Hengel Bi-Tronic Control User manual

Hengel Industrie

ZA, Les Berges du Rhins - 42120 PARIGNY - FRANCE

Tél : +33 (0)4 77 23 40 00 - Fax : +33 (0)4 77 23 40 09

Email: [email protected]

Website: www.hengel.com

Notice-EN-BITRONIC-ST-F-1

User instructions

Bi-Tronic Control - Retarder proving

To be conserved by the user

Hengel Industrie

ZA, Les Berges du Rhins - 42120 PARIGNY - FRANCE

Tél : +33 (0)4 77 23 40 00 - Fax : +33 (0)4 77 23 40 09

Email: [email protected]

Website: www.hengel.com

Notice-EN-BITRONIC-ST-F-1

Versions of this document

Index

number Date Nature of evolution Revised by

1 28/03/19 Initial document creation YM / SG

Hengel Industrie

ZA, Les Berges du Rhins - 42120 PARIGNY - FRANCE

Tél : +33 (0)4 77 23 40 00 - Fax : +33 (0)4 77 23 40 09

Email: [email protected]

Website: www.hengel.com

Notice-EN-BITRONIC-ST-F-1

Summary

1 - GENERAL INTRODUCTION .................................................... 4

1.1 Interface areas ................................................................................... 4

1.2 Key’s List and LEDs ............................................................................. 5

2 - GETTING STARTED WITH THE BI-TRONIC CONTROL INTERFACE 6

2.1 Getting started.................................................................................... 6

2.2 Setting the clock................................................................................. 6

3 - EXAMPLE OF USE................................................................ 7

3.1 Operating mode .................................................................................. 7

3.1.1 Direct mode...................................................................................................... 7

3.1.2 Retarder proving cycle mode ........................................................................... 7

3.2 Direct mode ........................................................................................ 8

3.2.1 To change the temperature .......................................................................... 8

3.2.2 To change the humidity rate ......................................................................... 8

3.3 Cycle mode......................................................................................... 9

4 - FAULTS AND PARAMETERS .................................................. 12

5 - STOPPING THE CONTROL INTERFACE .................................. 13

Hengel Industrie

ZA, Les Berges du Rhins - 42120 PARIGNY - FRANCE

Tél : +33 (0)4 77 23 40 00 - Fax : +33 (0)4 77 23 40 09

Email: [email protected]

Website: www.hengel.com

Notice-EN-BITRONIC-ST-F-1 4

1 - GENERAL INTRODUCTION

The company HENGEL thanks you for your trust.

The interface BI-TRONIC CONTROL is simple and intuitive. It has a seven-segment display. It has the following

form:

1.1 Interface areas

Retarder proving cycle zone

Display of the temperature

and the humidity from direct mode

Setting the temperature and

humidity in direct mode

Start up and set

point adjustment area

Launching of the proving

in direct or cycle mode

Validation during

parameter setting

Display

Operating state

Hengel Industrie

ZA, Les Berges du Rhins - 42120 PARIGNY - FRANCE

Tél : +33 (0)4 77 23 40 00 - Fax : +33 (0)4 77 23 40 09

Email: [email protected]

Website: www.hengel.com

Notice-EN-BITRONIC-ST-F-1 5

1.2 Key’s List and LEDs

Button Description Indicator

light Description

- Press 1 s: start up of the interface

- Press 3 s: stop the cycle in progress

- Press 5 s: stop the machine

Attention, the On/Off key puts the

interface in stand-by mode.

By no means, it turns off the

machine. To do this, you must

unplug the device.

