Heatmax SRFP12119R Assembly instructions
OWNER'S MANUAL AND ASSEMBLY INSTRUCTIONS
Model Number: SRFP12119R
22-in Smokeless Fire Pit
KEEP THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE.
WARNING
ADULT ASSEMBLY REQUIRED.
Keep screws, nuts and parts out of reach of children.
CUSTOMER SERVICE: 1-888-909-3888
Monday - Friday, 7:30 a.m. – 4:30 p.m., PST
!
ASSEMBLY INSTRUCTIONS
CARE AND MAINTENANCE
WARRANTY INFORMATION
WARNINGS 1-2
3
4-7
9
10
PARTS AND HARDWARE
TABLE OF CONTENTS
PRODUCT USE OR INSTRUCTIONS 8
•
•
Keep this manual for future reference. It contains useful information
and important procedures for maintenance and safety.
If any parts are missing, do not attempt to assemble the fire pit. Call Customer
Service to request replacement parts.
Read the Assembly section completely before beginning the assembly process. This
will allow you to become familiar with parts and steps. In some cases, it might be
necessary to leave hardware loose for further assembly steps.
BEFORE ASSEMBLY:
•Verify all the parts are included BEFORE you begin assembly. Refer to the Parts Lists
section. For your convenience, some parts might be pre-assembled or attached to
fire pit components.
1. DO NOT use this fire pit without reading this entire document and all WARNINGS, cautions and
instructions.
2. This item is for outdoor use only, and shall NOT be used in a building, garage or any other
enclosed area.
3. DO NOT use this fire pit for indoor heating. TOXIC carbon monoxide fumes can accumulate and
cause asphyxiation or death.
4. This fire pit is NOT for commercial use.
5. This fire pit is NOT to be operated by children.
6. This fire pit is NOT to be used in or on boats or recreational vehicles.
7. Always use in accordance with all applicable local, state and national codes. Contact your local fire
department for details on outdoor burning.
8. When using this fire pit, exercise the same precautions you would with any open fire.
9. The use of alcohol, prescription or non-prescription drugs may impair the consumer’s ability to
properly assemble or safely operate this fire pit.
10. This fire pit is for use with dry, seasoned hardwood and pellet. It will burn hotter, more completely
and create less smoke.
11. DO NOT burn charcoal briquette, lump charcoal, manufactured logs, driftwood, trash, leaves,
papers, cardboard, plywood, painted or stainedor pressure treated wood. Avoid using softwoods
such as pine or cedar that can throw sparks.
12. DO NOT alter this fire pit in any manner.
13. DO NOT use this fire pit until it is COMPLETELY assembled and all parts are securely fastened
and tightened.
Save these instructions for future reference. If you are assembling this fire pit for someone
else, give this manual to him or her to save for future reference.
1. Improper installation, adjustment, alteration, service, or maintenance may result in
property damage, injury or death.
2. Read the installation, operation, maintenance instructions thoroughly before installing
or servicing this equipment.
3. Failure to follow these instructions could result in a fire or explosion, which could cause
property damage, personal injury or death.
WARNINGS
WARNING
!
For Outdoor Use Only
(outside any enclosure)
WARNING
!
WARNING
!
FOR YOUR SAFETY
1
WARNINGS
14. DO NOT store or use gasoline or other flammable vapors or liquids in the vicinity of this or any
other appliance.
15. DO NOT store or use an LP gas cylinder within 10 feet (3.05 m) of this fire pit while it is in operation.
16. DO NOT use this fire pit near automobiles, trucks, vans or recreational vehicles.
17. DO NOT use in an explosive atmosphere. Keep outdoor area clean and free from combustible
materials, gasoline and other flammable liquids.
18. DO NOT use this fire pit under an overhead or near any unprotected combustible constructions.
Avoid using near or under overhanging trees and shrubs.
19. Always use this fire pit on a hard level non-combustible surface such as concrete, rock or stone.
An asphalt or blacktop surface may not be acceptable for this purpose. DO NOT use on wooden decks.
20. Always empty this fire pit before each use.
21. DO NOT wear flammable or loose clothing when operating this fire pit.
22. DO NOT use in windy conditions.
23. DO NOT use gasoline, kerosene, diesel fuel, lighter fluid to relight fires.
24. Keep all electrical cords away from a hot fire pit.
25. All surfaces of this fire pit are hot when in operation. To avoid burns, do NOT touch fire pit until it
has completely cooled unless you are wearing protective gear (potholders, gloves, BBQ mittens, hot
pads etc). Never touch ashes or coals to see if they are hot.
