HENRY LONDON HERITAGE User manual
Your Henry London watch is designed in England & manufactured to the very highest of standards.
These instructions are provided to ensure your watch gives you excellent service, please read them
carefully & retain them for future reference.
INSTRUCTIONS
HENRY LONDON
PAGE ISSUE WWW.HENRY-LONDON.COM
MINUTEHAND
BUTTONA
NORMALPOSITION
BUTTONB
HOURHAND
HOURHAND
CHRONOGRAPHMINUTEHAND
CHRONOGRAPHSECONDHAND
DATEWINDOW
SECONDHAND
SETTINGTHETIME
. Pull the crown out to position , the second hand will stop.
. Turn the crown clockwise to set hour and minute hands.
. Push the crown back into its normal position. The second hand will then resume.
SETTING THE DATE
. Pull the crown out to position .
. Turn the crown anti-clockwise to set the date.
Note – Do not attempt to set the date by turning the crown counter clockwise as this will affect function. The date changes
between the hours of midnight & .am.
. Aer the date has been set, push the crown back into its normal position.
USING THE CHRONOGRAPH
To start the chronograph press button A. The chronograph hands will start moving. To stop the chronograph press button
A again. The chronograph hands stop to indicate the elapsed time. Press button B to reset the chronograph. All the
chronograph hands will be reset to the ‘0’ position. The chronograph can measure up to 30 minutes and then the chronograph
stops. The chronograph can be restarted by pressing button A. During chronograph operation, button B is inoperable.
CHRONOGRAPHRESET
This procedure should be preformed when the stopwatch second & minute hand does not return to the zero. Pull the
crown out to the 2nd position. Press the button “A” to set the stopwatch second hand forward. Press the button “B” to
set the stopwatch second hand back. The stopwatch minutes hand is synchronised with stop watch second hand.
The stopwatch second hand can be advanced rapidly by continuously pressing button "A" or “B”. Once the hand has been
zeroed, reset the time and return the crown to its normal position. Follow these instructions to reset your chronograph
aer battery replacement.
HERITAGE CHRONOGRAPH WITH DATE
CARE&MAINTENANCE
All watch maintenance, including battery replacement requires specialist tools and expertise so should only be undertaken by
a qualified technician, any repairs not carried out by a qualified technician may cause damage to your watch and invalidate the
guarantee.
If your watch is marked ATM on the caseback, then it is designed to withstand accidental water damage. Limited exposure to
water, such as accidental water splashes will not damage your watch, but it is not suitable for showering, bathing or swimming.
If your watch is not marked ATM, then due to the nature of it’s construction, it is not water resistant. Care should be taken to
avoid exposure to water.
Clean your watch regularly with a so cloth to maintain good condition. Keep your watch dry and away from wet surfaces, do
not use chemical cleaners on your strap and avoid contact with cosmetic products. Visit our website for more information.
Your Henry London watch is guaranteed for two years and in the unlikely event your watch develops a fault please contact the
retailer where your watch was purchased. If you purchased your watch from the Henry London online store, please contact our
helpful customer service team at customerservice@henry-london.com or call + () during our business hours
of Monday - Friday, . - . GMT.
TERMS&CONDITIONS
Your month guarantee does not cover the following: . Replacement batteries. . Damage resulting from accidents, or
mishandling to any part of the watch. . Replacement straps or bracelets (unless due to fault). . Damage to lens. . Water
penetration or damage. . Tarnishing of the watch bracelet or case. Your statutory rights are not affected.
INSTRUCTIONS
HENRY LONDON
PAGE ISSUE WWW.HENRY-LONDON.COM
MESH BRACELET ADJUSTMENT
If your Henry London watch has a mesh bracelet, please follow these instructions to ensure you get a perfect fit. Unlock clamp
plate by using an appropriate tool. Move the entire clasp to adjust length by sliding along the bracelet. Adjust length while
wearing the watch to make sure you get a good fit. Make sure the clasp locates into a molded indent on back of bracelet. Lock
clamp plate in position by pressing it into place using your thumb. Do not use retaining bar to gain leverage as this will cause
damage preventing the clasp to lock.
SLIDINGLADDERBRACELET
CLASPRETAININGBAR
CLAMPPLATE
HERITAGE CHRONOGRAPH WITH DATE
Table of contents
