Hamilton Manufacturing Corporation Token Vendor Quick start guide
Document#101-0163 1 1/10/06
Operational Manual
for the
Token Vendor
Document#101-0163 2 1/10/06
ABOUT THIS MANUAL
ThismanualwasdesignedtointroducetheTokenVendorandtoprovideinstructionsonhowtoinstallthe
machines.Thismanualwill enabletheoperator toprogrampayouts intheAutocashier.
Iffurtherassistanceisneeded,pleasecallthemanufacturerat(800)837-5561or (419)867-4858.
Whencallingforassistanceitisveryimportant to have the serial numbersreadilyavailable. Pleaserecord
thesenumbersinthe spacesprovided.
TOKEN VENDOR SERIAL #___________________________________________
HOPPER SERIAL #_____________________________________
KEY / LOCK #______________________________________________
Pleasecompletethe warrantycard,which wasincludedwith yourmachine,andreturnittothemanufacturer.
Document#101-0163 3 1/10/06
TABLE OF CONTENTS
I. INTRODUCTION...................................................................................................4
II. SPECIFICATIONS ...............................................................................................5
III. INSTALLATION ..................................................................................................6
Unpacking ...................................................................................................................................... 7
BASE .............................................................................................................................................. 8
SITE ............................................................................................................................................... 8
TokenVendor................................................................................................................................. 9
ACWG/LRetrofit ....................................................................................................................... 11
IV. VERSION REQUIREMENTS FOR GL-ACW..............................................12
V. BACKUP................................................................................................................13
VI. CHIP REPLACEMENT IN THE GL-ACW...................................................15
Removal ....................................................................................................................................... 15
Installation ................................................................................................................................... 15
VII. RESTORE .........................................................................................................16
VIII PROGRAMMING............................................................................................18
IX OPERATION .......................................................................................................19
Document#101-0163 4 1/10/06
I. INTRODUCTION
TheHamiltonTokenVendor is acompactunit,designedto work with theACWG/L,todispensea token or
multipletokenswhen aselectionismade.Theunitcan holdapproximately1200quartersizetokens.
WARNING – If the Autocashier is programmed to dispense promotional tokens
and the Token Dispenser and its interface harness are not properly installed the
machine will dispense coins from the change hopper instead of tokens. If you wish
to disconnect the Token Dispenser for any length of time be sure to program each
wash to dispense zero (0) tokens.
Document#101-0163 5 1/10/06
II. SPECIFICATIONS
TheHamiltonTokenVendorisintended tobewired throughconduittotheACWG/L.Themachineoperates
on120Vacsuppliedbythe GoldLinedistributionpanel (#5).
CABINETDIMENSIONS:
Ø.88
Ø.38
( 4 PLCS )
10.00
3.88
1.37 3.63
7.25
9.00
2.63
1.75
5.90
20.00
13.00
Document#101-0163 6 1/10/06
III. INSTALLATION
WhenInstallingtheHamiltonTokenVendoryouwillneedtorun6wiresfromtotheACWG/LtotheHamilton
Token Vendor,ratedatleast18Gage.
Recommendedwirecolors are:
Black - Hot
White-Neutral
Green-Ground
Red - Hopper
Red/White-Drop
Purple-HopperReturn
Itisalso recommendedthattheyarerunusingconduit.
Consultlocalcodesbeforeinstalling.
RUN 6 WIRES BETWEEN
ACW AND TOKEN VENDOR
Document#101-0163 7 1/10/06
Unpacking
Thereareanumberof pointstokeepinmindwhileunpackingyourHamiltonTokenVendor.Theseitemswill
maketheinstallation andcontinuedoperation ofyourmachine runsmoother.Thesetipsare listedbelow.
Be sure to save your key
Thekey is placed inside a small cloth bag and attached to the outside ofthemachine.Whenremovingthe
shrink-wrap, be sure to locate the bag containing the key and set it aside so it does not get thrown away.
NOTE:MAKEAPERMANENTRECORDOFTHENUMBERONYOURKEYINCASEKEYIS
LOSTAND MUST BE REORDERED.
