Hanna Instruments DiST 3 User manual

DiST®

HI 98300 / 301 / 302

HI 98303 / 304

EC and TDS Testers

with ATC

SPECIFICATIONS

Range / Resolution

DiST®1(HI98300/301) 1999 ppm / 1ppm

DiST®2(HI98302) 10.00 ppt / 0.01ppt

DiST®3(HI98303) 1999 µS/cm / 1µS/cm

DiST®4(HI98304) 19.99 mS/cm / 0.01mS/cm

Accuracy (@20°C/68°F) ±2% f.s.

Typical EMC Deviation ± 1% f.s.

TDS Factor

HI 98300 0.65

HI 98301 / HI 98302 0.5

Calibration Solutions

HI 98300 HI 70442 (1500 ppm)

HI 98301 HI 70032 (1382 ppm)

HI 98302 HI 70038 (6.44 ppt)

HI 98303 HI 70031 (1413 µS/cm)

HI 98304 HI 70039 (5.00 mS/cm) or

HI 70030 (12.88 mS/cm)

Temperature Compensation

Automatic, 0 to 50°C (32 to 122ºF)

Environment 0 to 50°C (32 to 122°F);

RH 95% non-condensing

Battery Type 4 x 1.5V alkaline

Battery Life approx. 200 hours of use

Dimensions 175 x 41 x 23 mm

(6.9 x 1.6 x 0.9")

Weight 95 g (3.4 oz.)

ISTDISTNEW-R5 05/05

WARRANTY

These meters are guaranteed for one year against defects in

workmanship and materials when used for their intended

purpose and maintained according to instructions. Probes

are guaranteed for six months. This warranty is limited to

repair or replacement free of charge. Damages due to acci-

dent, misuse, tampering or lack of prescribed maintenance

are not covered. If service is required, contact the dealer

from whom you purchased the instrument. If under warranty,

report the model number, date of purchase, serial number

and the nature of the failure. If the repair is not covered by

the warranty, you will be notified of the charges incurred. If

the instrument is to be returned to Hanna Instruments, first

obtain a Returned Goods Authorization Number from the

Customer Service department and then send it with ship-

ment costs prepaid. When shipping any instrument, make

sure it is properly packaged for complete protection.

The DiST®models are in compliance with the CE

directives. www.hannainst.com

OPERATION

• Remove the protective cap, turn the

DiST®on, and immerse it into the

solution to be tested, without ex-

ceeding the maximum immersion

level.

• Stir gently and wait for the read-

ing to stabilize. DiST®automati-

cally compensates for temperature

variations.

• The reading on display is directly expressed in:

ppm (mg/L) for DiST®1 (HI 98300 / 301),

ppt (g/L) for DiST®2 (HI 98302), µS/cm for

DiST®3(HI 98303) and mS/cm for DiST®4

(HI 98304).

CALIBRATION

• Immerse the DiST®in the proper calibration

solution (see Specifications table), without ex-

ceeding the maximum immersion level.

• Allow the reading to stabilize and with a

small screwdriver adjust the calibration trim-

mer until the display shows the required solu-

tion value.

For example HI 70032 is

the correct calibration so-

lution for HI 98301, and

the trimmer should be

turned until the display

shows "1382".

PROBE REPLACEMENT

For replacing the probe, contact your Dealer or

the nearest Hanna Service Center.

• Replace the built-in probe with a new:

HI 73301 for DiST®1

HI 73302 for DiST®2

HI 73303 for DiST®3

HI 73304 for DiST®4

BEPS AND BATTERY REPLACEMENT

DiS®T is provided with BEPS (Battery Error Pre-

venting System), which avoids any erroneous

reading due to low battery level, by switching the

meter off.

To replace the batteries, slide off the battery

compartment cover and replace all four 1.5V

batteries while paying attention to their polarity.

Batteries should only be replaced in a non-

hazardous area, and using the battery type

specified in this instruction manual.