Green LED: compressor in operation

Green LED blinking: compressor in demand

but not allowed

Green LED: fan in operation

Green LED blinking: fan in demand but not

allowed

Green LED: heating in operation

Red LED: fault

- Modication of a set point

- Increment of a unit

Green LED: temperature display

Orange LED blinking: temperature setting

- Modication of a set point

- Decrement of a unit

Green LED: humidity display

Orange LED blinling: humidity adjustment

- In cycle or direct mode: display of the

temperature or percentage of hygrometry

- In direct mode, change to hygrometry /

temperature setting

Green LED: cycle during a blocking period

Orange LED blinking: blocking temperature

setting

Direct launch (unlimited time)

Green LED: cycle during proving

Orange LED blinking: proving temperature

setting

Launch retarder proving cycle

Green LED: cycle during proving

Orange LED blinking: adjustment of the

hygrometry rate

Validate / Save changes Green LED: cycle during fermentation

Orange LED blinking: setting the proving time

Hengel Industrie

ZA, Les Berges du Rhins - 42120 PARIGNY - FRANCE

Tél : +33 (0)4 77 23 40 00 - Fax : +33 (0)4 77 23 40 09

Email: [email protected]

Website: www.hengel.com

Notice-EN-BITRONIC-ST-F-1 6

2 - GETTING STARTED WITH THE BI-TRONIC CONTROL INTERFACE

2.1 Getting started

14:30

OFF

14:30

16:30

16:32

When rst switching on the device, the device is ready

for operation.

To turn it on, press the “On / Off” key for 1 second.

The display lights up and indicates the time.

2.2 Setting the clock

If the indicated time is not correct, press the “Plus” or

“Minus” key.

HOURS BLINK.

Adjust the hour by pressing the “Plus” or “Minus”

keys. When the hour is correct, press the “Validate”

key.

MINUTES BLINK.

We must operate in the same way as for the hours.

The display remains xed and indicates the previously

set time.

1 s

Hengel Industrie

ZA, Les Berges du Rhins - 42120 PARIGNY - FRANCE

Tél : +33 (0)4 77 23 40 00 - Fax : +33 (0)4 77 23 40 09

Email: [email protected]

Website: www.hengel.com

Notice-EN-BITRONIC-ST-F-1

3 - EXAMPLE OF USE

3.1 Operating mode

There are 2 modes of operation:

3.1.1 Direct mode

T °C

Time

H %

Proving

T° set

point

6 °C

Proving

Stop

direct mode

Products

insertion

Start

direct mode

~ 30 mn

Hygrometry is active

when temperature> 6 ° C

3.1.2 Retarder proving cycle mode

T °C

Time

H %

15 °C

~ 30 mn

Proving cycle

time set point

6 °C

-5 °C

Blocking Proving Back in cold

End

cycle

Start

cycle

Proving

T° set

point

Blocking

T° set

point

Products

insertion

Hygrometry is active

when temperature> 6 ° C

Hengel Industrie

ZA, Les Berges du Rhins - 42120 PARIGNY - FRANCE

Tél : +33 (0)4 77 23 40 00 - Fax : +33 (0)4 77 23 40 09

Email: [email protected]

Website: www.hengel.com

Notice-EN-BITRONIC-ST-F-1

3.2 Direct mode

The DIRECT operating mode allows the cabinet to be set at dened temperature and humidity settings before

introducing the dough.

This is a simplied cycle. The temperature and humidity set points will not change automatically until the cycle

is stopped manually or the set points are manually changed.

When rst switching on the device, the device is ready

for operation.

To turn it on, press the “On / Off” key for 1 second.

The display lights up and shows the time.

To set the time, see section 2.2 Clock programming.

To start the direct proving mode, press the “Direct

launch” key. The temperature and hygrometry

previously entered will be taken into account.

The cycle is started, the display alternates between the

current temperature and the current cycle animation.

3.2.1 To change the temperature

Press the “Plus” or “Minus” key.

The temperature indicator blinks in orange.

Change the value by pressing the “Plus” or “Minus”

.keys. Save changes by pressing “Validate”

3.2.2 To change the humidity rate

Press the «Plus» or «Minus» key and then the «T ° /

H%» key.

The hygrometry indicator blinks in orange.

Change the value by pressing the “Plus” or “Minus”

buttons. Save changes by pressing “Validate”.

Note: During these operations the machine continues to operate. New set points are taken into account when

they are saved (they do not blink anymore).

To stop the cycle, press the “On / Off” button for 3

seconds.

It is then possible to stop the machine. Press the “On

/ Off” button for 5 seconds.