Remove the packing strap from the hopper
The hopper comes shipped with a packing strap secured around it to minimize the vibrations caused by
shipping.Ifthis strapisnot removed,thehopperwillnottipoutforeasyfilling. Thestrapmay becutoffwith
a pair of wire cutters or sturdy scissors. Cardboard is placed around the edges of the hopper to protect it
duringshipping.If strappingwillnotpull outfrombeneathhopper plate thenloosenthe3 #1/4nutsholding
plateandtryagain.Oncestrappingisout,tightenthe3#1/4nuts.Thenbesuretoremovethe cardboard as
well.
Remove all packing debris from hopper
Duringunpacking,ensurethatdebrisdoesnotfallintohopperbowl.If thismaterialisnotremoved,thehopper
couldjam.Withthepowercompletely disconnected,removeallloose materialinsidethe hopperbowl.
Document#101-0163 8 1/10/06
BASE
When installing the base it is important to pick the correct base for the location. Use the picture below to
decideonbestbaseforyour location.
28.15
31.96 37.96
17.08 16.933.00
42.25
46.06
52.06
22.25
26.06
32.06
Ø.80
( 4 PLCS )
Ø.80
( 4 PLCS )
9.25
12.25
12.25 9.25
1.50
1.50
6.25
9.25
1.50 6.25 9.251.50
2.63 4.00
4.004.13
4.13
4.00
2.63
4.00 4.00
2.63
4.13 4.00
1.50 9.25
6.25
1.50
9.25
12.25
Ø.80
( 4 PLCS )
100-0113 TOKEN VENDOR BASE
MOUNTING PLATE
61-0600A MPU SHORT ANGLED BASE
MOUNTING PLATE
61-0601A MPU TALL ANGLED BASE
MOUNTING PLATE
SITE
To prepare the site, Hamilton recommends the placing of four anchoring bolts into the concrete with the
threadsextendingatleast1¼”abovethesurface.Usethepreviousdiagramstodeterminetheplacementofthe
bolts.Pleasefollow allapplicablelocalcodes.
Itisalsorecommendedthatthewiring berunthroughtheconcreteandupthroughthecenterofthebase,using
flexibleconduit.
Document#101-0163 9 1/10/06
Token Vendor
Installation
1. Make surethereisnopowerin the sixwiresruntothe HamiltonTokenVendor.
2. Open up cabinetandunplugandremovehopper and set aside.
3. Using aPhillipsheadscrewdriver,anda 7/16" socketwrenchremovefour #1/4-20 nuts
lockwashersandscrews,(these#1/4nuts, lockwashers and screwsareusedforshippingpurposes
only)thiswillallowyoutoremovethehopperplate.
4. Place cabinetonbaseandrun wiresupthroughconduit holeinbottomofcabinet.
5. Connect wirestoDualTerminal stripasshownon diagram.(page9)
Note:Forproperwireconnectionsconsultacertifiedelectrician.
6. Place hopper platebackinpositionandtighten to base usingfour#5/16-18screws,with ¼” hex
key. (page 10)
7. Replace hopperinmachineand pluginthehopper.
L1WHITE
WHITE/RED
HOPPERRED
10
9
8
7
6
1
2
3
4
5
TO HOPPER
DROP
PURPLE HOPPER RETURN
GREEN GROUND
BLACK L2
10
9
8
7
6
1
2
3
4
5
WHITE/RED
RED
PURPLE
WHITE
GREEN
BLACK
DROP
HOPPER
HOPPER RETURN
L1
GROUND
L2
FROM ACW
TERMINAL STRIP
Document#101-0163 10 1/10/06
Table of contents
Popular Vending Machine manuals by other brands
Azkoyen
Azkoyen Zensia technical information
Azkoyen
Azkoyen STEP 74 technical information
SandenVendo
SandenVendo Snack Safety Point SVE SSP Programming manual
Intralot
Intralot Dreamtouch Smart manual
Westomatic
Westomatic Primo Compact Cleaning manual
Crane
Crane Dixie-Narco Glassfront BevMax 3 5800 Installation & setup guide