ACCESSORIES

HI 70030P 12880 µS/cm calibration solu-

tion, 20 mL sachet, 25 pcs

HI 70031P 1413 µS/cm calibration solution,

20 mL sachet, 25 pcs

HI 70032P 1382 ppm (mg/L) calibration so-

lution, 20 mL sachet, 25 pcs

HI 70038P 6.44 ppt (g/L) calibration solu-

tion, 20 mL sachet, 25 pcs

HI 70039P 5000 µS/cm calibration solution,

20 mL sachet, 25 pcs

HI 70442P 1500 ppm calibration solution,

20 mL sachet, 25 pcs

HI 73301 Spare electrode for DiST®1

HI 73302 Spare electrode for DiST®2

HI 73303 Spare electrode for DiST®3

HI 73304 Spare electrode for DiST®4

HI 731326 Calibration screwdriver (20 pcs.)

DiST is a registered Trademark of

Hanna Instruments

OPERATION

• Remove the protective cap, turn the

DiST®on, and immerse it into the

solution to be tested, without ex-

ceeding the maximum immersion

level.

• Stir gently and wait for the read-

ing to stabilize. DiST®automati-

cally compensates for temperature

variations.

• The reading on display is directly expressed in:

ppm (mg/L) for DiST®1 (HI 98300 / 301),

ppt (g/L) for DiST®2 (HI 98302), µS/cm for

DiST®3(HI 98303) and mS/cm for DiST®4

(HI 98304).

CALIBRATION

• Immerse the DiST®in the proper calibration

solution (see Specifications table), without ex-

ceeding the maximum immersion level.

• Allow the reading to stabilize and with a

small screwdriver adjust the calibration trim-

mer until the display shows the required solu-

tion value.

For example HI 70032 is

the correct calibration so-

lution for HI 98301, and

the trimmer should be

turned until the display

shows "1382".

PROBE REPLACEMENT

For replacing the probe, contact your Dealer or

the nearest Hanna Service Center.

• Replace the built-in probe with a new:

HI 73301 for DiST®1

HI 73302 for DiST®2

HI 73303 for DiST®3

HI 73304 for DiST®4

BEPS AND BATTERY REPLACEMENT

DiS®T is provided with BEPS (Battery Error Pre-

venting System), which avoids any erroneous

reading due to low battery level, by switching the

meter off.

To replace the batteries, slide off the battery

compartment cover and replace all four 1.5V

batteries while paying attention to their polarity.

Batteries should only be replaced in a non-

hazardous area, and using the battery type

specified in this instruction manual.

ACCESSORIES

HI 70030P 12880 µS/cm calibration solu-

tion, 20 mL sachet, 25 pcs

HI 70031P 1413 µS/cm calibration solution,

20 mL sachet, 25 pcs

HI 70032P 1382 ppm (mg/L) calibration so-

lution, 20 mL sachet, 25 pcs

HI 70038P 6.44 ppt (g/L) calibration solu-

tion, 20 mL sachet, 25 pcs

HI 70039P 5000 µS/cm calibration solution,

20 mL sachet, 25 pcs

HI 70442P 1500 ppm calibration solution,

20 mL sachet, 25 pcs

HI 73301 Spare electrode for DiST®1

HI 73302 Spare electrode for DiST®2

HI 73303 Spare electrode for DiST®3

HI 73304 Spare electrode for DiST®4

HI 731326 Calibration screwdriver (20 pcs.)

DiST is a registered Trademark of

Hanna Instruments

DiST®

HI 98300 / 301 / 302

HI 98303 / 304

EC and TDS Testers

with ATC

SPECIFICATIONS

Range / Resolution

DiST®1(HI98300/301) 1999 ppm / 1ppm

DiST®2(HI98302) 10.00 ppt / 0.01ppt

DiST®3(HI98303) 1999 µS/cm / 1µS/cm

DiST®4(HI98304) 19.99 mS/cm / 0.01mS/cm

Accuracy (@20°C/68°F) ±2% f.s.

Typical EMC Deviation ± 1% f.s.

