Hitachi C 10RD Operator's manual
– 1 –
English
Model
Модель
Jobsite Table Saw
Настольная дисковая пила
C 10RD
Hitachi Koki
INSTRUCTION MANUAL AND SAFETY INSTRUCTIONS
Improper and unsafe use of this power tool can result in death or serious bodily injury!
This manual contains important information about product safety. Please read and understand this manual
before operating the power tool. Please keep this manual available for others before they use the power
tool.
WARNING
ИНСТРУКЦИЯ ПО ЭКСПЛУАТАЦИИ И ТЕХНИКЕ БЕЗОПАСНОСТИ
Ненадлежащее использование данного механизированного инструмента и несоблюдение техники безопасности могут
привести к серьезным травмам!
В данной инструкции содержится важная информация относительно техники безопасности. Перед эксплуатацией
инструмента следует прочесть и полностью понять данную инструкцию. Обеспечьте свободный доступ к данной
инструкции всем, кто будет использовать инструмент.
AЯ46
– 2 –
English
CONTENTS
SECTION PAGE
Product Specifications ................................................................................................................ 3
Power Tool Safety ...................................................................................................................... 4
Table Saw Safety ........................................................................................................................ 5
Electrical Requirements and Safety ........................................................................................... 6
Accessories and Attachments .................................................................................................... 7
Tools Needed for Assembly ....................................................................................................... 7
Carton Contents ......................................................................................................................... 7
Know Your Table Saw ................................................................................................................ 9
Assembly and Adjustments ........................................................................................................ 10
Operation .................................................................................................................................... 15
Maintenance ............................................................................................................................... 18
Troubleshooting Guide ............................................................................................................... 19
Push Stick Pattern ...................................................................................................................... 20
Parts List ..................................................................................................................................... 39
English
СОДЕРЖАНИЕ
РАЗДЕЛ СТР.
Спецификации инструмента......................................................................................................... 21
Техника безопасности механизма................................................................................................. 22
Техника безопасности станка........................................................................................................ 23
Требования к электрике и техника безопасности........................................................................... 24
Аксессуары и дополнительное оборудование................................................................................ 25
Инструменты, необходимые для сборки........................................................................................ 25
Содержимое коробки.................................................................................................................... 25
Знайте конструкцию станка........................................................................................................... 27
Сборка и настройка...................................................................................................................... 28
Эксплуатация............................................................................................................................... 33
Обслуживание.............................................................................................................................. 36
Устранение неполадок.................................................................................................................. 37
Шаблон толкателя........................................................................................................................ 38
Перечень деталей........................................................................................................................ 39
Russian
– 3 –
English
To avoid electrical hazards, fire hazards or damage to the table saw, use proper circuit protection.
This table saw is wired at the factory for 230 Volt operation. It must be connected to a 230 Volt / 6.5 Ampere
time delay fuse or circuit breaker. To avoid shock or fire, replace power cord immediately if it is worn, cut or
damaged in any way. Before using your table saw, it is critical that you read and understand these safety rules.
Failure to follow these rules could result in serious injury to you or damage to the table saw.
WARNING
Some dust created by power sanding, sawing, grinding, drilling and other construction activities contains
chemicals known to the state of California to cause cancer, birth defects or other reproductive harm. Some
examples of these chemicals are:
• Lead based paints
• Crystalline silica from bricks, cement and other masonry products
• Arsenic and chromium from chemically treated lumber
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your
exposure to these chemicals, work in a well-ventilated area and work with approved safety equipment, such as
dust masks that are specially designed to filter out microscopic particles.
