Haiku K3150-S1 User manual
Installation Guide
www.haikufan.com
©2013 Delta T Corporation
S1
Model Number: K3150-S1
S3150-S1
May be protected by one or more of the following patents:
Australian Registered Design No. 325331, 328015; U.S. Pat. Nos. D612476 and D614757; Malaysian Registered Design
No. MY09-00255-0101, MY09-00973-0101; and Singapore Registered Design No. D2008/951/E and D2009/235/G.
Haiku and the Haiku logo are trademarks of Delta T Corporation, registered in the United States and/or other
countries.
Thank you for buying the world’s most innovative fan. Please take a few moments to register your
fan with us online at www.haikufan.com/warrantyregistration.
Installation Guide:
April 2013
Rev. J
This product is sold by a plant whose
Management System is certified as
being in conformity with ISO 9001:2008.
This device complies with Part 15 of
the FCC Rules. This device complies
with Canada ICES-003, Class B.
4004784
4004783
Conforms to ANSI/UL STD 507–Electric Fans
Certified to CAN/CSA C22.2 No. 113–Fans & Ventilators
HAIKU® by Big Ass Fans i
INTRODUCTION
1About Haiku
Technical specifications
2Parts & hardware
Fan diagram
PREPARATION
3
Unpacking your fan
Determining fan location
Tools needed
INSTALLATION
4Installing the airfoils
5Installing the lower cover
Installing rubber bumpers
6Attaching the mounting plate
Securing the safety cable
7
Wiring the fan
Hanging the fan
Securing the wiring cover
8Wire color chart
Wiring diagram
OPERATION
9
Powering the fan
Replacing remote battery
Changing fan speed
Sleep mode
Timer mode
Whoosh mode
10 Fan mode indicators
Contents
TROUBLESHOOTING
11 General troubleshooting
MAINTENANCE
12 Annual maintenance
©2013 DELTA T CORP. ALL RIGHTS RESERVED.
ii
IMPORTANT SAFETY INSTRUCTIONS
Read and save these instructions prior to installing and operating your Haiku. Retain
this installation guide for maintenance and troubleshooting information. If you have
further questions, contact Haiku Customer Service at www.haikufan.com/service.
WARNING: To reduce the risk of fire, electric shock, and serious bodily injury to persons, observe the
following:
• Installation work and electrical wiring must be done by qualified person(s) in accordance with all
applicable codes and standards.
• When cutting or drilling into ceiling, do not damage electrical wiring and other hidden utilities.
• Use this fan only in the manner intended by the manufacturer.
CAUTION: The installation of this fan must be in accordance with the requirements specified in this
installation manual and with any additional requirements set forth by the national electrical code (NEC),
ANSI/NFPA 70-2008, and all local codes. Code compliance is ultimately YOUR responsibility!
WARNING: If installing the fan in Australia, a licensed electrician must perform the electrical installation.
CAUTION: Exercise caution and common sense when powering the fan. Do not connect the fan to a
damaged power source. Do not attempt to resolve electrical malfunctions or failures on your own.
WARNING: The fan must be used with the supplied remote control. Other parts cannot be substituted.
CAUTION: When service or replacement of a component in the fan requires the removal or
disconnection of a safety device, the safety device must be reinstalled or remounted as previously
installed.
WARNING: Power must be disconnected before installation and servicing, cleaning, and other user-
maintenance. Failure to disconnect power creates risk of fire, electric shock, and serious bodily injury.
CAUTION: The product warranty will not cover equipment damage or failure that is caused by
improper installation or operation.
CAUTION: The fan must be mounted a minimum of 2.4 m from the floor and 1 m from the nearest wall.
The ceiling should be stable with no shaking, high vibrations or heavy impacts.
WARNING: Do not install the fan in an environment that is excessively dusty, conductive, corrosive, or
gas-filled, is exposed to open flames (e.g., gas-burning stoves), is near strong chemicals or solvents, or
where there is excessive heat, shock, or vibration.
WARNING: Do not bend the airfoils when installing or servicing the fan. Do not insert foreign objects in
between the rotating fan airfoils.
CAUTION: This fan is not intended for use by persons (including children) with reduced physical,
sensory, or mental capabilities, or lack of experience and knowledge, unless they have been given
supervision or instruction concerning the use of the fan by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the fan.
WARNING: Before installing or servicing the fan, ensure power is disconnected.