TDS Factor

HI 98300 0.65

HI 98301 / HI 98302 0.5

Calibration Solutions

HI 98300 HI 70442 (1500 ppm)

HI 98301 HI 70032 (1382 ppm)

HI 98302 HI 70038 (6.44 ppt)

HI 98303 HI 70031 (1413 µS/cm)

HI 98304 HI 70039 (5.00 mS/cm) or

HI 70030 (12.88 mS/cm)

Temperature Compensation

Automatic, 0 to 50°C (32 to 122ºF)

Environment 0 to 50°C (32 to 122°F);

RH 95% non-condensing

Battery Type 4 x 1.5V alkaline

Battery Life approx. 200 hours of use

Dimensions 175 x 41 x 23 mm

(6.9 x 1.6 x 0.9")

Weight 95 g (3.4 oz.)

ISTDISTNEW-R5 05/05

WARRANTY

These meters are guaranteed for one year against defects in

workmanship and materials when used for their intended

purpose and maintained according to instructions. Probes

are guaranteed for six months. This warranty is limited to

repair or replacement free of charge. Damages due to acci-

dent, misuse, tampering or lack of prescribed maintenance

are not covered. If service is required, contact the dealer

from whom you purchased the instrument. If under warranty,

report the model number, date of purchase, serial number

and the nature of the failure. If the repair is not covered by

the warranty, you will be notified of the charges incurred. If

the instrument is to be returned to Hanna Instruments, first

obtain a Returned Goods Authorization Number from the

Customer Service department and then send it with ship-

ment costs prepaid. When shipping any instrument, make

sure it is properly packaged for complete protection.

The DiST®models are in compliance with the CE

directives. www.hannainst.com

Other manuals for DiST 3

Table of contents

Other Hanna Instruments Test Equipment manuals

Hanna Instruments

Hanna Instruments HI 38040 User manual

Hanna Instruments

Hanna Instruments HI 38080 User manual

Hanna Instruments

Hanna Instruments PICCOLO 2 HI 98112 User manual

Hanna Instruments

Hanna Instruments DiST 3 User manual

Hanna Instruments

Hanna Instruments Total Chlorine Checker User manual

Hanna Instruments

Hanna Instruments HI981037 User manual

Hanna Instruments

Hanna Instruments Groline HI98118 User manual

Hanna Instruments

Hanna Instruments HI 9811-0 User manual

Hanna Instruments

Hanna Instruments Primo Series User manual

Hanna Instruments

Hanna Instruments HI 98127 User manual

Hanna Instruments

Hanna Instruments HI 95711C User manual

Hanna Instruments

Hanna Instruments HI 3812 User manual

Hanna Instruments

Hanna Instruments HI 99104 User manual

Hanna Instruments

Hanna Instruments HI 7101 User manual

Hanna Instruments

Hanna Instruments HI 98129 User manual

Hanna Instruments

Hanna Instruments UPW HI 98309 User manual

Hanna Instruments

Hanna Instruments HI 95707C User manual

Hanna Instruments

Hanna Instruments 3815 User manual

Hanna Instruments

Hanna Instruments HI 96717C User manual

Hanna Instruments

Hanna Instruments HI 38033 User manual

Hanna Instruments

Hanna Instruments HI 3830 User manual

Hanna Instruments

Hanna Instruments HI 93828 User manual

Hanna Instruments

Hanna Instruments Pool Line HI981204 User manual

Hanna Instruments

Hanna Instruments HI 98121 User manual

Popular Test Equipment manuals by other brands

SMART

SMART KANAAD SBT XTREME 3G Series user manual

Agilent Technologies

Agilent Technologies BERT Serial Getting started

Agilent Technologies

Agilent Technologies N3280A user guide

Vernier

Vernier Go Direct Voltage manual

Lifeloc

Lifeloc R.A.D.A.R. quick start guide

Fluke

Fluke T5-600 Service information

Mercury

Mercury TSL01 user manual

MAHA

MAHA MBT Series Original operating instructions

Fuji Electric

Fuji Electric P-61 instruction manual

ETC

ETC SealerAtor user manual

Skyfine

Skyfine ETHYWAY V2 user manual

Appion

Appion G5 Twin Operation manual

PCB Piezotronics

PCB Piezotronics 8159-0112A Installation and operating manual

BW Technologies

BW Technologies MicroDock II user manual

Sun Nuclear

Sun Nuclear 1027 user guide

Biomark

Biomark HPR LITE READER user manual

Hioki

Hioki 3169-20 instruction manual

Ashcroft

Ashcroft ATE-100 operating manual