PRODUCT SPECIFICATIONS
MOTOR SAW
Type ........................................ Universal Table Size with Extension................. 970mm x 890mm
Amps ....................................... 6.5A Table Extension ................................ Left, Right, Rear
Voltage .................................... 230V/50Hz Rip Capacity with Extension.............. 130mm R x 185mm L
Watts ....................................... 1600W (S6, 25%,10min) Blade Size......................................... 250mm
No load speed ......................... 4800min-1 Rip Scale .......................................... YES
Overload Protection ................ YES Rip Fence ......................................... YES
Mitre Gauge ...................................... YES
Maximum Cut Depth @ 90º .............. 73mm
Maximum Cut Depth @ 45º .............. 63mm
Net Weight ........................................ 21.65kg
WARNING
WARNING
Through poor conditions of the electrical MAINS, shortly voltage drops can appear when starting the
EQUIPMENT. This can influence other equipment (e.g. blinking of a lamp). If the MAINS-IMPEDANCE Zmax <
0.3 OHM, such disturbances are not expected. (In case of need, you may contact your local supply authority
for further information).
Wear safety goggles
Wear ear protection
Wear a breathing mask
ENVIRONMENTAL PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, hoses and packaging should be
sorted, taken to the local recycling center and disposed of in an environmentally safe way.
V........... Volts A............ amperes
Hz......... hertz W........... watts
min....... minutes ~............ alternating current
h........... hours ........... class II Construction
I............ ON O........... OFF
min-1..... revolutions per minute
SYMBOLS
WARNING
Noise can be a health hazard. When the noise level exceeds 85dB(A), be sure to wear ear protection.
– 4 –
English
POWER TOOL SAFETY
WARNING
Before using your table saw, it is critical that you read and understand these safety rules. Failure to follow
these rules could result in serious injury or damage to the table saw.
Good safety practices are a combination of common
sense, staying alert and understanding how to use your
power tool. To avoid mistakes that could cause serious
injury, do not plug in your power tool until you have read
and understood the following safety rules:
1. READ and become familiar with this entire
Operator’s Manual. LEARN the tool’s applications,
limitations and possible hazards.
2.
Look for this symbol that identifies important
safety precautions. It means BE ALERT! YOUR
SAFETY IS INVOLVED!
3. NEVER OPERATE THIS MACHINE WITHOUT THE
SAFETY GUARD IN PLACE FOR ALL THROUGH
–SAWING OPERATIONS.
4. DO NOT USE IN A DANGEROUS ENVIRONMENT
such as damp or wet locations or in the rain. Keep
work area well lighted.
5. DO NOT use power tools in the presence of
flammable liquids or gases.
6. KEEP WORK AREA CLEAN. Cluttered areas and
benches invite accidents.
7. KEEP CHILDREN AWAY. All visitors should be
kept at a safe distance from the work area.
8. DO NOT FORCE THE TOOL. It will do the job
better and safer if used at the rate for which it was
designed.
9. USE THE RIGHT TOOL. Don’t force the tool or
attachment to do a job for which it is not designed.
10. WEAR PROPER APPAREL. DO NOT wear loose
clothing, gloves, neckties, rings, bracelets or other
jewelry that may get caught in moving parts.
Non-slip footwear is recommended. Wear protective
hair covering to contain long hair.
11. WEAR A FACE MASK OR DUST MASK. Sawing,
cutting and sanding operations produce dust.
12. DISCONNECT TOOLS before servicing and when
changing accessories, such as blades, cutters, etc.
13. REDUCE THE RISK OF UNINTENTIONAL
STARTING. Make sure the switch is in the OFF
position before plugging tool into the power supply.
14. USE ONLY RECOMMENDED ACCESSORIES.
Consult the Operator’s Manual for recommended
accessories. The use of improper accessories may
cause injury to you or damage to the tool.
15. REMOVE ADJUSTING KEYS AND WRENCHES.
Form the habit of checking to see that keys and
adjusting wrenches are removed from the tool
before turning ON.
16. NEVER LEAVE TOOL RUNNING UNATTENDED.
TURN THE POWER OFF. Do not leave the tool
before the blade comes to a complete stop.
17. NEVER STAND ON TOOL. Serious injury could
occur if the tool is tipped or if the cutting tool is
unintentionally contacted.
