LESLIE SWITCH Owner’s Manual
Attaching the CU-1 to the keyboard
ank you and congratulations on your purchase of the Ham-
mond CU-1 Leslie switch. e lever switch on the “Half-
Moon” shaped CU-1 unit is used to control the Leslie eects
just like on the original B-3. Please read the installations in-
structions carefully before you install the CU-1.
Purchased items:
CU-1 unit
(w/2 Thumb screws) ..........1
Spacer (thick) .......................1
Spacer (thin).........................1
Setting up to allow the CU-1
For your safety, please operate your Hammond prod-
uct on a level, stable surface.
Line up the screws attached to the CU-1 unit with the pair of chosen
holes located on the bottom side of the front rail and securely tighten
these screws.
NOTE: Do not place the keyboard with the CU-1 unit attached onto a at
desk type surface. Since the CU-1 extends past the bottom of the
keyboard, the CU-1 unit and front rail of the keyboard could be
seriously damaged.
NOTE: Before placing your XK-3/3C into an ATA keyboard type case, make
sure you remove the CU-1 unit rst.
2. Connecting to the equipment
#920, A-162, A-405, SK2, XK-1C, XK-3, XK-3C, XLK-3
Insert the plug on the CU-1 into the equipment labeled “Foot Switch”
jack.
XK-5, XLK-5
Insert the plug on the CU-1 into the equipment labeled “CU-1” jack.
For other compatible model, see owner’s manual of your instrument
which attach the CU-1 for detail.
#920, A-162, A-405, XK-3, XK-3C, XLK-3
Turn on the equipment, touch the [MENU], [4]Control and choice
the “FOOT SW” page using [PAGE] buttons.
Select “CU-1” using [VALUE] buttons.
SK2, XK-1C
Turn on the equipment, touch the [MENU], [][][]Control and
choice the “FOOT SW” page using [] []buttons.
Select “CU-1” using [VALUE] knob.
XK-5, XLK-5
No operation required.
For other compatible model, see owner’s manual of your equipment
how to set up the CU-1.
Playing with your CU-1 Switch
#920, A-162, A-405, XK-3, XK-3C
CHORALE: e Leslie eect is “On”, rotation mode is “Slow.”
TREMOLO: e Leslie eect is “On”, rotation mode is “Fast.”
STOP: 1) e rotation stops, the Leslie eect is still “ON”, if the
[BRAKE] button is “On” (XK-3/3C) or O Mode is at “Brake”
(#920, A-162, A-405).
2) e Leslie eect is “O ”, rotation continues, if the [BRAKE]
button is “O ” (XK-3/3C) or O Mode is at “rough” (#920,
A-162, A-405).
It takes a moment for the equipment detecting STOP position,
to make the switching between CHORALE and TREMOLO
smoothly.
SK2, XK-1C, XK-5
CHORALE: e rotation mode is “Slow.”
TREMOLO: e rotation mode is “Fast.”
STOP: e rotation stops. It takes a moment for the equipment de-
tecting the STOP position, to make the switching between
CHORALE and TREMOLO smoothly.
It switches only the rotation. To switch “On” or “Bypass” the
Leslie eect (switch Rotary or Stationary channel), press the
[BYPASS] button.
NOTE: On newer Hammond products, the speeds of the Leslie can also
be selected by means of a kick switch on the expression pedal or a
switch button on the product itself. Thus the selected speed on the
CU-1 unit may occasionally not match the action speed (slow-fast-
o) of the Leslie. If this occurs, simply move the lever switch on the
CU-1 to the adjacent position and the actual rotor speed will then
match the CU-1 selection.
Manufacturer:
SUZUKI MUSICAL INSTRUMENT MFG. CO., LTD.
25-12, Ryoke 2 Chome, Naka-ku,
Hamamatsu 430-0852 (Shizuoka)
JAPAN
1. Attaching the CU-1 unit.
SK2, XK-1C, XK-3, XK-3C (Thin bottom of the Keyboard)
Remove the protective paper from the adhesive tape on the thick spac-
er, and attach the spacer to the CU-1 unit as shown above.
XLK-3, XLK-5 (Middle bottom of the Keyboard)
Remove the protective paper from the adhesive tape on the thin spac-
er, and attach the spacer to the CU-1 unit as shown above.
#920, A-162, A-405, XK-5 (Deep bottom of the Keyboard)
No spacer is needed for mounting the CU-1 Unit.
