Grundig GD-RT-BC30004N User manual
1
Quick Guide
About this guide
The guide includes instructions for using and managing the product.
Pictures, charts, images and all other information hereinafter are for
description and explanation only. The information contained in the
guide is subject to change, without notice, due to firmware updates
or other reasons.
Please find the latest version at WWW.GRUNDIG-SECURITY.COM
Limitation of Liability / Legal Disclaimer
Abetechs GmbH (Grundig Security) undertakes all reasonable efforts
to verify the integrity and correctness of the contents in this
document, but no formal guarantee shall be provided. Use of this
document and the subsequent results shall be entirely on the user’s
own responsibility. Abetechs GmbH (Grundig Security) reserves the
right to change the contents of this document without prior notice.
Design and specifications are subject to change without prior notice.
The product described herein, with its hardware, software and
documentation is provided “as is”, without any warranty, expressed
or implies, including without limitation, merchantability, satisfactory
quality, fitness for a particular purpose, and non-infringement of a
third party.
In no event will our company and its employees or agents be liable to
you for any special, consequential, incidental, or indirect damages,
including among others, damages for loss of business profits,
2
business interruption, or loss of data or documentation, in
connection with the use of this product, even if our company has
been advised of the possibility of such damages.
Regarding to products with internet access, the use of the product
shall be wholly at your own risks. Our company shall not take any
responsibilities for abnormal operation, privacy leakage or other
damages resulting from cyber-attack, hacker attack, virus inspection,
or other internet security risks; however our company will provide
timely technical support if required. Surveillance laws vary by
jurisdiction before using this product in order to ensure that your use
conforms to the applicable law. Our company shall not be liable in the
event that this product is used with illegitimate purposes.
In the event of any conflicts between this manual and the applicable
law, the later prevails.
Trademark
Each of trademarks herein is registered. The name of this product and
other trademarks mentioned in this manual are the registered
trademark of their respective company.
Copyright of this document is reserved. This document shall not be
reproduced, distributed or changed, partially or wholly, without
formal authorization.
OPEN SOURCE SOFTWARE LICENSE INFORMATION
The software components provided with Grundig products may
contain copyrighted software that is licensed under various open-
source software licenses. For detailed information about the
contained open-source software packages, the used package
3
versions, license information and complete license terms, please
refer to the product detail pages on our website. The complete open-
source software license information is also included in firmware files
of affected products. Please also check your product’s CD-ROM and
manuals for additional information.
You may obtain the complete corresponding open-source part of a
specific product from us for a period of three years after our last
shipment of this product by sending an email to: info@grundig-
security.com
Safety and Installation Instruction
Introduction
Please read these instructions carefully and keep them for future
reference. You must heed all the warnings and cautions as well as
follow all the safety and installation instructions.
The appearance of the products, functions and firmware or software
upgrade may differ from this manual.
GRUNDIG reserves the right to perform needed changes without prior
notice.
Safety Instructions
Make sure that you only use the power adapter that is specified in the
specifications sheet of the product. If you use any other adapter or
connect the power supply incorrectly, this may cause explosion, fire,
electric shocks or damage the product. Do not connect several
devices to one power adapter as this may cause an adapter overload
4
and can lead to over-heating and fire. Make sure that the plug of the
power adapter is firmly connected to the power socket.
Do not place containers with liquids on the product. Do not place
conducting items like tools, screws, coins or other metal items on the
product. These may fall from the product or can cause fire or electric
shocks or other physical injuries.
Do not push or insert any sharp items or any objects into the device
as this may cause damage to the product, fire, electric shocks and/or
physical injuries.
Do not block any ventilation openings, if there are any. Ensure that
the product is well ventilated to prevent any over-heating. Do not
subject the device to physical shock or drop the product.
If the product uses batteries, please use a battery type that is
recommended by the manufacturer. Improper use or replacement of
the battery may result in the hazard of explosion.
Do not use any accessories that are not recommended by GRUNDIG.
Do not modify the product in any way.
If the product starts to smell or smoke comes out of the device,
immediately stop using the product and disconnect it from the power
supply to prevent fire or electric shocks. Then contact your dealer or
the nearest service center.
If the product does not work correctly, contact your dealer or nearest
service center. Never open, disassemble or alter the product yourself.
GRUNDIG cannot accept any liability or responsibility for problems
caused by attempted and unauthorized repair and maintenance.
Installation Instructions
5
It is necessary to fix the device firmly if the product is installed on a
wall or ceiling. Do not install the product on surfaces or in places that
are vibrating. Do not install the product near radiation sources.
