Hitachi L200 Series Quick start guide

Other manuals for L200 Series

5

This manual suits for next models

1

Table of contents

Other Hitachi Inverter manuals

Hitachi

Hitachi SJ100 Series Installation and operating instructions

Hitachi

Hitachi WJ200 Series Software User manual

Hitachi

Hitachi P1-00044-L User guide

Hitachi

Hitachi L100-M Series Addendum User manual

Hitachi

Hitachi J300U Series Instruction and safety manual

Hitachi

Hitachi SJ100 Series User manual

Hitachi

Hitachi SJ100 Series Owner's manual

Hitachi

Hitachi L300P Series User manual

Hitachi

Hitachi L300P Series Quick start guide

Hitachi

Hitachi SJ700-2 Series User manual

Hitachi

Hitachi SJ700 Series Software User manual

Hitachi

Hitachi SJ700-4000HFU2 User manual

Hitachi

Hitachi SJ2002 Series User manual

Hitachi

Hitachi J100-E2 SERIES User manual

Hitachi

Hitachi WJ200 Series Software User manual

Hitachi

Hitachi WJ200-004MF User manual

Hitachi

Hitachi AN032404-1 Rev. A Installation and operating instructions

Hitachi

Hitachi WJ-0001S User manual

Hitachi

Hitachi SJ100 Series User manual

Hitachi

Hitachi L300P Series User manual

Hitachi

Hitachi L2002 User manual

Hitachi

Hitachi L100 Series User manual

Hitachi

Hitachi P1-00250HFEF User guide

Hitachi

Hitachi SJ2-CO User manual

Popular Inverter manuals by other brands

Fourgroup

Fourgroup Easy use and Programming Handbook

Velleman

Velleman PI300M user manual

Sungrow

Sungrow SG350HX-US user manual

WilTec

WilTec 61897 Operation manual

SMA

SMA SUNNY BOY STORAGE 2.5 Quick reference guide

Simplicity

Simplicity LANDLORD 316 product manual

Santak

Santak SMAX 3000 user manual

ATON

ATON RA.Store-3 user manual

ZIEHL-ABEGG

ZIEHL-ABEGG FXET4AMQ operating instructions

Tektronix

Tektronix CFG250 Operator's manual

Champion

Champion 200989 Operator's manual

Vanner

Vanner 20-500 Series owner's manual

GE

GE GEP user manual

Astrel Group

Astrel Group Power Reducer Installation and instruction manual

MULTIQUIP

MULTIQUIP GDP-5H Operation and parts manual

GoWISE

GoWISE PS1007 user manual

Promate

Promate PM13500D ES Operator's manual

Mastervolt

Mastervolt WHISPER 3.5M3000 RPM user manual

Hitachi America, Ltd.

EN-050202-1

ENGINEERING NOTE

SUBJECT: ANALOG VOLTAGE INPUT CALIBRATION ERROR

AFFECTED

MODELS: L200 and SJ200 – MFG DATE 0501 & BEFORE

Certain models of L200 and SJ200 were inadvertently shipped with the 0 – 10

Volt Analog Input (terminal O – L) span parameter improperly calibrated.

The symptom is easily determined. The inverter will operate properly with a

frequency reference from keypad potentiometer, analog 4 – 20 mA input or F001

setting. However when the frequency reference is set to the O voltage input, the

inverter will act erratically at 0 V input, and may trip on overcurrent. The output

frequency will ramp up linearly from 0 V to approximately 0.2 V input with a

corresponding output frequency of 0 to the maximum (factory default is 60 Hz)

frequency. From input voltages from 0.2 V to 10.0 V, the inverter output will

remain pegged at the maximum frequency.

To correct this problem, first stop the inverter. Then follow these steps:

1. Press FUNC to enter the PROGRAM mode.

2. Using the UP / DN arrow keys, navigate to parameter C091.

3. Press FUNC to view the contents, and press UP arrow key to change the

value to 01

4. Press STR to save the change. This will make the so-called “debug”

parameters accessible.

5. Using UP arrow key, navigate to parameter C121

6. Press FUNC to view contents. It most likely is 6553

PGC - 2/2/05 Page 1 of 2

7. Using the DN arrow key, change the value to 1100.(Note the decimal

point after the number - this is critical!!) As you decrement the parameter

value, you will scroll past 1100 (WITHOUT a decimal point!!) Continue

going down toward zero, and the sequence will start again at 9999.

(WITH decimal point after!) and continue decrementing from there.

8. Continue down until the display reaches 1100.Press STR to save the

value. The display should show C121 again.

9. Navigate with the DN arrow key to C091 and press FUNC again.

10.Change setting from 01 back to 00 with DN arrow key. Press STR

again to save. Display again should read C091

11.Press FUNC TWICE until display reads C---

12.Press UP arrow key until you reach o001

13.Press FUNC, then STR This step re-establishes the output frequency

display as the power-on default display.

The analog voltage input should now operate linearly with a 0 – 10 V input

corresponding to a 0 – 60 Hz output.

PGC - 2/2/05 Page 2 of 2