Hara Systems OSTSen-9250 User manual
OSTSen-9250 v1.0 1 of 9 Hara Systems Inc.
OSTSen-9250 User Guide
Ver 1.0
Hara Systems Inc.
OSTSen-9250 v1.0 2 of 9 Hara Systems Inc.
1. OSTSen-9250 Overview
OSTSen-9250 is a motion tracking module, which is based on InvenSense MPU-
9250. The MPU-9250 is a multi-chip(MCM) consisting of two dies integrated into a
single QFN package. One die houses the 3-Axis gyroscope and the 3-Axis
accelerometer. The other die houses the AK8963 3-Axis magnetometer from Asahi
Kasei Microdevices Corporation. Hence, the MPU-9250 is a 9-axis Motion Tracking
device that combines a 3-Axis gyroscope, 3-Axis accelerometer and a Digital Motion
Processor™(DMP) all in a small 3x3x1mm package available as a pin-compatible
upgrade from the MPU-6515. With its dedicated I2C sensor bus, the MPU-9250
directly provides complete 9-Axis MotionFusion™ output. The MPU-9250 Motion
Tracking device, with its 9-axis integration, on-chip Motion Fusion™, and run-time
calibration firmware, enables manufacturers to eliminate the costly and complex
selection, qualification, MPU-9250 is also designed to interface with multiple non-
inertial digital sensors, such as pressure sensors, on its auxiliary I2C port.
MPU-9250 features three 16-bit analog-to-digital converters(ADCs) for digitalizing
the gyroscope outputs, three 16-bit ADCs for digitalizing the magnetometer outputs.
For precision tracking of both fast and slow motions, the parts feature a user-
programmable gyroscope full-scale range of ±250, ±500, ±1000, and
±2000°/sec(dps), a user-programmable accelerometer full-scale range of ±2g, ±4g,
±8g and ±16g, and a magnetometer full-scale range of ±4800uT.
Other industry-leading features include programmable digital filters, a precision
clock with 1% drift from -40°C to 85°C, an embedded temperature sensor, and
programmable interrupts. The device features I2C and SPI serial interfaces, a VDD
operating range of 2.4V to 3.6V, and separate digital IO supply, VDDIO from 1.71V to
VDD.
Communication with all register of the device is performed using either I2C at
400kHz or SPI at 1MHz. For application requiring faster communications, the sensor
and interrupt registers may be read using SPI at 20MHz.
By leveraging its patented and volume-proven CMOS-MEMS fabrication platform,
which integrates MEMS wafers with companion CMOS electronics through wafer-
level bonding, InvenSense has driven the package size down to a footprint and
thickness of 3x3x1mm, to provide a very small yet high performance low cost
package. The device provides high robustness by supporting 10,000g shock
reliability.
2. Application
· Location based services, points of interest, and dead reckoning
· Handset and portable gaming
· Motion-based game controllers
· 3D remote controls for Internet connected DTVs and set top boxes, 3D mice
· Wearable sensors for health, fitness and sports
3. Features of MPU9250
3.1 Gyroscope Features
The triple-axis MEMS gyroscope in the MPU-9250 includes a wide range of features:
· Digital-output X-, Y-, and Z-Axis angular rate sensors (gyroscopes) with a user-
programmable full-scale range of ±250, ±500, ±1000, and ±2000°/sec and
integrated 16-bit ADCs
· Digitally-programmable low-pass filter
OSTSen-9250 v1.0 3 of 9 Hara Systems Inc.
· Gyroscope operating current: 3.2mA
· Sleep mode current: 8uA
· Factory calibrated sensitivity scale factor
· Self-test
3.2 Accelerometer Features
The triple-axis MEMS accelerometer in MPU-9250 includes a wide range of features:
· Digital-output triple-axis accelerometer with a programmable full scale range of ±2g,
±4g, ±8g and ±16g and integrated 16-bit ADCs
· Accelerometer normal operating current: 450uA
· Low power accelerometer mode current: 8.4uA at 0.98Hz, 19.8uA at 31.25Hz
· Sleep mode current: 8uA
· User-programmable interrupts
· Wake-on-motion interrupt for low power operation of application processor
· Self-test
3.3 Magnetometer Features
The triple-axis MEMS magnetometer in MPU-9250 includes a wide range of features:
· 3-axis silicon monolithic Hall-effect magnetic sensor with a magnetic concentrator
· Wide dynamic measurement range and high resolution with low current
consumption
· Output data resolution is 14 bit (0.6μT/LSB)
· Full scale measurement range is ±4800 μT
· Magnetometer normal operating current: 280uA at 8Hz repetition rate
· Self-test function with internal magnetic source to confirm magnetic sensor
operation on end products
3.4 Additional Features
The MPU-9250 includes the following additional features:
· Auxiliary master I2C bus for reading data from external sensors (e.g., pressure
sensor)
· 3.5mA operating current when all 9 motion sensing axes and the DMP are enabled
· VDD supply voltage range of 2.4 ~ 3.6v
· VDDIO reference voltage for auxiliary I2C devices
· Smallest and thinnest QFN package for portable devices: 3x3x1mm
· Minimal cross-axis sensitivity between the accelerometer, gyroscope and
magnetometer axes
· 512 byte FIFO buffer enables the application processor to read the data in bursts
· Digital-output temperature sensor
· User-programmable digital filters for gyroscope, accelerometer, and temp sensor
· 10,000 g shock tolerant
· 400kHz Fast Mode I2C for communicating with all registers
· 1MHz SPI serial interface for communication with all registers
· 20MHz SPI serial interface for reading sensor and interrupt registers
· MEMS structure hermetically sealed and bonded at wafer level
· RoHS and Green compliant
OSTSen-9250 v1.0 4 of 9 Hara Systems Inc.