Do not install the product near heat sources, like radiators or other
equipment that produces some heat. If the product is not classified
by any IP class, do not install the product in very cold or hot
temperatures (please refer to the working temperature specified in
the specification sheet of the product), dusty, dirty or damp
environment.
If the product is classified by any IP class, never touch the product
cover directly with your fingers, because the acidic sweat of the
fingers may damage the surface coating of the product cover. To clean
the inside and outside of the product cover, use a soft and dry cloth.
In any case, do not use alkaline detergents. The correct configuration
of all passwords and other security settings is the sole responsibility
of the installer and/or end-user (this applies especially to IP Cameras
and Recorders).
Special Installation Instructions for Recorders (NVRs and DVRs)
Make sure that the last actual firmware is installed on the IP Device.
You may get the actual firmware from www.grundig-security.com
website or from tech-support@grundig-security.com.
Make sure that the product is secured after installation and locate the
recorder in safe places where children are not able to reach it.
Make sure the device is properly secured to a rack or shelf. Major
shocks or jolts to the unit as a result of dropping it may cause damage
to the sensitive electronics within the unit.
6
Make sure the device is installed in a room that is well-ventilated and
dust-free.
Power down the unit before connecting and disconnecting
accessories and peripherals.
Only use an HDD for this device that is recommended by GRUNDIG.
The USB flash drive can only be connected to the USB-port of the
device.
Use the device in conjunction with an UPS if possible.
To clean the product, gently wipe the outside with a clean dry cloth.
7
Table of content
1 Rear Panel Interfaces Description .................................................. 9
2 Installation and Connections ....................................................... 10
DVR Installation ................................................................. 10
HDD Installation ................................................................ 10
Bracket Installation ............................................ 10
Fix-on-Bottom Installation ................................. 11
RS-485 and Camera Connection ........................................ 12
3 Menu Operation .......................................................................... 13
3.1 Startup .............................................................................. 13
13
Activate Device .................................................................. 13
Set Unlock Pattern ............................................................. 15
User Login ......................................................................... 16
User Logout, Shutdown and Reboot .................................. 17
Configure Signal Input ....................................................... 17
Network Settings ............................................................... 18
Configure General Settings ................................ 18
SCMS 19
8
Add IP Cameras ................................................................. 20
Connect PoC Cameras ....................................................... 21
Live View ......................................................................... 22
Recording Settings ........................................................... 23
Playback .......................................................................... 23
4 Accessing by Web Browser .......................................................... 24
9
1 Rear Panel Interfaces Description
The rear panel interfaces vary with different models. Refer to Table
1-1 for the common interface description of rear panels.
Common Interfaces Description of Rear Panels
Item Description Item Description
VIDEO IN
BNC interface
for Turbo HD
and analog
video input
VIDEO
OUT
BNC connector
for video output
AUDIO IN RCA connector AUDIO
OUT RCA connector
LINE IN
Connector for
two-way audio
input
USB
Interface
USB port for
additional
devices
VGA
DB15 connector
for VGA output.
Displays local
video output
and menu.
HDMI
HDMI video
output
connector
RS-485
Interface
Connector for
RS-485 devices
RS-232
Interface
Connector for
RS-232 devices
LAN Connector for
network eSATA
Storage and
expansion
interface for
record or backup
ALARM
IN/OUT
Connector for
alarm
input/output
GND Ground
Power
Switch
Switch for
turning on/off
the device
Power
Supply
100 to 240 VAC,
48 VDC, or 12
VDC for different
models
This manual suits for next models
2
Table of contents
Other Grundig DVR manuals
Grundig
Grundig GD-RT-AC3004N User manual
Grundig
Grundig GPVR1250 User manual
Grundig
Grundig VIVANCE GV 3200 VPS User manual
Grundig
Grundig DVR User manual
Grundig
Grundig GV 400 Building instructions
Grundig
Grundig GV 6300 EURO User manual
Grundig
Grundig VIVANCE GV 3042 NIC User manual
Grundig
Grundig GU-RN-AC8104P User manual
Grundig
Grundig VIVANCE GV 3143 HIFI User manual
Grundig
Grundig XERIA GV 6263 HIFI User manual
Grundig
Grundig GRH-K1004A User manual
Grundig
Grundig GRA-D2208B User manual
Grundig
Grundig GV 464 HIFI VPT User manual
Grundig
Grundig GD-RT-AC3004N User manual
Grundig
Grundig VIVANCE GV 3242 NIC/2 User manual
Grundig
Grundig GU-RN-AC8104P User manual
Grundig
Grundig GV 26 Series User manual
Grundig
Grundig GRT-K1104A User manual
Grundig
Grundig Freeview GDVR1TBFV User manual
Grundig
Grundig GDVR501FV User manual
