Hilti SF BT 22-A User manual
1
Printed: 19.10.2016 | Doc-Nr: PUB / 5310861 / 000 / 00
2
3
4
5
Printed: 19.10.2016 | Doc-Nr: PUB / 5310861 / 000 / 00
6
Printed: 19.10.2016 | Doc-Nr: PUB / 5310861 / 000 / 00
Printed: 19.10.2016 | Doc-Nr: PUB / 5310861 / 000 / 00
English 1
1 Information about the documentation
1.1 About this documentation
• Read this documentation before initial operation or use. This is a prerequisite for safe, trouble-free
handling and use of the product.
• Observe the safety instructions and warnings in this documentation and on the product.
• Always keep the operating instructions with the product and make sure that the operating instructions
are with the product when it is given to other persons.
1.2 Explanation of signs used
1.2.1 Warnings
Warnings alert persons to hazards that occur when handling or using the product. The following signal words
are used in combination with a symbol:
DANGER! Draws attention to imminent danger that will lead to serious personal injury or fatality.
WARNING! Draws attention to a potentially dangerous situation that could lead to serious per-
sonal injury or fatality.
CAUTION! Draws attention to a potentially dangerous situation that could lead to slight personal
injury or damage to the equipment or other property.
1.2.2 Symbols
The following symbols are used:
Read the operating instructions before use.
Instructions for use and other useful information
Rated speed under no load
Revolutions per minute
Direct current (DC)
Diameter
1.2.3 Illustrations
The illustrations in these operating instructions are intended to convey a basic understanding and may differ
from the actual version of the product:
These numbers refer to the corresponding illustrations found at the beginning of these operating
instructions.
The numbering in the illustrations reflects the order of the work steps in the illustration and may
deviate from the numbering of work steps in the text.
Item reference numbers are used in the overview illustration. In the product overview section, the
numbers shown in the legend relate to these item reference numbers.
1.3 Product information
Hilti products are designed for professional use and may be operated, serviced and maintained only by
trained, authorized personnel. This personnel must be informed of any particular hazards that may be
encountered. The product and its ancillary equipment may present hazards when used incorrectly by
untrained personnel or when used not as directed.
▶Make a note of the designation and serial number printed on the identification plate in the following table.
▶Always quote this information when you contact a Hilti representative or Hilti Service regarding questions
about the product:
Printed: 19.10.2016 | Doc-Nr: PUB / 5310861 / 000 / 00
2 English
Product information
Drill SF BT 22A
Generation: 01
Serial no.:
2 Safety
2.1 General power tool safety warnings
WARNING
Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in
electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated
(cordless) power tool.
Work area safety
▶Keep work area clean and well lit. Cluttered or dark areas invite accidents.
▶Do not operate power tools in explosive atmospheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
▶Keep children and bystanders away while operating a power tool. Distractions can cause you to lose
control.
Electrical safety
▶Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter
plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of
electric shock.
▶Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
▶Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the
risk of electric shock.
▶Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the
risk of electric shock.
▶When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a
cord suitable for outdoor use reduces the risk of electric shock.
▶If operating a power tool in a damp location is unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of electric shock.
Personal safety
▶Stay alert, watch what you are doing and use common sense when operating a power tool. Do
not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A
moment of inattention while operating power tools may result in serious personal injury.
▶Use personal protective equipment. Always wear eye protection. Protective equipment such as dust
mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce
personal injuries.
▶Prevent unintentional starting. Ensure the switch is in the off‐position before connecting to power
source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on
the switch or energising power tools that have the switch on invites accidents.
▶Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may result in personal injury.
▶Do not overreach. Keep proper footing and balance at all times. This enables better control of the
power tool in unexpected situations.
▶Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
▶If devices are provided for the connection of dust extraction and collection facilities, ensure these
are connected and properly used. Use of dust collection can reduce dust-related hazards.
Power tool use and care
▶Do not force the power tool. Use the correct power tool for your application. The correct power tool will
do the job better and safer at the rate for which it was designed.
Printed: 19.10.2016 | Doc-Nr: PUB / 5310861 / 000 / 00
English 3
▶Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must be repaired.
▶Disconnect the plug from the power source and/or the battery pack from the power tool before
making any adjustments, changing accessories, or storing power tools. Such preventive safety
measures reduce the risk of starting the power tool accidentally.
▶Store idle power tools out of the reach of children and do not allow persons unfamiliar with the
power tool or these instructions to operate the power tool. Power tools are dangerous in the hands
of untrained users.
▶Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and
any other condition that may affect the power tool’s operation. If damaged, have the power tool
repaired before use. Many accidents are caused by poorly maintained power tools.
▶Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
▶Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking
into account the working conditions and the work to be performed. Use of the power tool for
operations different from those intended could result in a hazardous situation.
Battery tool use and care
▶Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type
of battery pack may create a risk of fire when used with another battery pack.
▶Use power tools only with specifically designated battery packs. Use of any other battery packs may
create a risk of injury and fire.
▶When battery pack is not in use, keep it away from other metal objects, like paper clips, coins,
keys, nails, screws or other small metal objects, that can make a connection from one terminal to
another. Shorting the battery terminals together may cause burns or a fire.
▶Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact
accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid
ejected from the battery may cause irritation or burns.
Service
▶Have your power tool serviced by a qualified repair person using only identical replacement parts.
This will ensure that the safety of the power tool is maintained.