18. DO NOT OVERREACH. Keep proper footing and
balance at all times.
19. MAINTAIN TOOLS WITH CARE. Keep tools sharp
and clean for most efficient and safest performance.
Follow instructions for lubricating and changing
accessories.
20. CHECK FOR DAMAGED OR LOOSE PARTS.
Check for alignment of moving parts, binding
of moving parts, loose mounting and any other
conditions that may affect its safe operation. A
guard or other part that is loose or damaged should
be properly adjusted, repaired or replaced.
21. MAKE WORKSHOP CHILDPROOF with padlocks,
master switches or by removing starter keys.
22. DO NOT operate the tool if you are under the
influence of any drugs, alcohol or medication that
could impair your ability to use the tool safely.
23. USE A DUST COLLECTION SYSTEM whenever
possible. Dust generated from certain materials can
be hazardous to your health and, in some cases,
a fire hazard. Always operate the power tool in a
well-ventilated area with adequate dust removal.
24. ALWAYS WEAR EYE PROTECTION. Any power
tool can throw debris into your eyes that could
cause permanent eye damage. ALWAYS wear
safety goggles (not glasses) that comply with ANSI
safety standard Z87.1. Everyday glasses have only
impact resistant lenses. They ARE NOT safety
glasses.
NOTE: Glasses or goggles not in compliance with
ANSI Z87.1 could cause serious injury when they
break.
25. DIRECTION OF FEED. Feed work into a blade or
cutter against the direction of rotation of the blade or
cutter only.
WARNING
– 5 –
English
TABLE SAW SAFETY
1. ALWAYS USE SAW BLADE GUARD, splitter
and antikickback pawls for every operation for
which they can be used, including through sawing.
Through sawing operations are those in which the
blade cuts completely through the workpiece when
ripping or crosscutting.
2. ALWAYS HOLD WORK FIRMLY against the mitre
gauge or rip fence.
3. ALWAYS USE a push stick, especially when ripping
narrow stock. Refer to ripping instructions in this
Operator’s Manual where the push stick is covered
in detail. A pattern for making your own push stick is
included on page 20.
4. NEVER PERFORM ANY OPERATION
FREEHAND, which means using only your
hands to support or guide the workpiece.
Always use either the fence or the mitre gauge
to position and guide the work.
WARNING: FREEHAND CUTTING IS THE MAJOR
CAUSE OF KICKBACK AND FINGER/HAND
AMPUTATIONS.
5. NEVER STAND or have any part of your body in
line with the path of the saw blade. Keep your hands
out of the saw blade path.
6. NEVER REACH behind or over the cutting tool for
any reason.
7. REMOVE the rip fence when crosscutting.
8. DO NOT USE a molding head with this saw.
9. FEED WORK INTO THE BLADE against the
direction of rotation only.
10. NEVER use the rip fence as a cut-off gauge when
crosscutting.
11. NEVER ATTEMPT TO FREE A STALLED SAW
BLADE without first turning the saw OFF. Turn
power switch OFF immediately to prevent motor
damage.
12. PROVIDE ADEQUATE SUPPORT to the rear
and the sides of the saw table for long or wide
workpieces.
13. AVOID KICKBACKS (work thrown back towards
you) by keeping the blade sharp, the rip fence
parallel to the saw blade and by keeping the splitter,
anti-kickback pawls and guards in place, aligned
and functioning. Do not release work before passing
it completely beyond the saw blade. Do not rip work
that is twisted, warped or does not have a straight
edge to guide it along the fence.
14. AVOID AWKWARD OPERATIONS and hand
positions where a sudden slip could cause your
hand to move into the saw blade.
15. NEVER USE SOLVENTS to clean plastic parts.
Solvents could possibly dissolve or otherwise
damage the material. Only a soft damp cloth should
be used to clean plastic parts.
16. MOUNT your table saw on a bench or stand
before performing any cutting operations. Refer to
ASSEMBLY AND ADJUSTMENTS on page 10.