The display shows “Off”.

14:30

15.0

27.0

70.0

29.5

OFF

3 s

5 s

1 s

Hengel Industrie

ZA, Les Berges du Rhins - 42120 PARIGNY - FRANCE

Tél : +33 (0)4 77 23 40 00 - Fax : +33 (0)4 77 23 40 09

Email: [email protected]

Website: www.hengel.com

Notice-EN-BITRONIC-ST-F-1

3.3 Cycle mode

The regulator allows to launch a retarder proving cycle for 24, 48 or 72h.

14:30

24h

OFF

When rst switching on the device, the device is ready

for operation.

To turn it on, press the “On / Off” key for 1 second.

The display lights up and shows the time.

To set the time, see section 2.2 Clock programming.

To start the cycle, press the “Start Cycle” key.

DURATION OF THE CYCLE

The screen offers a cycle time of 24, 48 or 72h.

Adjust your choice with the “Plus” or “Minus” buttons

and press the “Validate” button.

TIME WHEN THE PROVING WILL BE COMPLETED

Indicate the time at which you want to get the dough

back using the “Plus” or “Minus” buttons then

“Validate”.

THE CYCLE IS LAUNCHED

The display alternates between the current

temperature and the current cycle animation. The

last recorded values of blocking temperature, proving

temperature and hygrometry rate are took back.

Note: The factory default values are:

Blocking: 4 °C

Proving: 25 °C

Humidity rate: 75 %

Proving time: 2 h

In order to facilitate the temperature reduction of the products, it is important to introduce them into

an already cold room. This is the goal of the rst phase of the cycle. This phase lasts 20 minutes. It

is therefore necessary to start the fermentation cycle approximately 30 minutes before the products

are introduced into the chamber.

15.0

1 s

Hengel Industrie

ZA, Les Berges du Rhins - 42120 PARIGNY - FRANCE

Tél : +33 (0)4 77 23 40 00 - Fax : +33 (0)4 77 23 40 09

Email: [email protected]

Website: www.hengel.com

Notice-EN-BITRONIC-ST-F-1

4.0

25.0

3.5

27.2

3.3.1 CHANGE SET POINTS

Press the “Plus” or “Minus” key.

The blocking temperature LED blinks in orange and

the display shows a temperature.

Adjust the temperature using the “Plus” and “Minus”

buttons, then “Validate”.

Then, the proving temperature LED blinks in orange.

Adjust the temperature using the “Plus” and “Minus”

buttons, then “Validate”.

Then, the hygrometry LED blinks in orange. Adjust

the rate using the “Plus” and “Minus” buttons, then

“Validate”.

Then, the proving time LED blinks in orange. Adjust

the time using the “Plus” and “Minus” buttons, then

“Validate”.

70.0

4:30

75.0

5:00

Other manuals for Bi-Tronic Control

Table of contents

Other hengel Control Unit manuals

hengel

hengel Bi-Tronic Control User manual

Popular Control Unit manuals by other brands

Festo

Festo Compact Performance CP-FB6-E Brief description

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Quick installation guide

JS Automation

JS Automation MPC3034A user manual

JAUDT

JAUDT SW GII 6406 Series Translation of the original operating instructions

Spektrum

Spektrum Air Module System manual

BOC Edwards

BOC Edwards Q Series instruction manual

KHADAS

KHADAS BT Magic quick start

Etherma

Etherma eNEXHO-IL Assembly and operating instructions

PMFoundations

PMFoundations Attenuverter Assembly guide

GEA

GEA VARIVENT Operating instruction

Walther Systemtechnik

Walther Systemtechnik VMS-05 Assembly instructions

Altronix

Altronix LINQ8PD Installation and programming manual

Eaton

Eaton Powerware Series user guide

WAGO

WAGO 750-407/040-000 manual

Sony

Sony CCU-590 Operation manual

Graco

Graco 25D614 instructions

Task Force Tips

Task Force Tips YE-RF-900 Instructions for installation, safe operation and maintenance

Shini

Shini SPV-U Series manual