H3C S7502 User manual
Installation Manual
H3C S7502 Ethernet Switch Table of Contents
i
Table of Contents
Appendix A Installation of Lightning Arrester for AC Power (Lightning Protection Grounding
Strip) ...............................................................................................................................................A-1
Installation Manual
H3C S7502 Ethernet Switch Appendix A Installation of Lightning Arrester for AC Power
(Lightning Protection Grounding Strip)
A-1
Appendix A Installation of Lightning Arrester for
AC Power (Lightning Protection Grounding Strip)
Caution:
No lightning arrester is shipped with the switch. You should purchase a lightning
arrester if needed.
If an outdoor AC power cable should be directly led to the switch, please serially
connect the lightning arrester for AC power (lightning protection grounding strip) before
you plug AC power cable into the switch, thus to prevent the possible damage to the
switch due to lightning strike. You can use cable clips and screws to fasten the lightning
arrester for AC power on the cabinet, workbench or the wall of equipment room.
Mainboard
Grounding and polarity indicator (red) :
On means that the lines are wrongly connected
Please check the power supply circuit.
Power switch
Normal operation indicator (green):
On means that the arrester works normally.
Otherwise, the protection circuit has
been damaged
.
Multipurpose power socket, connected to the device
protected by the arrester
Power socket (complied with IEC standard),
connected to the power supply of
the equipment room through power cord
Overload auto protector,
which can be manually reset.
Mainboard
(either the grounding cable is not well connected, or the live and zero lines are wrongly connected)
.
Figure A-1 Diagram of lightning arrester
Installation Manual
H3C S7502 Ethernet Switch Appendix A Installation of Lightning Arrester for AC Power
(Lightning Protection Grounding Strip)
A-2
Caution:
zMake sure that the arrester is well grounded before using the lightning arrester for
power.
zAfter inserting AC power cable connector of switch into the socket of lightning
arrester, if the green LED is on and the red LED does not alarm, the lightning
arrester of power is running and the function of lightning protection has taken effect.
zPay adequate attention if the red LED ison. You should correctly locate the problem,
whether it is caused because the grounding cable of the arrester is not well
grounded or because the live and zero wires are connected in reverse direction.
You may check that in the following way. When the red LED is on, use a multimeter
to examine polarity at the power socket of the arrester. If it is same to that of the
power socket in the equipment room, it means that arrester is not well grounded. If it
is adverse to that of the power socket in the equipment room, it means that the
power socket of the arrester is set to the reverse polarity. In this case, you should
open the power socket of arrester to correct polarity. After that, if the red LED still
alarms, it means that the arrester is not well grounded yet.
Other manuals for S7502
7
Table of contents
Other H3C Switch manuals
H3C
H3C FS5300-EI Series Instruction Manual
H3C
H3C S5120-EI Series Installation manual
H3C
H3C S7500E-XS Series Installation manual
H3C
H3C S12500CR Series User manual
H3C
H3C S12500-X Parts list manual
H3C
H3C S12500-X User manual
H3C
H3C S9500 Series User manual
H3C
H3C S3100-52P User manual
H3C
H3C S6850 Series User manual
H3C
H3C S3610- 28P User manual
H3C
H3C S5130S-EI series Owner's manual
H3C
H3C S3610 Series User manual
H3C
H3C H3C S7500E Series User manual
H3C
H3C S12500 Series User manual
H3C
H3C S9500 Series User manual
H3C
H3C S12500-XS Series Operating and maintenance manual
H3C
H3C S6520X-EI Series User manual
H3C
H3C S7500 Series User manual
H3C
H3C S5500-28C-EI User manual
H3C
H3C S12500 Series Quick start guide