CAUTION: Haiku (K3150-S1) is rated for use in damp environments and can be operated indoors or
outdoors. Haiku Bamboo (S3150-S1) is not rated for damp environments and must be operated indoors
only.
CAUTION: The fan will begin rotating when power is applied.
HAIKU® by Big Ass Fans 1
HAIKU
®
by Big
Ass
Fans
1
Thank you for your Haiku purchase and congratulations on your selection of an elegant, ecient, and
cost-eective way to stay cool! We are proud to assure you that the fan you have chosen is backed
by extensive research, thorough testing, and quality manufacturing.
If you have any questions or comments, please contact Customer Service by visiting our Web site at
www.haikufan.com/service.
About Haiku®
Haiku products are inspired by the seamless integration of natural forms and materials with the latest
technologies. Haiku fans consume up to 80% less energy than traditional ceiling fans and maximize
the sustainable use of global resources so you can now help save the planet in STYLE. Backed by the
engineering resources of Big Ass Fans, the fan of choice for smaller spaces that need extraordinary
air movement is crystal clear—it’s Haiku.
Technical specifications
Before assembling and installing your fan, review the technical specifications in the table below. A fan
diagram and parts list can be found on the following page.
Model Haiku® / Haiku® Bamboo
Model number K3150-S1 / S3150-S1
Fan diameter 1.5 m
Number of airfoils 3
Weight 6 kg
Number of fan speeds 6
Operating voltage 220–240VAC 1Φ
Operating frequency 50 Hz
Full load amps 0.363A
Wattage Max: 25 Watts
Min: 4 Watts
Ambient operational temperature range 0–40° C
Operational humidity range 20–90% non-condensing
Status indication LED display
Introduction
©2013 DELTA T CORP. ALL RIGHTS RESERVED.
2
Haiku Bamboo
Haiku
Haiku Bamboo
Haiku
Parts and hardware
If you are missing any parts or hardware required for the installation or operation of your Haiku, contact
Haiku Technical Service. Note: Drawings below are not to scale.
or
Mounting plate (2) Rubber
bumper
(2) Mounting
bracket
Lower cover
(Haiku)
Lower cover
(Bamboo)
or
(3) Airfoil (Haiku) (3) Airfoil
(Bamboo) Motor hub Remote control*
(4) 6 mm Flat
washer
(4) 6 mm
Nylock nut
Safety cable
shackle*
(2) Extension
tube screw cap
(6) M5 Airfoil
screw
(6) M5 Airfoil
screw (Bamboo)
(6) 5 mm Lock
washer
*Safety cable is not shown in diagram.
INTRODUCTION CONT.
1234
56
7
Mounting
hardware
Airfoil
hardware
8
8
7
5
4
2
1
3
8
6
Note: Haiku and Haiku Bamboo include dierent airfoils
and airfoil hardware. Refer to the parts list for details.
HAIKU® by Big Ass Fans 3
2.4 m Min.
to Floor
1 m Min. to
Obstruction
No
Obstructions
Before assembling and operating your fan, review the following tips and guidelines to ensure a safe
and easy installation, particularly the safety guidelines on page ii. If you have questions about any
aspect of the installation process, consult a structural engineer or electrical contractor or contact
Haiku Technical Service.
Unpacking the fan
As you remove the fan from its packaging, make sure you are not missing any components required
for assembly and operation. Refer to the fan diagram and the Parts and Hardware section for a list of
components. If you are missing a part required for installation, contact Haiku Technical Service.
If you ordered multiple fans, be sure to keep the components of each fan together! Certain
fan components are not interchangeable.
Determining fan location
Consider the following guidelines as you decide where to install your Haiku:
• Do not mount the fan in an environment that is excessively dusty, conductive, corrosive, or gas-filled,
near strong chemicals or solvents, or where there is excessive heat, shock, or vibration.
• Do not install the fan near open flames such as those from a gas stove.
• The ceiling should be stable with no high vibrations, shaking, or heavy impacts.
• Install the fan so that the airfoils are at least 2.4 m above the floor.
• Make sure the space around the fan has a clearance of at least 1 m from obstructions such as
cabinets, doors, lighting fixtures, etc.
• Make sure the space between the fan and ceiling is clear of any obstructions.
• Install the fan on a switched circuit so that you can turn o the fan using a wall switch in addition to
using the remote control.
