Harvest TEC 890A User manual

#010-0890A

REVISED

03/12

OWNER’S MANUAL

Model 890A

Scale Interface Kit & GPS Attachment Kit for

AGCO

balers

HARVEST TEC 890A TABLE OF CONTENTS

PAGE

INTRODUCTION

OVERVIEW

INSTALLATION OF

PIP INTERFACE CONTROL

BOX

Installation of PIP Interface Control Box & Harness 4

Wiring Diagra 5

Setup Instructions 5

INSTALLATION OF GPS RECEIVER HA

RNESS

GPS Receiver Installation 6

GPS Harness Installation 6

Wiring Diagra 7

SETUP INSTRUCTIONS

OPERATING

INSTRUCTIONS

CONVERTING YIELD DATA FILE

PC Installation of Yield Data File Converter Progra 10

Converting Yield Data File 11

COMMON QUESTIONS ABOUT THE 890A

TROUBLE SHOOTING

WIRING DIAGRAMS

PARTS BREAKDOWN FOR MODEL 890A

NOTES 16

WARRANTY STATEMENT

BACK PAGE

***NOTE: Need to Purchase Garmin 16X HVS***

AGCO Part no. 1425350

INTRODUCTION

Congratulations on purchasing a Harvest Tec Model 890A Scale Interface & GPS Attach ent

Kit. This kit provides you with the ability to record yield apping files onto a USB flash drive

along with writing the exact bale weight into your job records. The kit will also write the rolling

average fro the last three bales weighed by the AGCO scale kit on the baler to the tag if

your baler is equipped with a Harvest Tec Model 850 Tagger (U.S. Patent 7,621,111B2 & U.S.

Patent 7,415,924B2). The 890A will only work with AGCO balers with the AGCO scale kit

installed. The yield apping portion of the kit will only work if you plug a Gar in 16X HVS into

the Interface box. For this kit to function at all your baler ust have the Harvest Tec Model

500 Moisture Monitor or Harvest Tec odel 565 Preservative Application Syste installed on

it.

OVERVIEW

There are two parts to the Harvest Tec Model 890A Precision Infor ation Processor (PIP)

Interface Control & GPS Attach ent Kit. The PIP Interface portion is designed to onitor the

bale scale CAN co unication and intercept the signal when it is trans itted. As this weight

is captured it is i ediately stored into the job records for that specific bale. If your baler is

equipped with a Tagger, as the signal is intercepted the 890A will use the data collected fro

the last three bales and write rolling averages to the tags. The data will then be readable

using a Harvest Tec Model 860 Scanner. The GPS attach ent portion is designed to interface

the Gar in 16X HVS into the 565/500 syste and have it collect GPS points to be processed.

With this processed data the PIP will create and store a yield files, save in a CSV for at, onto

the USB flash drive.

INSTALLATION OF PIP INTERFACE CONTROL BOX

Installation of PIP Interface Control Harness

The PIP Interface Controller (PIC) (006-5676) will ount next to the AGCO Bale Weighing

Controller. The AGCO Bale Weighing Controller will be located inside the right fender. Mark and

drill four 5/16 holes next to the bale scale and attach with four 1/4 x 1 “bolts and flange nuts.

Disconnect the harness plug shown above (figure 1). Connect the AGCO interface cable (006-

0890A) in the open port. Connect the AGCO scale harness plug into the other connection on the

AGCO interface cable. Connect the last connection into the PIC.

Locate a green ter inating resistor (006-5650Z) on the Harvest Tec Precision Infor ation Processor

(006-5671LS), Pu p Controller (006-5672), or Tagger Control (006-5673). The ter inating resistor

will be at different locations depending on the options installed. Re ove the resistor. Connect one

end of the co unication harness, found in the 890A kit (006-5650F) to the PIP Interface Control

box and the other connect to the open port were the ter inating resistor was re oved fro .

Figure 1

Wiring Diagram

Setup Instructions

1. Turn the 500/565 control syste on. After a few seconds the Main Menu screen should

appear. Press Setup Mode, the Setup Mode screen will then appear.

2. Press Baling Rate. The Bale Rate Settings screen will then appear.

3. Press the underline 0 next to bale scale. The keypad will then appear. Press 1 followed by

enter.

4. The scale is now active in the syste .

5. The AVG Bale Weight will now adjust for every bale being ade. If no signal co es fro the

scale it will default to your inputted value.

AGCO

Bale

Weighing

Controller

AGCO interface

cable

006

0890A

PIP Interface

Control Box

006

5676

Co unication

harness

006

5650F

Connection

at baler

Fig. 1

INSTALLATION OF GPS RECEIVER HARNESS

GPS Receiver Installation

Locate your Gar in 16X HVS. This should have been purchased through your AGCO dealer.

The GPS receiver will be hard ounted on top of your baler in the area of the isstie flag

indicators. If the isstie flag indicators are not present find a flat surface near the knotter

cover/door. This location should give the GPS receiver the best chance at receiving the strongest

satellite signal.