26. DO NOT leave a lit fire pit unattended, especially around children and pets.
27. DO NOT attempt to move or store this fire pit until ashes and coals are completely extinguished.
28. DO NOT remove ashes or coals until they are completely extinguished.
29. Use heat-resistant gloves or hot pads when touching fire pit.
30. Do not add additional firewood until the fire burns down.
31. DO NOT lean over this fire pit when lighting or when in use.
32. Avoid breathing smoke from the fire and avoid getting it into your eyes.
33. This fire pit should be thoroughly inspected and cleaned on a regular basis.
34. After a period of storage and/or non-use, check for signs of damage and creosote build-up.
DO NOT operate until necessary repairs and/or clean up is executed.
35. Death, serious injury or damage to property may occur if the above is not followed exactly.
WARNING:
!
This product can expose you to chemicals including soot, which is known in the State of California to cause
cancer and reproductive toxicity，and carbon monoxide, which is known to the State of California to cause
birth defects or other reproductive harm. For more information, go to: www.P65Warnings.ca.gov.
2
3
Before beginning assembly of product, make sure all parts are present. Compare parts with package
contents list and hardware contents list.
Phillips screwdriver
1
HARDWARE CONTENTS
27
I
Step 2
Step 1
Attach the leg supports (G) to the legs (C) with (12) M4 x 10 screws (BB) as illustrated.
NOTE: Assemble the fire pit on a non-abrasive, level surface. If missing parts please contact
customer service.
BB x12
M4 x 10 Screw
Hardware Used
Attach the heat insulated plate (B) to the leg supports (G) with (6) M6 stepped screws (CC)
as illustrated.
ASSEMBLY INSTRUCTIONS
CC x 6
M6 Stepped Screw
Hardware Used
B
G
4
G
BB
C
B
CC
CC
G
Step 3
Attach the inner tube (D) to the fire bowl (A) with (6) M4 x 10 screws (BB) as illustrated.
Then place the bottom of fire bowl upward.
Note: The inner tube installation is optional. This step can be ignored, see instructions
on page 8.
ASSEMBLY INSTRUCTIONS
Step 4
Attach the leg assembly to the bottom of fire bowl (A) with (6) M6 x 10 screws (AA) as illustrated.
AA x6
M6 x 10 Screw
Hardware Used
AA
BB x6
M4 x 10 Screw
Hardware Used
5
A
A
D
BB
A
Step 5
Attach the baffles (E) to the bottom of fire bowl (A) with (9) M4 x 10 screws (BB) as illustrated.
BB x9
M4 x 10 Screw
Hardware Used
ASSEMBLY INSTRUCTIONS
Step 6
Place the ash tray (F) onto the heat insulated plate (B) as illustrated.
6
BB
E
F
H
Step 7
Place the cooking grid (H) onto the firebowl as illustrated.
ASSEMBLY INSTRUCTIONS
7
Lighting
Using firewood
1. Make sure there is no ash in the bottom of fire bowl.
2. Start by placing dry kindling and small wood pieces in the fire bowl.
3. Use a match to light kindling or small wood pieces.
4. As the ember bed gets hotter, start adding in 1-3 pieces of wood.
As those catch, add enough wood to fill the fire bowl.
Using wood pellets
1. Make sure there is no ash in the bottom of fire bowl.
2. Place 100% natural hardwood pellets in the fire bowl, and put
kindling or a natural fire starter on to the pellets.
Note: Do not overfill with pellets that covers or extends above the
top air holes.
3. Ignite the kindling or fire starter to allow the fire to start.
Extinguishing
1. Allow fire to burn itself out.
2. DO NOT use water to extinguish as this is dangerous and can cause damage to this outdoor fire pit.
Firewood placement #1
Inner tube installed Inner tube not installed
Firewood placement #2
Inner tube installed Inner tube not installed
Max usage: 33 LB, Min usage: 11 LB
4. If you need to add pellets, it is recommended to add near the end
of fire burning, and add pellets by batches, each time 1.1 ~ 2.2 lbs is appropriate.
PRODUCT USE OR INSTRUCTIONS
8
Table of contents