2.2 Drill safety warnings
▶Use auxiliary handle(s), if supplied with the tool. Loss of control can cause personal injury.
▶Hold power tool by insulated gripping surfaces, when performing an operation where the cutting
accessory may contact hidden wiring. Cutting accessory contacting a "live" wire may make exposed
metal parts of the power tool "live" and could give the operator an electric shock.
2.3 Additional safety instructions
Personal safety
▶Use the tool only when it is in technically faultless condition.
▶Never tamper with or modify the tool in any way.
▶Always hold the tool with the hand on the grip provided. Keep the grip clean and dry.
▶Avoid touching rotating parts – risk of injury!
▶Wear suitable protective glasses, a hard hat, ear protection, protective gloves and light respiratory
protection while using the power tool.
▶Wear protective gloves also when changing the accessory tool. Touching the accessory tool presents a
risk of injury (cuts or burns).
▶Wear eye protection. Flying fragments present a risk of injury to the body and eyes.
▶Take breaks between working and do physical exercises to improve the blood circulation in your fingers.
Exposure to vibration during long periods of work can lead to disorders of the blood vessels and nervous
system in the fingers, hands and wrists.
▶Use a dust removal system and suitable vacuum cleaner whenever possible. Dust from materials, such
as paint containing lead, some kinds of wood, concrete / masonry / stone containing silica, and minerals
as well as metal, may be injurious to health.
▶Keep the power tool out of reach of children. The power tool is not intended for use by inexperienced
persons who have received no special training.
▶Observe the national health and safety requirements.
Printed: 19.10.2016 | Doc-Nr: PUB / 5310861 / 000 / 00
4 English
Careful handling and use of batteries
▶Do not use the battery as a power source for other unspecified appliances.
▶Observe the special guidelines applicable to the transport, storage and use of lithium-ion batteries.
▶Do not expose batteries to high temperatures, direct sunlight or fire.
▶Do not disassemble, squash or incinerate batteries and do not subject them to temperatures over 80°C
(176°F).
▶Do not attempt to charge or continue to use damaged batteries.
▶If the battery is too hot to touch it may be defective. In this case, place the power tool in a non-flammable
location, well away from flammable materials, where it can be kept under observation and allowed to
cool down. Contact Hilti Service after the battery has cooled down.
3 Description
3.1 Overview of the product 1
@Keyless chuck
;Motor cooling air intake
=Grip
%Switch safety lock
&Control switch (with electronic speed
control)
(Belt hook
)Battery
+Air exit
§Battery release button
/Battery display
3.2 Intended use
The product described is a hand-held cordless drill designed for drilling blind holes in steel using Hilti
TXBT… stepped drill bits which is a prerequisite for driving Hilti XBT threaded studs.
▶Use only Hilti lithiumion batteries of the B 18 / B 22 series with this product.
▶Use only Hilti battery chargers of the C 4/36 series to charge these batteries.
3.3 Switch-on interlock release button 2
The tool is equipped with a switch safety lock that can be used to lock the control switch, thereby preventing
inadvertent starting.
Switch positions
• If the switch safety lock is positioned longitudinally, i.e. in line with the working direction of the drill, the
control switch is locked (the safety lock is active).
• If the switch safety lock is pointing to the left relative to the working direction of the drill, the control
switch is free to operate (the safety lock is deactivated).
3.4 Overload and overheating protection
The power tool is equipped with an electronic system to protect against overloading and overheating. The
power tool switches itself off automatically in the event of overloading or overheating. After releasing the
control switch, the power tool may not restart immediately when the switch is pressed again (while the power
tool is cooling down).
Note
Activation of the automatic cut-out is indicated by all 4 LEDs on the battery display blinking.
3.5 Liion battery display
The charge status of the Li-ion battery and malfunctions of the power tool are indicated by the display on
the Liion battery. The charge status of the Liion battery is displayed after pressing one of the two battery
release buttons.
Status Meaning
4 LEDs light. • Charge status: 75 % to 100 %
3 LEDs light. • Charge status: 50 % to 75 %
2 LEDs light. • Charge status: 25 % to 50 %
1 LED lights. • Charge status: 10 % to 25 %
1 LED blinks, the power tool is ready for use. • Charge status: < 10 %
Printed: 19.10.2016 | Doc-Nr: PUB / 5310861 / 000 / 00
Other manuals for SF BT 22-A
5
Table of contents
Languages:
Other Hilti Drill manuals
Hilti
Hilti DD 130 User manual
Hilti
Hilti TE 50 User manual
Hilti
Hilti SFD 2-A User manual
Hilti
Hilti SFE 2-A12 User manual
Hilti
Hilti UD16 User manual
Hilti
Hilti SFC 22-A User manual
Hilti
Hilti TE 60-AVR User manual
Hilti
Hilti DD 110-W User manual
Hilti
Hilti DD 350-CA User manual
Hilti
Hilti TE 60-A36 User manual
Hilti
Hilti SIW 22T-A 1/2 inch User manual
Hilti
Hilti DD 250-CA User manual
Hilti
Hilti DD 150?U User manual
Hilti
Hilti SF BT 22-A User manual
Hilti
Hilti SF 4-22 User manual
Hilti
Hilti TE 70-D/AVR User manual
Hilti
Hilti DD 200 User manual
Hilti
Hilti SF 10W-A22 User manual
Hilti
Hilti TE 50-AVR User manual
Hilti
Hilti DD 150?U User manual