4. Application Information
4.1 Module Pin Out and Signal Description
Pin
Number
Pin Name
Pin Description
1
VCC
Power supply voltage
2
GND
Power supply ground
3
SCL
I2C serial clock(SCL); SPI serial clock(SCLK)
4
SDA
I2C serial data(SDA); SPI serial data input(SDI)
5
AD0
I2C Slave Address LSB (AD0); SPI serial data output(SDO)
6
NCS
Chip select (SPI mode only)
7
INT
Interrupt digital output (totem pole or open-drain)
8
ADA
Auxiliary I2C master serial data
9
ACL
Auxiliary I2C master serial clock
10
FSYNC
Frame synchronization digital input.
Connect to GND if unused
< TopView >
+Z
+Z
+Y
+Y
+X
+X
+Z
+X
+Y
Orientation of Axes of Sensitivity
and Polarity of Rotation
for Accel & Gyro
Orientation of Axes of
Sensitivity for Magnetometer
VCC
GND
SCL
SDA
NCS
INT
FSYNC
ADA
1
2
4
6
3
10
8
7
AD0
ACL
5
9
OSTSen-9250 v1.0 5 of 9 Hara Systems Inc.
4.2 MPU-9250 Pin out and Signal Description
Pin Number
Pin Name
Pin Description
1
RESV
Reserved. Connect to VDDIO
7
AUX_CL
I2C master serial clock for connecting to external sensors
8
VDDIO
Digital I/O supply voltage
9
AD0/SDO
I2C Slave Address LSB (AD0); SPI serial data output(SDO)
10
REGOUT
Regulator filter capacitor connection
11
FSYNC
Frame synchronization digital input.
Connect to GND if unused
12
INT
Interrupt digital output (totem pole or open-drain)
13
VDD
Power supply voltage and Digital I/O supply voltage
18
GND
Power supply ground
19
RESV
Reserved. Do not connect
20
RESV
Reserved. Connect to GND
21
AUX_DA
I2C master serial data, for connecting to external sensors
22
nCS
Chip select (SPI mode only)
23
SCL/SCLK
I2C serial clock(SCL); SPI serial clock(SCLK)
24
SDA/SDI
I2C serial data(SDA); SPI serial data input(SDI)
2~6, 14~17
NC
Not internally connected May be used for PCB trace routing
l MPU-9250 I2C 7bit device address: 0x69 ( in module : AD0 is HIGH )
0x68 ( in module : AD0 is LOW )
MSB
LSB
1
1
0
1
0
0
X
R/W
OSTSen-9250 v1.0 6 of 9 Hara Systems Inc.
5. Module Dimension
< OSTSen-9250 module >
12.065mm
10.16mm
2.54mm
1
2
4
6
3
10
8
7
5
9
OSTSen-9250 v1.0 7 of 9 Hara Systems Inc.
6. I2C Communications
OSTSen-9250 v1.0 8 of 9 Hara Systems Inc.
7. Demo System
OSTSen-9250 Data Display on PC
32 bit
Processor
USB
VCC
GND
SCL
SDA
PC
Demo System
USB
OSTSen-9250 v1.0 9 of 9 Hara Systems Inc.
8. Reference
1) https://www.invensense.com/products/motion-tracking/9-axis/mpu-9250/
2) https://www.invensense.com/wp-content/uploads/2015/02/PS-MPU-9250A-01-
v1.1.pdf
3) https://www.invensense.com/wp-content/uploads/2015/02/AN-IVS-0001EVB-00-
v1-3.pdf
4) https://github.com/kriswiner/MPU9250
5) https://github.com/sparkfun/SparkFun_MPU-9250-DMP_Arduino_Library
6) https://github.com/sparkfun/SparkFun_MPU-
9250_Breakout_Arduino_Library/tree/113e836e989699913660c60bacda12da4a91
9c91
l If you need some information or have some questions about OSTSen-9250,
Other manuals for OSTSen-9250
1
Other Hara Systems Control Unit manuals
Popular Control Unit manuals by other brands
Festo
Festo Compact Performance CP-FB6-E Brief description
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Quick installation guide
JS Automation
JS Automation MPC3034A user manual
JAUDT
JAUDT SW GII 6406 Series Translation of the original operating instructions
Spektrum
Spektrum Air Module System manual
BOC Edwards
BOC Edwards Q Series instruction manual
KHADAS
KHADAS BT Magic quick start
Etherma
Etherma eNEXHO-IL Assembly and operating instructions
PMFoundations
PMFoundations Attenuverter Assembly guide
GEA
GEA VARIVENT Operating instruction
Walther Systemtechnik
Walther Systemtechnik VMS-05 Assembly instructions
Altronix
Altronix LINQ8PD Installation and programming manual
