GW Instek PEL-3021 User manual

DC Electronic Load

PEL-3000 Series

USER MANUAL

VERSION: 2.00

ISO-9001 CERTIFIED MANUFACTURER

This manual contains proprietary information, which is protected by

photocopied, reproduced or translated to another language without

prior written consent of Good Will company.

The information in this manual was correct at the time of printing.

However, Good Will continues to improve products and reserves the

rights to change specification, equipment, and maintenance

procedures at any time without notice.

Good Will Instrument Co., Ltd.

No. 7-1, Jhongsing Rd., Tucheng Dist., New Taipei City 236, Taiwan.

Table of Contents

SAFETY INSTRUCTIONS .................................................. 3

GETTING STARTED.......................................................... 8

PEL-3000 Series Introduction ............... 10

Accessories.......................................... 12

Appearance .......................................... 15

First Time Use Instructions ................. 24

OPERATION .................................................................. 50

Basic Operation ................................... 52

Basic Configuration ............................. 65

Advanced Configuration Settings ......... 72

Step Resolution Configuration ............. 79

Protection Settings .............................. 82

System Settings ................................... 90

Go-NoGo ............................................. 94

Save Recall........................................... 97

FUNCTION MENU ........................................................111

Function Menu Overview ................... 112

Program............................................. 118

Sequence ........................................... 126

OCP Test Automation ........................ 145

OPP Test Automation......................... 151

BATT Test Automation ....................... 157

EXTERNAL CONTROL ...................................................165

Analog Control................................... 166

Parallel Operation.............................. 184

REMOTE CONTROL ......................................................191

PEL-3000 User Manual

Interface Configuration ...................... 192

FAQ..............................................................................203

APPENDIX ....................................................................205

Replacing the Dust Filter ................... 207

Replace the Clock Battery ................... 208

GPIB Installation ............................... 209

PEL-3000 Default Settings .................. 210

Frame Control Connector Contacts .... 213

Operating Mode Description.............. 218

Operating Area .................................. 223

PEL-3000 Specifications ..................... 227

PEL-3000 Dimensions ........................ 239

Declaration of Conformity .................. 242

INDEX ..........................................................................243

SAFETY INSTRUCTIONS

This chapter contains important safety

instructions that you must follow during

operation and storage. Read the following before

any operation to insure your safety and to keep

the instrument in the best possible condition.

Safety Symbols

These safety symbols may appear in this manual or on the

instrument.

WARNING

Warning: Identifies conditions or practices that

could result in injury or loss of life.

CAUTION

Caution: Identifies conditions or practices that

could result in damage to the instrument or to

other properties.

DANGER High Voltage

Attention Refer to the Manual

Earth (ground) Terminal

Frame or Chassis Terminal

Do not dispose electronic equipment as unsorted

municipal waste. Please use a separate collection

facility or contact the supplier from which this

instrument was purchased.

PEL-3000 User Manual

Safety Guidelines

General

Guideline

CAUTION

Do not place any heavy object on the

instrument. Note: Only 2 units can be stacked

vertically.

Avoid severe impact or rough handling that

leads to damaging the instrument.

Do not discharge static electricity to the

instrument.

Use only crimped wires, not bare wires, for the

terminals.

Do not block the cooling fan opening.

Do not disassemble the instrument unless you

are qualified.

The equipment is not for measurements

performed for CAT II, III and IV.

(Measurement categories) EN 61010-1:2010 specifies the

measurement categories and their requirements as follows. The

instrument falls under category II.

Measurement category IV is for measurement

performed at the source of low-voltage

installation.

Measurement category III is for measurement

performed in the building installation.

Measurement category II is for measurement

performed on the circuits directly connected to

the low voltage installation.

0 is for measurements performed on circuits not

directly connected to Mains.

SAFETY INSTRUCTIONS

Power Supply

WARNING

AC Input voltage range: 100-120VAC/200-

240VAC

(90-132VAC/180-250VAC)

Frequency: 47-63Hz

Power:

PEL-3021: 90VA Max

PEL-3041: 110VA Max

PEL-3111: 190VA Max

PEL-3211: 230VA Max

To avoid electrical shock connect the protective

grounding conductor of the AC power cord to

an earth ground.

Cleaning

Disconnect the power cord before cleaning.

Use a soft cloth dampened in a solution of mild

detergent and water. Do not spray any liquid.

Do not use chemicals containing harsh material

such as benzene, toluene, xylene, and acetone.

Operation

Environment

Location: Indoor, no direct sunlight, dust free,

almost non-conductive pollution (Note below)

Temperature: 0°C to 40°C

Humidity: 0 to 85% RH

Altitude: <2000m

PEL-3000 User Manual

(Pollution Degree) EN 61010-1:2010 specifies the pollution degrees

and their requirements as follows. The instrument falls under

degree 2.

Pollution refers to “addition of foreign matter, solid, liquid, or

gaseous (ionized gases), that may produce a reduction of dielectric

strength or surface resistivity”.

Pollution degree 1: No pollution or only dry,

non-conductive pollution occurs. The pollution

has no influence.

Pollution degree 2: Normally only non-

conductive pollution occurs. Occasionally,

however, a temporary conductivity caused by

condensation must be expected.

