of cover protection:
EN 60598-1, EN 60598-2-22, EN 55015
EN 61547, EN 61000-3-2, EN 61000-3-3
GB
Honeywell Life Safety AS, Po. Box 3514, N-3007 Drammen, Norway http://www.hls-nordic.com
PE N L
PE N L
washer
rubber
o-ring
PE N L
PE N L
MOUNTING METHODS
Surface mounting on the wall
3
6
2
5
1
4
INSTALLATION
Step 1: Unfasten the front screw and remove the cover. Next, unfasten the four retaining screws without
removing them and remove the diffusor.
Step 3: Use a drill with a 3,5mm bit to open the 4 mounting holes located in the plastic base. Place the
luminaire on the desired mounting location and mark and drill these 4 holes. Fit the supplied 4
plastic mounting plugs to these drilled holes on the mounting location.
Step 2: Install the supplied cable gasket from the inside of the plastic base.
Step 4: Open a cable entry cutout hole on the plastic base and install the supplied cable gasket. Make a
hole in the center into the desired gasket by using a small screwdriver and pass the round cable
through the gasket. Connect the main cables to the respective terminal block: N for neutral, L for
live wire and PE for ground wire. Install the included tie (if needed) to fasten securely the power
cables. Always use in any case round mains cable, with a diameter of 5-10mm (H05RN-F type
2x1mm² or any other type, at least equal to it's mechanical and electrical properties). ATTENTION!!
The cable must not be deformed in any way (This requirement is important to ensure the IP rating).
Step 6: Re-install the diffusor, fasten the four retaining screws, refit the cover and fasten the screw that
was removed in step 1.
Step 5: Mount the base to the desired location by using the supplied screws, washers and o-rings in
each mounting hole.
At the end of their useful life the packaging and product
should be disposed of via a suitable recycling centre.
Do not dispose of with your normal household waste.
Do not burn.
The light source contained in this luminary shall only be replaced by the manufacturer, or his
agent, or a similar qualified person.
NOTE! The light source is non-user replaceable.
GB
Honeywell Life Safety AS, Po. Box 3514, N-3007 Drammen, Norway http://www.hls-nordic.com
MODULE FOR SINGLE LAMP SELECTION AND MONITORING
Switching of one selected light in the electric circuit
SET010 select
DIP-switch 1
ON for non-maintained mode (Default)
DIP-switch 2
OFF for lighting address 1-16 (Default)
ON for lighting address 17-32
Indicator LED
Rotary coding switch
for setting the exact lamp adress DIP-switch 3 (OFF)
Attention!
Connect L and N correctly!
Exchanging L and N causes malfunction.
Setting the lighting address is carried out by a rotary coding switch that is easily accessible from the
outside.
The module is already prepared for administering a total of 32 lighting addresses.
Function
By means of a suitable control, it is possible with the aid of the SET010 select to determine whether the
lamp connected to it is ready for use or faulty.
Lighting addresses 1 to 16 can be slected when DIP switch 2 is set at OFF.
The address range 17 to 32 can be selected by setting DIP switch 2 to ON.
Settings
(DIP switch 2 = ON and rotary coding switch = 1 is equivalent to lighting address 17 etc.)
Technical description
Cross section:
Temperature:
Dimensions (L x W x H in mm) 78 x 30 x 20
2
Max: 1.5mm
-30°C up to +60°C, T =+75°C
cmax
SET010 select
Prewired
This manual suits for next models
1
Other Honeywell Relay manuals
Honeywell
Honeywell Silent Knight WSK-RELAY User manual
Honeywell
Honeywell Aquastat L8124B Operation manual
Honeywell
Honeywell HPSR103 User manual
Honeywell
Honeywell TRADELINE R8184G User manual
Honeywell
Honeywell ADEMCO 5800RL Assembly instructions
Honeywell
Honeywell 301RW User manual
Honeywell
Honeywell Aquastat L8148A Operation manual
Honeywell
Honeywell 7800 SERIES User manual
Honeywell
Honeywell NOTIFIER FRM-1 User manual
Honeywell
Honeywell SILENT KNIGHT IDP-Relay User manual
Honeywell
Honeywell AQUASTAT L8124A User manual
Honeywell
Honeywell 7800 SERIES User manual
Honeywell
Honeywell 7800 SERIES User manual
Honeywell
Honeywell 7800 SERIES User manual
Honeywell
Honeywell RA889A User manual
Honeywell
Honeywell 7800 SERIES RM7895A Operation manual
Honeywell
Honeywell 7800 SERIES User manual
Honeywell
Honeywell NOTIFIER FW-RM User manual
Honeywell
Honeywell Farenhyt Series User manual
Honeywell
Honeywell Aquastat L8148A User manual