If you ordered multiple fans, be sure to keep the components of each fan together! Certain
fan components are not interchangeable.
!
Preparation
Tools needed
You will need the following tools to install the fan:
• Ladder
• Hex key (provided)
• Wire stripper
• Adjustable wrench
• #1 Phillips screwdriver
©2013 DELTA T CORP. ALL RIGHTS RESERVED.
4
Review the safety guidelines. If you are not completely comfortable or have questions about any
aspect of the installation process, consult a structural engineer or electrical contractor or contact Haiku
Technical Service for assistance.
Step 1. Installing the airfoils
Position the fan upside-down. Moving clockwise around the fan, align each airfoil with a fan hub tab
and firmly press it into place. Make sure that the colored stickers match the colors of the stickers on the
attachment of the fan hub. Loosely secure the airfoils with the provided (6) airfoil screws. Once the
airfoils are in position, fully tighten the screws to secure the airfoils to the fan hub.
Visit www.haikufan.com to view installation videos illustrating the airfoil installation process.
Be careful not to damage the circuit board while installing airfoils!
Installation
airfoils are in position, fully tighten the screws to secure the airfoils to the fan hub.
Visit www.haikufan.com to view installation videos illustrating the airfoil installation process.
tip!
tip!
Haiku®
To ease airfoil installation, the (3) motor top screws can be loosened. Do not forget to retighten them!
!
Haiku® Bamboo
When installing the Bamboo airfoils,
the edge of each airfoil should tuck
under the airfoil next to it.
Be careful not to damage the circuit board while installing airfoils!
Be careful not to damage the circuit board while installing airfoils!
!
Motor
top screw
HAIKU® by Big Ass Fans 5
For Haiku, position the lower cover, and then place both hands flat on the cover and turn clockwise to lock
the lower cover into place.
Step 2. Installing the lower cover
With the fan still positioned upside-down, remove the protective covering from the circuit board. With
the fan still in the upside-down position, align the three tabs on the lower cover with the three slots in
the undersides of the airfoils and secure.
INSTALLATION CONT.
Haiku Bamboo
For Haiku Bamboo, simply snap the lower cover to the bottom of the fan hub.
Lower
Cover
Haiku
Step 3. Installing rubber bumpers
Slide the rubber bumpers on the extension tube brackets as shown on the right.
Rubber
bumper
Lower
Cover
©2013 DELTA T CORP. ALL RIGHTS RESERVED.
6
Step 4. Installing anchor bolts
Ensure wiring has been routed to the fan site. Drill four 8 mm holes. The hole depth should not
exceed 40 mm.
Drill one 14 mm hole (for safety anchor hook) in the pattern shown below. The hole depth should not
exceed 50 mm.
Remove any dust from the holes. Insert the (4) anchor bolts and (1) anchor hook into the pre-drilled
holes. Strike the heads of the anchor bolts with a hammer, ensuring the bolt sleeves are flush with the
ceiling surface. Make sure the anchor hook is fully tightenend.
INSTALLATION CONT.
Step 5. Securing the mounting plate
Position the mounting plate on the (4) anchor bolts. Ensure
all anchor bolts are fully tightened to expand and lock the
anchors.
40 mm
80 mm
100 mm
8 mm
(Anchor Bolt)
14 mm
(Anchor Hook)
ceiling surface. Make sure the anchor hook is fully tightenend.
Concrete Ceiling
40 mm
Max
Anchor Bolt
Anchor Hook
50 mm
Max
Step 6. Securing the safety cable
Attach one mounting bracket to the mounting plate, but do
not fully tighten. Raise the fan to the mounting bracket and
temporarily rest one rubber bumper in the space between
the bracket and plate to help support the fan while
securing the safety cable with the shackle.
Safety
cable Mounting
bracket
Other manuals for K3150-S1
1
This manual suits for next models
1
Table of contents
Other Haiku Fan manuals
Popular Fan manuals by other brands
ELTA FANS
ELTA FANS H03VV-F installation guide
Hunter
Hunter 20714 Owner's guide and installation manual
Emerson
Emerson CARRERA VERANDA CF542ORB00 owner's manual
Hunter
Hunter Caraway Owner's guide and installation manual
Panasonic
Panasonic FV-15NLFS1 Service manual
Kompernass
Kompernass KH 1150 operating instructions