17. NEVER CUT METALS or materials that may make
hazardous dust.
18. ALWAYS USE IN A WELL-VENTILATED AREA.
Remove sawdust frequently. Clean out sawdust
from the interior of the saw to prevent a potential
fire hazard. Attach a vacuum to the dust port for
additional sawdust removal.
19. NEVER LEAVE THE SAW RUNNING
UNATTENDED. Do not leave the saw until the blade
comes to a complete stop.
20. For proper operation follow the instructions in this
Operator’s Manual entitled ASSEMBLY AND
ADJUSTMENTS (Page 10). Failure to provide
sawdust fall-through and removal hole will allow
sawdust to build up in the motor area resulting in a
fire hazard and potential motor damage.
– 6 –
English
ELECTRICAL REQUIREMENTS AND SAFETY
CONNECTING TO THE POWER SUPPLY
Check that the power supply and plug used is in accordance with your table saw. Have a look at the rating plate of the
motor or the rating on the table saw. Any changes should always be carried out by a qualified electrician.
This machine must be earthed.
If not properly earthed this machine can cause an electrical shock. Be sure that the power supply outlet is earthed. If
there is any doubt, have it checked by a qualified electrician.
Avoid contact with the terminals on the plug when installing (removing) the plug to (from) the power supply
outlet. Contact will cause a severe electrical shock.
USING AN EXTENSION LEAD
The use of any extension lead will cause some loss of power. To keep this to a minimum and to prevent overheating
and motor burn-out, ask advice from a qualified electrician to determine the minimum wire size of the extension lead.
The extension lead should be equipped with an earthed type plug that fits the power supply outlet at one end, and with
an earthed type socket that fits the plug of this machine at the other end.
WARNING
WARNING
– 7 –
English
UNPACKING AND CHECKING CONTENTS
Separate all parts from packing materials. Check each
part with the illustration on the next page and the “Table
of Loose Parts” to make certain all items are accounted
for before discarding any packing material.
TABLE OF LOOSE PARTS
ACCESSORIES AND ATTACHMENTS
RECOMMENDED ACCESSORIES
Visit your Hardware Department or see the Power
and Hand Tools Catalog to purchase recommended
accessories for this power tool.
WARNING To avoid the risk of personal injury:
• Do not use molding head set with this saw.
• Do not modify this power tool or use accessories
not recommended by Store.
WARNING
TOOLS NEEDED FOR ASSEMBLY
CARTON CONTENTS
ITEM DESCRIPTION QUANTITY
ATable saw assembly 1
B Riving knife assembly 1
C Riving knife hardware bag 1
D Rip fence 1
E Blade 1
F Blade wrench 2
G Push stick 1
H Mitre gauge 1
I Push stick storage 1
J Handwheel 1
K Rear table extension 1
L Rear table extension bracket 2
M Rear table extension support 2
N Rear table extension hardware bag 1
O Auxiliary fence 1
P Auxiliary fence hardware bag 1
Q Table side extension 2
R Left side table extension support 2
S Right side table extension support 2
T Table side extension hardware bag 1
U Screw 4
V Base cover 1
STAND:
W Leg 4
X Bottom support bracket 4
Y Long upper support 2
Z Short upper support 2
AA Stand hardware bag 1
Not Supplied
Medium Screwdriver
#2 Phillips Screwdriver
Straight Edge
Adjustable Wrench
Combination Square
Supplied
Wrench
Wrench
If any part is missing or damaged, do not attempt
to assemble the table saw, plug in the power cord,
or turn the switch ON until the missing or damaged
part is obtained and is installed correctly.
NOTE: To make assembly easier, keep contents of box
together. Apply a coat of automobile wax to the table.
Wipe all parts thoroughly with a clean dry cloth. This will
reduce friction when pushing the workpiece.
