Hardi Master-MB Series User manual

Master-MB

Assembly

Instruction

672203-GB-96/11

Preassembly information

The sprayer is supplied ex-works in shipping packages. Number of

packages per sprayer varies depending on the model. This covers all

MA-MB models so please note only the fittings covering your model.

Removal of the plastic bag covering the tank is easiest done before

assembly.

Some components are shipped within the tank. Check inside.

The directions „right“ and „left“ are described when facing the direction

of travel.

CE marking for EU countries

From January 1995, all machines sold in EU countries must be CE

marked. The following must be done before a new machine can be

delivered.

1. Assembly and test all functions of the sprayer.

2. Fill in the EU Declaration of Conformity in the instruction book.

(sprayer order no., and full description, etc).

3. Adhere the self-adhesive CE mark with correct inscription to the

tank frame on a dry clean surface. Adhere the protection film on

top of the CE mark.

NOTE: The self-adhesive CE mark and protection film needs to

harden for 24 hours.

4. Fill in the customer file with customer name, address and sprayer

data (full description, shipping packages and shop order numbers).

Each shipping package contains two labels with the number of the

package. One label is for the customer file as described, the other is

for the instruction book. Adhere the labels on the inside cover of the

instruction book.

Packaging information

Materials used for packaging are environmentally compatible. They

can be safely deposited or they can be burnt in an incinerator.

Recycling

Cardboard: Can recycle up to 99% and therefore should be put into the

waste collection system.

Polystyrene foam: Can be recycled. Fluorocarbons (CFC) not used in

foam production.

Polyethylene: Can be recycled.

HARDI INTERNATIONAL A/S reserves its right to make any necessary improvements or

changes without previous notice, and without any obligation to make such changes of machines

and equipment which have already been bought or delivered.

1. Check all shipping packages are present.

NOTE: Use O-rings where indicated. Lubricate them with non-mineral lubri-

cant before assembly.

Model 1202/1302

2. Tee with O-ring and pressure damper are fixed to the frame.

Tee with O-ring and suction damper are mounted to the

pump.

Elbow and nipple are mounted to pressure outlet.

Use sealing tape. Turn elbows to the left.

Fit pump to base plate.

Use staggered brackets.

Model 361

2. Elbow is mounted to suction inlet.

Elbow and nipple are mounted to pressure outlet. Use sealing tape.

Turn elbows to the left.

Fit pump to base with M10 x 20 bolts.

ø 30 x 26 x 2

M6 x20

3. Fit bottom half of protective

guard.

Lubricate conical or splined

shaft lightly and connect

transmission shaft and fit

cover. Attach chain to pre-

vent rotation of the protec-

tive guard.

For conical connection

recheck the grub screw is

tight after 5 min. of usage.

Level indicator

4. Tube holders and tube are

fitted. With the float resting

on the stop pin at the bottom

of the rod, the O-ring on the

indicator must be positioned

at the top position line A.

Remove plug Band loosen

screws Cto alter position.

6. Fit operating unit to rack

arm and arm holder. The

holder can be shortened if

necessary.

Place nozzle in the agitation

valve and fit the assembly.

7. See back of pressure

gauge. Pierce casing and fit

gauge. Use sealing tape.

Do not overtighten.

BK operating unit

5. Place ball in the

main ON/OFF

valve and turn the

handle so the ball

disappears. Fit

valve seat and

connect main

valve to the distri-

bution valves.

8. Mount MANIFOLD fittings

(and eventual valves). Now bolt

bracket to the left hand side.

9. Check the agitation nozzles do not point towards yellow suction pipe.

If necessary, secure with plastic strap.

10.Insert filter and guide

(guide at top).

11.Fit hoses. Remember to lubricate O-rings before fitting.

A = From suction

filter to suction

manifold.

B = From pump

to pressure

damper.

C = From main

ON/OFF to tank.

D = From agitation

valve to tank.

E = From pressure equalization to

tank.

F = From distribution valves to boom.

Shortest for centre/inner section.

H = From HARDI-MATIC to tank.

K = From pressure manifold to safety valve.

M = From pressure mainfold to operating unit.

N = From Self Cleaning Filter (if fitted) to tank.

Use green restrictor for initial setup.

O = From suction manifold to pump.

Q = From pump or, pressure damper to pressure manifold.

Fit hoses inside the tank:

From main ON/OFF valve (hose C).

From HARDI-MATIC (hose H).

NOTE: For sake of good order, it may be necessary to shorten some hoses.

This is best done when assembly is completed and before hoses are se-

cured with plastic straps.

13.Bolt step and hose holder to

the right hand side.

12.Fit Self-Cleaning Filter to

right hand side tank brace.

Use green restrictor for initial

setup.

14.Connect hydraulic hose to

the ram. Remember the

spacer and secure with

split pins.

Fit the 4 bolts to the lift

wagon but do not tighten.

Lower wagon down the

gantry. Fit the pin and

secure with split pins.

Adjust glide pads Aso

distance Bis equal. Lubri-

cate glide pads.

15.Fit bridge and

centre part.

This manual suits for next models

Table of contents

Other Hardi Paint Sprayer manuals

Popular Paint Sprayer manuals by other brands

SNOWJOE

SNOWJOE Sunjoe 24V-GS-LTW-RM Operator's manual

Graco

Graco 246737 Repair and parts

Binks

Binks SV100 Service manual

Fimco

Fimco LG-4-3-1 owner's manual

AG SPRAY

AG SPRAY FS-ATV-25BL owner's manual

Nordson

Nordson MicroMax 2 manual

Bonide

Bonide 051 Operation and service instructions

zogics

zogics Z-DAS instruction manual

KISANKRAFT

KISANKRAFT KK-KBS-165 Operation manual

Matrix

Matrix SG 650 Translation of the original instructions

Anest Iwata

Anest Iwata SGA-3 Installation, use & maintenance instruction manual

paasche

paasche VV Instructions and parts list

Carlisle

Carlisle DeVilbiss JGA-510 Service manual

Gardena

Gardena 11120 Operator's manual

Conrad

Conrad Hobby Airbrush K3 operating instructions

wiwa

wiwa 14025 R/F operating manual

Graco

Graco EM 390 Instructions-parts list

DeVilbiss

DeVilbiss LUNA2i Operation manual