Harol SC900 User manual
INSTALLATION INSTRUCTIONS
SUN PROTECTION
PROTECTION SOLAIRE
SHUTTERS
VOLETS
GATES
PORTES
SURFACE-MOUNTED SCREEN
SC900 - SC910
art.no. 60447
INSTALLATION INSTRUCTIONS SURFACE-MOUNTED SCREEN SC900 - SC910
03/15 |2
TABLE OF CONTENTS
1. INTRODUCTION 3
2. GENERAL WARNINGS 3
3. LIST OF TOOLS REQUIRED 4
4. INSTALLATION STEPS 5
4.1. Determine the type of screen 5
4.2. Check the package 5
4.3. Check the product 5
4.4. Check the height and width 5
4.5. The actual assembly in 10 steps 6
4.6. Installation of two or more adjacent screens 14
4.7. Checking the assembly 16
5. ELECTRICAL CONNECTIONS 17
5.1. Connection diagram for a single pole switch 17
5.2. Adjusting the motor - limit switches 18
6. TROUBLESHOOTING AND REPAIRS 20
6.1. The screen will not roll up or down 20
6.2. The motor hums 20
6.3. The motor does not stop in time 20
6.4. Bottom lath is slanted at the top 20
6.5. Bottom lath drops out of the lateral guides 20
6.6. The fabric tension is too slack; the bottom lath sticks
or shudders when the screen is lowered or raised 20
6.7. Folds and waves in the fabric 20
6.8. The direction of the motor’s rotation does not match the arrows on the switch 20
6.9. The fabric does not stop and roll up again 20
6.10. Automatic control does not operate properly 21
6.11. The bottom lath sticks or shudders when the screen is lowered or raised 21
7. REPAIRS 21
8. DISMANTLING AND REMOVAL 21
9. NOTES 22
INSTALLATION INSTRUCTIONS SURFACE-MOUNTED SCREEN SC900 - SC910
03/15 |3
1. INTRODUCTION
The SC900 screen is a flat hanging sun screen, which is fitted on top of the window with
a'zipper system' on each side of the fabric. This makes the screen particularly resistant to high
winds and keeps the fabric perfectly in place. In the down position the screen keeps out the
sun's rays, which can cause overheating, while at the same time it gives a view to the outside.
Moreover, this screen oers practical protection against insects, as the space between the
box, the guide rails and the fabric is completely sealed o.
The SC900 can also be fitted with fabrics that are almost fully opaque, making it especially
suitable to black out presentation rooms in oce buildings, laboratories, hospitals etc.
The installation of this sun protection system is explained step by step in these instructions.
The SC910 screen is a flat hanging sun screen with the same properties, but without the
insulation and cover (for the box). It is basically a 'naked' version of the SC900 screen.
Attention!
Open box, standard version without the back covered. This version requires a suitable
finish to avoid damage to and prevent dirt from settling on the fabric. (possible option =
full support plate instead of brackets)
2. GENERAL WARNINGS
A number of precautions have to be taken for the safe installation, operation and maintenance
of this screen. Please take notice of the following warnings for the safety of everyone concerned!
!These instructions have been drawn up for use by trained installers and therefore are
not suitable for use by amateurs or trainees.
!Please read these instructions carefully before starting the installation.
!Proceed carefully. Ensure that you have a robust footing.
!Make sure there is adequate lighting in the place of assembly. Remove any obstacles
and dirt. Ensure that no other persons other than the installers are present.
Unauthorised persons can get in the way or be at risk during the installation.
!The screen must be kept clearly in view at all times during installation and operation.
Persons in the vicinity may be at risk of injury.
!The installer must comply with the local regulations and standards with regards to
electrical connections.
!Our products must be installed in such a way that all parts remain accessible at all times
for maintenance and repairs. If this is not the case, Harol cannot be held responsible for
any additional costs (e.g. demolition work, repairs to exterior or interior walls) whichmay
result from this.
INSTALLATION INSTRUCTIONS SURFACE-MOUNTED SCREEN SC900 - SC910
03/15 |4
Guarantee, terms and conditions
• Harol has endeavoured to design and manufacture the screen in compliance with
the current CE standards. Always check that our version complies with your own
national standards institute.
• No rights can be derived from these instructions whatsoever. Technical modifications
are reserved without written notification.