WARNING
– 8 –
English
UNPACKING YOUR TABLE SAW
ABCD
EFGHIJ
KLMNOP
QRSTUV
WXYZ
AA
– 9 –
English
KNOW YOUR TABLE SAW
The Front of Table Saw
Rip fence
Mitre gauge
Blade bevel lock knob
Right side table extension
Bevel angle pointer & scale
Blade tilting handwheel
OFF ON
Extension support
Stand assembly
Foot pad
Push stick storage
No-Volt-Release (NVR) switch
Upper blade guard
Left side table extension
Rip fence & Mitre gauge storage
Table Insert
Mounting hole
Rear table extension
The Rear of Table Saw
– 10 –
English
ASSEMBLE BASE COVER TO TABLE SAW (FIG. B)
NOTE:
Your saw is supplied with the base cover
unassembled.
1. Assemble the base cover (1) to the saw base (2) by
using the 4 screws (3) in the loose parts bag supplied .
2. Tighten the 4 screws (3) before mounting the saw on
the stand.
Fig. B
ASSEMBLE TABLE SAW TO STAND (FIG. A & C)
1. Position the saw base on the leg set and match the
holes (1) of the saw base to the holes of the stand.
(Fig. C)
2. Secure the saw base to the leg set using bolts (12),
washers (10) and nuts (11). (Fig. A)
Fig. C
For your own safety, never connect the plug to
power source outlet until all assembly steps are
completed and you have read and understood the
safety and operational instructions.
ESTIMATED ASSEMBLY TIME 25~35 MINUTES
STAND ASSEMBLY (FIG. A)
1. Unpack all parts and group by type and size. Refer to
the parts list for correct quantities.
2. Attach one long upper support (1) to top of leg (2)
using one bolt (3) and nut (4).
NOTE:
● Align detents in stand leg with support brackets to
ensure proper fit.
● Do not tighten bolts until stand is properly
aligned (see step #8 before tightening).
3. Attach other end of long upper support to top of
another leg using one bolt and nut.
4. Attach one bottom support (5) to the higher hole (13)
of the leg using bolt (3) and nut (4). This completes
the front frame section.
5. Assemble rear frame section in exactly the same
manner.
6. Join front and rear frame assemblies using two short
upper supports (6), two bottom supports (7), bolts
and nuts.
NOTE: Place the two bottom supports (7) to the
lower holes (14) of the leg.
7. Insert foot pad (8) into bottom of leg. Repeat for each
leg.
8. Place stand on level surface and adjust so all legs
are contacting the floor and are at similar angles to
the floor, and detents in stand leg align with support
brackets, then tighten all bolts.
NOTE: To avoid rocking, tighten all bolts.
Fig. A
ASSEMBLY AND ADJUSTMENTS
3
3
3
3
1
2
1
WARNING
6
914
3
5
2
78
10
11
12
13
14
Table of contents
Languages:
Other Hitachi Saw manuals
Hitachi
Hitachi C 12LDH Manual
Hitachi
Hitachi FC 6SB User manual
Hitachi
Hitachi C7U User manual
Hitachi
Hitachi C 7SS Manual
Hitachi
Hitachi C 6MFA Manual
Hitachi
Hitachi C 10FCH2 User manual
Hitachi
Hitachi C 12LDH Troubleshooting guide
Hitachi
Hitachi C 6MF Manual
Hitachi
Hitachi C 7YA User manual
Hitachi
Hitachi C 10FCE Manual
Hitachi
Hitachi C 10FCE User manual
Hitachi
Hitachi C 8FC User manual
Hitachi
Hitachi CD 7SA User manual
Hitachi
Hitachi C 10RC Operator's manual
Hitachi
Hitachi C 10FL User manual
Hitachi
Hitachi C 15FB User manual
Hitachi
Hitachi CR 13VBY Manual
Hitachi
Hitachi C8FSE - 8-1/2" Sliding Compound Miter Saw User manual
Hitachi
Hitachi CR 13VC Manual
Hitachi
Hitachi CC 14 Operator's manual