Pollution degree 3: Conductive pollution occurs,

or dry, non-conductive pollution occurs which

becomes conductive due to condensation which

is expected. In such conditions, equipment is

normally protected against exposure to direct

sunlight, precipitation, and full wind pressure,

but neither temperature nor humidity is

controlled.

Storage

environment

Location: Indoor

Temperature: -20°C to 70°C

Humidity: <90% RH

Disposal

Do not dispose this instrument as unsorted

municipal waste. Please use a separate collection

facility or contact the supplier from which this

instrument was purchased. Please make sure

discarded electrical waste is properly recycled to

reduce environmental impact.

SAFETY INSTRUCTIONS

Power cord for the United Kingdom

When using the instrument in the United Kingdom, make sure the

power cord meets the following safety instructions.

NOTE: This lead/appliance must only be wired by competent persons

WARNING: THIS APPLIANCE MUST BE EARTHED

IMPORTANT: The wires in this lead are coloured in accordance with the

following code:

Green/ Yellow:

Earth

Blue:

Neutral

Brown:

Live (Phase)

As the colours of the wires in main leads may not correspond with

the coloured marking identified in your plug/appliance, proceed

as follows:

The wire which is coloured Green & Yellow must be connected to

the Earth terminal marked with either the letter E, the earth symbol

or coloured Green/Green & Yellow.

The wire which is coloured Blue must be connected to the terminal

which is marked with the letter N or coloured Blue or Black.

The wire which is coloured Brown must be connected to the

terminal marked with the letter L or P or coloured Brown or Red.

If in doubt, consult the instructions provided with the equipment

or contact the supplier.

This cable/appliance should be protected by a suitably rated and

approved HBC mains fuse: refer to the rating information on the

equipment and/or user instructions for details. As a guide, a cable

of 0.75mm2should be protected by a 3A or 5A fuse. Larger

conductors would normally require 13A types, depending on the

connection method used.

Any exposed wiring from a cable, plug or connection that is

engaged in a live socket is extremely hazardous. If a cable or plug is

deemed hazardous, turn off the mains power and remove the cable,

any fuses and fuse assemblies. All hazardous wiring must be

immediately destroyed and replaced in accordance to the above

standard.

PEL-3000 User Manual

GETTING STARTED

This chapter provides a brief overview of the

PEL-3000, the package contents, instructions for

first time use and an introduction to the front

panel, rear panel and GUI.

PEL-3000 Series Introduction................................... 10

Model Line Up .................................................................................10

Main Features ...................................................................................11

Accessories.............................................................. 12

Package Contents .............................................................................14

Appearance.............................................................. 15

PEL-3000 Front Panel ....................................................................15

(PEL-3021/PEL-3041).............................................................15

(PEL-3111) .................................................................................15

(PEL-3211 Booster Pack) ........................................................16

Rear Panel..........................................................................................20

PEL-3021 / PEL-3041.............................................................20

(PEL-3111) .................................................................................20

(PEL-3211 Booster Pack) ........................................................21

Display ...............................................................................................23

First Time Use Instructions ..................................... 24

This manual suits for next models

Table of contents

Other GW Instek Power Supply manuals

GW Instek

GW Instek PSB-1400M User manual

GW Instek

GW Instek GPE-1326 Series User manual

GW Instek

GW Instek PSP-603 User manual

GW Instek

GW Instek PSW Series Owner's manual

GW Instek

GW Instek PSP-603 User manual

GW Instek

GW Instek PSW-Multi Series User manual

GW Instek

GW Instek ASD Series User manual

GW Instek

GW Instek Tequipment PEL-3000 Owner's manual

GW Instek

GW Instek GPE-1326 Series User manual

GW Instek

GW Instek PSW Series User manual

GW Instek

GW Instek PSH series User manual

GW Instek

GW Instek PSU Series User manual

GW Instek

GW Instek GPP-3610H User manual

GW Instek

GW Instek ASD Series User manual

GW Instek

GW Instek PSB-2000 series User manual

GW Instek

GW Instek PSH series User manual

GW Instek

GW Instek PEL-3000AH Series User manual

GW Instek

GW Instek PPH-1503 User manual

GW Instek

GW Instek GPD-303S Series User manual

GW Instek

GW Instek PSU Series Owner's manual

GW Instek

GW Instek GPS-2303 User manual

GW Instek

GW Instek PSU Series User manual

GW Instek

GW Instek PSU Series Owner's manual

GW Instek

GW Instek PEL-500 Series User manual

Popular Power Supply manuals by other brands

Monacor

Monacor PS-12CCD instruction manual

VOLTIMA

VOLTIMA MagicBox 15 Installation and operating instructions

Agilent Technologies

Agilent Technologies 6032A Service manual

Miller

Miller Auto Deltaweld 452 owner's manual

BCP

BCP PUOUBK How to install

HC 2210 manual

Puls

Puls CT5.241 installation manual

OCZ

OCZ ZX1250W Technical specifications

iseg

iseg ECH 238 manual

Power

Power XXL A Series instruction manual

Agilent Technologies

Agilent Technologies 6631B Service manual

Renogy

Renogy PHOENIX 300 user guide

HP 6200B Operating and service manual

Epson

Epson Stylus Scan 2500 Product information sheet

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 manual

Puls

Puls MiniLine ML50.100 instruction manual

Puls

Puls AS-Interface SLA4.100 installation manual

Kenwood

Kenwood PS-60 instruction manual