• For large projects we strongly advise you to first fit 1 complete awning before fitting
the remaining awnings. This will help detect any potential faults early on and enable
them to be remedied at the lowest possible cost.
• For our general terms and conditions of sale, please refer to the price list.
• Make sure the screen box can always be opened so the mechanical parts inside can
be reached easily. If these rules are not respected, Harol cannot be held responsible
for the cost of demolition work or any paint work or wallpapering.
Harol NV
Industriepark 3 – 3290 Diest
Belgium
+32 (0)13 38 01 11
+32 (0)13 31 48 03
info@harol.be
www.harol.com
3. LIST OF TOOLS REQUIRED
• Ladder(s)
• Tape measure and pencil
• Cross-slotted screwdrivers
• Spirit level, plumb line or water hose
• Drill
• Set of drills
• Voltage meter or 220 V testing lamp
INSTALLATION INSTRUCTIONS SURFACE-MOUNTED SCREEN SC900 - SC910
03/15 |5
4. INSTALLATION STEPS
4.1. Determine the type of screen
Check the type of screen: SC900 (with insulation) or SC910 (without insulation)
4.2. Check the package
Check the package for any damage before removing the complete packaging from around
the box and guide rails.
4.3. Check the product
Check the product: ensure all guide rails and clip profiles are included and check if each
guide rail contains a holder with zipper profile.
Also check the bag with accessories. Verify that the screws for securing the support plate,
the clips for the bottom profile and the screws for securing the clip and bottom profiles
are there, together with the guarantee card.
4.4. Check the height and width
Check the width of the screen box and measure the window opening.
Verify that both match the desired mounting position.
Also check the height of the guide rails, including the end stop, and make sure they
correspond to the height of the window.
In the following steps logos are used to show the dierence between mounting the SC900
and SC910 screens.
SC900 SC910
INSTALLATION INSTRUCTIONS SURFACE-MOUNTED SCREEN SC900 - SC910
03/15 |6
4.5. The actual assembly in 10 steps
Step 1
• Remove the cover and the insulation.
• (SC900) The support plate and base plate are connected. The advantage of thisis
that the base plate does not bend when handling the box. Remove these screws
before mounting the screen!
• (SC910) Unscrew the brackets or support plate (optional) at the bottom, to free the
base plate.
SC900
SC910
SC900
SC900 SC910
INSTALLATION INSTRUCTIONS SURFACE-MOUNTED SCREEN SC900 - SC910
03/15 |7
• Then unscrew the two screws at the back that connect to the base plate.
Step 2
• Carefully let the base plate slide from the box.
Please note that this operation must be carried out on both sides of the box
before proceeding to the next step.
SC900
SC910
SC900
SC910
INSTALLATION INSTRUCTIONS SURFACE-MOUNTED SCREEN SC900 - SC910
03/15 |8
Step 3
• Centre the base plate on the window and screw it down.
• Make sure the base plate is correctly centred on the window.
• Distance (A) must be the same on both sides.
Tab at the bottom of the base profile forms the abutment with the window.
SC900
SC910
The touch component
for the bottom lath of
the SC910 screen is supplied
separately. This is mounted on
the base plate at a later stage!
INSTALLATION INSTRUCTIONS SURFACE-MOUNTED SCREEN SC900 - SC910
03/15 |9
Step 4
• Attach the clip profiles with the hole in a downward position.
• First position the upper side of the clip profile against the tab on the bottom side of
the base plate (Fig. 1a-1b).
• Next, drill holes at regular intervals to secure the clip profile and attach it to the window.
• In the bottom pre-drilled hole, the clip profile must be secured together with the end
stop (Fig. 2).
Make sure the clip profiles are mounted perpendicular, and check the diagonals
(see 4.6).
There is a hole in the clip profile to secure the end stop (Fig. 2).
Fig. 1a
Fig. 1b
Fig. 2
SC900
SC910
INSTALLATION INSTRUCTIONS SURFACE-MOUNTED SCREEN SC900 - SC910
03/15 |10
Step 5
• Clip both lateral guides - together with the holder with zipper profile - onto the
clipprofile.
• No screws are required!
Plan view of the clip profile
and guide rail
SC900
SC910
This manual suits for next models
1
Table of contents
Other Harol Tent manuals