GPS Harness Installation

Once the Gar in GPS receiver has been installed, route the harness to the right side of the

baler. The harness needs to be plugged into the PIP Interface Control (PIC) box that was

included in the 890A kit, so using the zip ties provided, fasten the harness securely to the baler

routing it safely towards the PIC box ounting location. (***Note: ake sure wiring harnesses are

not in any pinch points and will not co e in contact with oving parts on the baler.) Once the

harness as been routed and secure, locate the GPS adapter harness (006-5650GPS2) included

in the 890A kit. This is the adapter harness that the GPS harness plugs into so that it can be

interfaced into PIC. Plug the GPS adapter harness into the port labeled “Port 4” on the PIC.

*****Wiring directions for balers without AGCO bale weighing scale installed:

Locate a green ter inating resistor (006-5650Z) on the Harvest Tec Precision Infor ation

Processor (006-5671LS), Pu p Controller (006-5672), or Tagger Control (006-5673). The

ter inating resistor will be at different locations depending on the syste installed on the baler.

Re ove the resistor. Connect one end of the co unication harness (found in the 890A kit 006-

5650F) to the PIC, and the other connect to the open port were the ter inating resistor was

re oved fro .

Wiring Diagram

Gar in GPS 16X HVS

GPS adapter harness

006-5650GPS2

PIP Interface Control Box

006-5676

006-5650F

Connection

at baler

Fig. 1 (look

at pg 4 &5

AGCO

Bale

Weighing

Controller

SETUP INSTRUCTIONS

1. Turn the 565 control syste on. After a few seconds the Main Menu screen should appear.

Press Setup Mode, the Setup Mode screen will then appear.

2. Press Yield Mapping setup.

a. Yield Mapping Setup should now be displayed.

3. Press the underlined value next to Swath Width (Ft). Enter in the swath width that will be

baled, press Enter to confir .

4. Press the underlined value next to GPS. Enabling/Disabling will require entering the

appropriate value. 0 to Disable, 1 to Enable. Press Enter to confir .

5. Make sure the USB flash drive is inserted into the PIP’s Data Transfer port before

baling. Without the USB flash drive a yield file will not be created. (USB flash drive

provided in the 880 kit)

USB flash

drive

OPERATION INSTRUCTIONS

1. Once installation and setup is co plete the syste is ready for baling. There is a GPS

indicator icon that will appear in either of the Auto atic or Manual ode screens. The GPS

icon shows the user that the GPS is trans itting data to the PIP to be processed. The GPS

icon, if getting a good satellite signal, will continually increase/decrease in size. While all this

is going on a Yield file is being created and saved to the USB flash drive. Additionally as you

enter the Auto atic/Manual ode work screens an alert essage will appear above the

Override key. This the alert essage will display “Opening USB flash” and if the PIP locates

the USB flash drive successfully the alert essage will disappear and the yield data will be

written too the flash drive. If a different alert essage is being displayed see pg. 12 for

troubleshooting.

2. Once baling is co plete, create a New Job and the yield data file that was written to the USB

flash drive will be co plete and ready to be converted. See CONVERTING YIELD DATA

FILE for the next step.

****NOTE: If you’re a first ti e user, begin with the

INSTALLATION OF YIELD DATA FILE

CONVERTER PROGRAM before atte pting to convert the yield data file.

GPS

ICON

CONVERTING YIELD DATA FILE

PC Installation of Yield Data File Converter Program

1. Plug the USB flash provided in the 880 kit into the USB port on the co puter.

2. The USB flash will have a zipped file on it and will be labeled ydConverterSetup-V1_0_0_0.

a. Double click on that folder to open it and there will be two files inside labeled setup &

ydConverterSetup. Double click on ydConverterSetup.

b. A setup screen will appear, click Next.

c. The next screen will ask you what folder you would like to save the File Converter

Progra in. Use the default option and click Next to accept. Next a confir ation screen

will appear, press Next to confir . The co puter will then let the Yield File Converter

Progra install itself (Co puter will take up to a 1 in to save the yield file converter

progra to its desktop).

d. Once the progra has been installed you will see and Icon on the co puters desktop

as pictured above.

Popular Recording Equipment manuals by other brands

KV2 Audio

KV2 Audio 500 Series user guide

Robotics Technologies

Robotics Technologies microBus-Cam II installation manual

Seca

Seca 460 quick start guide

Cognex

Cognex MVS-8000 Series Hardware manual

Mect

Mect MPNC006 Series user manual

Bad Caf

Bad Caf THE LEASH operating manual

Strymon

Strymon NIGHTSKY user manual

Mitsubishi Electric

Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U user manual

Tews Technologies

Tews Technologies TPMC465 user manual

Honeywell

Honeywell Excel 50 user guide

SeaLevel

SeaLevel COMM+8.LPCI user manual

Arturia

Arturia AUDIOFUSE STUDIO user manual

Rukra

Rukra RK-1240 quick start guide

Samson

Samson SCOM owner's manual

Dynacord

Dynacord DPS260 owner's manual

Nice

Nice Core user manual

Pyle Pro

Pyle Pro PSS8 manual

RF-System

RF-System TinyGate Assembly and user's manual