GVI Security GV-FXDVFA28 User manual
Operating Instructions
Before installing and using the camera,
please read these instructions thorough-
ly and retain them for later reference.
GV-FXDVFA28 GV-FXDVFA40
GV-FXDVFA28P GV-FXDVFA40P
Regulatory Notices For U.S.A
This equipment has been tested and found
to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide
reasonable protection against harmful inter-
ference in a residential installation! This
equipment generates, uses and can radiate
radio frequency energy and, if not installed
and used in accordance with the instruc-
tions, may cause harmful interference to
radio communications.
However, there is no guarantee that interfer-
ence will not occur in a particular installation.
If this equipment does cause harmful inter-
ference to radio or television reception,
which can be determined by turning the
equipment off and on, the user is encour-
aged to try to correct the interference by one
or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the
equipment and receiver.
•Connect the equipment into an outlet on a
circuit different from that to which the
receiver is connected.
•Consult the dealer or an experienced radio/TV
technician for help.
This Class A digital apparatus meets all
requirements of the Canadian Interference-
Causing Equipment Regulations.
This symbol is intended to alert
the user to the presence of
uninsulated “dangerous voltage”
within the product’s enclosure
that may be of sufficient
magnitude to constitute a risk
of electric shock to persons.
The exclamation point within an
equilateral triangle is intended
to alert the user to the presence
of important operating and
maintenance (servicing)
instructions in the literature
accompanying the product.
CAUTION TO REDUCE THE RISK OF
ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE,
REFER SERVICING TO QUALIFIED SER-
VICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
Warning
To prevent fire or shock hazard, do not expose
the unit to rain or moisture.
To avoid electrical shock, do not open
the cabinet Refer servicing to qualified
personnel only.
Wiring methods shall be in accordance
with the National Electric Code,
ANSI/NFPA 70.
This product is manufactured to comply with the radio interference
requirements of EEC DIRECTIVE 89/336/EEC, 93/68/EEC and
73/23/EEC.
Table of Contents
3
Safety precautions . . . . . . . . . . . . . . . . . . . . . . . . . . 4
What's in the box . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Construction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7
•Front view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
•Side view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
•Rear view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-11
•Video cable connection. . . . . . . . . . . . . . . . . . . . . . 8
•Camera installation . . . . . . . . . . . . . . . . . . . . . . 9-10
•Camera connection . . . . . . . . . . . . . . . . . . . . . . . 11
Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-14
•4-pin dip switch setting . . . . . . . . . . . . . . . . . . . . . 12
•Backlight compensation setting . . . . . . . . . . . . . . 13
•Line lock phase adjustment volume. . . . . . . . . . . . 14
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Dimension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
4
Safety precautions
Do not use strong
solvents or detergents
Use a dry cloth to the camera when it is
dirty. If it is hard to remove the dirt on
the camera, use a mild detergent and
wipe it gently.
Before operating, please
check proper temperature,
humidity and power
source ratings.
Use the camera under conditions where
temperature is between -10°C ~ 50°C.
Avoid the camera with
direct sunlight
Do not aim the camera at bright objects.
Never face it with direct sunlight or other
extremely bright objects. Otherwise
blooming or smear may be caused.
Do not attempt to disas-
semble the camera
To prevent electric shock, do not remove
screws or covers. There are no user
serviceable parts inside. Ask a qualified
service personnel for servicing.
Handle the camera
with care
Do not abuse the camera. Avoid striking,
shaking, etc. The camera could be dam-
aged by improper handling or storage.
Do not expose the cam-
era to rain or moisture
This product is designed for indoor use
or location where it is protected from
rain and moisture. When exposed to
moisture, turn the power off immediate-
ly and ask a qualified service personnel
for servicing. Moisture can damage the
camera and also create the danger of
electric shock.
Do not expose the camera
in such conditions as
shown below.
Use in a room or area filled with ciga-
rette smoke, dust or gas.
5
What's in the box
Camera Body
M4 Tapping Screws
(2EA)
(Pan Lock Screw)
Accessory
Video Cable
6
Construction
Front view
Side view
GVI logo
4-pin Dip Switch
Tilt Base
Zoom Lever
Tilting Lock Screw
Focus Lever
Dome Cover
Lens
Tilting Lock Screw
Dome Cover Separatory
Spring
Construction
7
Rear view
Dome Cover Separatory
Spring
GND
Video Out
AC Power In
Pan Base
Base Fixing Hole
Installation
8
Video Cable Connection
1. AC 24V
2. AC 24V
3. WHITE : Connect the WHITE Cable to 3(V).
4. BLACK : Connect the BLACK Cable to 4(G).
WHITE Cable
BLACK Cable
AC 24V
9
Installation
Camera Installation
1. Aim the GVI logo to the place that you wish to watch.
2. Tighten the M4 Tapping Screws to fix the Dome Camera on
the ceiling, then adjust the Pan(Left/ Right) by moving the
Pan Base. Tighten the M4 Tapping Screws after adjustment.
3. Loosen the Tilting Lock Screw. Adjust the Tilt (Up /Down) by
moving the Tilt Base then tighten Tilting Lock Screw.
4. Set the Zoom Lever to a point between Tele and Wide to
choose the desired angular field of view.
Set the Focus Lever to a point between Near and Far to
choose the desired focus of view.
5. Install the Dome Cover to the main body by turning it coun-
terclockwise to the end.
Dome Cover
Focus Lever
(Near/Far)
Pan Base
Hole for Fixing
Tilting Lock Screw
Zoom Lever
(Tele/Wide)
Tilt Base
Installation
10
NOTE
•When you disassemble the Dome Cover, lift the Dome Cover
Separatory Spring on the opposite side of GVI logo and turn
the Dome Cover clockwise simultaneously.
•When you install the camera, handle with care. The camera
could be damaged by improper handling or storage.
Dome Cover
Separatory Spring
This manual suits for next models
3
Table of contents
